| 67.7. Settings | ||
|---|---|---|
 | Chapter 67. HowTo - Abilisphone - End user manual |  |
| 67.7. Settings | ||
|---|---|---|
| | Chapter 67. HowTo - Abilisphone - End user manual | |
You may create the Abilis VoIP account in the abilisphone when you start the abilisphone and the account is not yet configured.
You may also create it later via settings page (Press the "Configure Abilis Account" option in Abilis Accounts area)
Press "Configure Abilis Account" and set the following parameter
Table 67.1. Abilisphone account parameters
| Parameter name | Meaning | Example |
|---|---|---|
| Username | The user name in Abilis CPX | test |
| Password | The password of the user | mypassword |
| Abilis Domain | The FQDN or IP of the Abilis CPX | 80.80.80.80 |
Below Abilis Account settings there is the area of the XMPP/Jabber server account (Messages Server).
Just insert the following parameters:
Table 67.2. Abilisphone messaging account
| Parameter name | Meaning | Example |
|---|---|---|
| Enable messaging | Enable/Disable the messaging account | yes |
| Username | The user name in XMPP server | user |
| Password | The password of the user in XMPP server | p432J43jD9 |
| Domain | The domain of the XMPP server | serverdomain |
| Require SSL/TLS | Enable/Disable the encryption | yes |
In this sub-section of the settings you may specify parameters useful to support advanced Abilis feature.
Let's check all the parameters in this area.
Table 67.3. Abilis parameters
| Parameter name | Meaning | Example |
|---|---|---|
| Data over Mobile Network | Enable/Disable the access to GPRS/EDGE/UMTS/HDSPA from the abilisphone | yes |
| Use Wi-Fi | Enable/Disable the access to Wi-Fi from the abilisphone | yes |
| Enable Vibration | Enable/Disable the vibration in incoming VoIP calls | no |
| Reject incoming VoIP calls | Enable/Disable the rejection of the incoming VoIP calls | no |
| Abilis Features | Enable/Disable the feature provided by Abilis like DISA and Callback. | yes |
| Enable Callback | Enable Data/SMS/Blind callback | yes |
| Enable Postselection | Enable the GSM Postselection via the You&Me number | yes |
| Postselection Short Delay | Apply a pause of two seconds instead of four seconds before sending the DTMF in a GSm postselection. In some case it should be disabled. | yes |
| You&Me number | The number of GSM postselection service | +393331111111 |
| Callback number | The number used to request a Blind Callback | +393337777777 |
| Server's numbers | The number of Callback SIMs, more SIM may be specified using a comma as separator | +393332222222,+393334444444 |
| SMS Destination Number | The destination number of a callback request via SMS. | +393335555555 |
| Enable Dial Out Prefix | Adds a prefix to dialed numbers | yes |
| Dialout Prefix | The prefix for dialout | 0 |
| Enable Internal Prefixes | Enable internal prefixes parsing | yes |
| Internal Prefixes | Comma separated list of prefixes that are handled as internal (without dialout prefix) | 5,8 |
| Use encryption | Enable the encryption in SIP calls | yes |
| Specific Model Settings/Samsung Galaxy compatibilty | Enable special handling of some Samsung Galaxy model, use it in case of audio troubles (i.e. volume saturation in VoIP calls) | no |
In this sub-section of the settings you may specify the preferences.
Let's check all the parameters in this area.
Table 67.4. Preferences parameters
| Parameter name | Meaning | Example |
|---|---|---|
| Advanced/Abilis port | UDP port for connection with Abilis | 45678 |
| Advanced/Link Evaluator port | Link Evaluator Port | 56789 |
| Codecs | The codecs available in VoIP calls | Spirit 8K and PCMA |
| Start at boot time | Enable abilisphone to be automatically restarted with the phone | yes |
| Replace + by 00 | In VoIP calls replaces "+" prefix with the "00" prefix | yes |
In the Codecs area the codec may be enabled/disabled via a checkbox
| |  | |
| 67.6. Contacts (Address Book) |  | 67.8. Frequenty Asked Questions |