| 69.17. How to configure DATA CALL BACK using an CELL Key, calling an ISDN number | ||
|---|---|---|
 | Chapter 69. HowTo - CTI system |  |
| 69.17. How to configure DATA CALL BACK using an CELL Key, calling an ISDN number | ||
|---|---|---|
| | Chapter 69. HowTo - CTI system | |
Enter into the Abilis control-program or open the configuration file with the Console configurator and type the following commands.
| a dev:cellkey-1 | Add the cellkey-1 device. |
| warm start | Restart Abilis. |
Type the following commands to configure the ip resource:
| a res:ip-22 subtype:ppp | Add an IP over PPP resource |
| s p ip-22 lowres:ctislink | Set to CtiSLink the lowres of the ip resource |
| s p ip-22 nat:outside | Enable nat for the ip resource. |
| s p ip-22 dial-in:no dial-out:yes | Prevent the ctislink to accept incoming calls and let to perform outgoing calls. |
| s p ip-22 nrty:30 rty:us | Configure the number of calls retry |
| s p ip-22 nrty3:nomax | Configure the PPP authentication number retry. |
| s p ip-22 cdo:99 | Configure the called output number. |
| s p ip-22 username:provider_user password:provider_pwd | Configure the login information. |
| s p ip-22 local:chap,pap remote:none | Configure the local and remote authentication protocol. |
| s p ip-22 descr:UMTS-DATA | Configure the local and remote authentication protocol. |
| save conf | Save the configuration. |
| warm start | Restart Abilis. |
Type the following commands to configure CTIDISA resource:
a res:ctidisa or s act res:ctidisa | Add the CTIDISA resource. or If the resource already exists, set it active. |
| s p ctidisa restricted-calling:yes | Rejects calls from calling numbers that are not present in CTIDISA User table. |
| s p ctidisa act:yes | Enable the CTIDISA runtime functionalities. |
| save conf | Save the configuration. |
| warm start | Restart Abilis. |
| a ctidisa service:data_cb | Add the data_cb service. |
| s ctidisa service:data_cb mode:data-cb cdi:888 cd-res:ip-22 | Configure the service to use the ip resource above for data call back when the input called number is 888. |
| save conf | Save the configuration. |
| warm start | Restart Abilis. |
Type the following commands to configure the data routing:
| a ctir pr:1 descr:umts-data type:data cdi:* poi:ctislink poo:501 | Add a rule to route data to ctip 501. |
| a ctir pr:2 descr:DISA_data_cb type:vtod cdi:999901 cgi:393331234567 cdo:888 sp:64000 coders:g.711 | Add a rule to route a call incoming from an ISDN line to
DISA, when the calling number is a mobile phone. |
| init ctir | initialize the CTIR resource. |
| save conf | Save the configuration. |
![[Note]](../images/note.png) | Note |
|---|---|
The result is that calling the isdn number 999901 from the number 3331234567, the call is rejected and an internet connection is established using the UMTS Key. The key acquires a dynamic IP address so the configuration of Dynamic DNS is needed to reach Abilis. Besides, a correct configuration of NAT resource may be necessary for example to reach a server located behind Abilis or to enable navigation toward internet from LAN. |
| |  | |
| 69.16. How to configure Last Calling Service |  | 69.18. How to configure CTISMS to send sms using the web interface |