| 78.1. System Log messages | ||
|---|---|---|
 | Chapter 78. Log messages |  |
| 78.1. System Log messages | ||
|---|---|---|
| | Chapter 78. Log messages | |
Example:
[15:41:54] ABILIS_CPX:d lCurrent Local Time: Monday 25/05/2015 13:38:17 (UTC+2.00) 25/05/2015 12:06:30 [00033] WARM START 25/05/2015 12:06:42 [00103] -------------------- NEW RUN -------------------- 25/05/2015 12:06:42 [00398] I: ABILIS CPX Ver. 8.0.3/STD - Build 3961.10 25/05/2015 12:06:42 [00079] I: MULTI-CPU MODE DISABLED FOR THIS HARDWARE 25/05/2015 12:06:42 [00079] I: USING 1 CPU 25/05/2015 12:06:42 [00474] I: CPU clock 1000 MHz 25/05/2015 12:06:44 [00362] I: WATCHDOG MFPCIGT FW Rev. 6 25/05/2015 12:06:44 [00459] I: ABILIS-ID:800733 25/05/2015 12:06:44 [00163] I: SYSTEM RESET 25/05/2015 12:06:44 [00195] I: CHKDSK C: OK 25/05/2015 12:06:45 [00371] I: LICENCE, LOADED 25/05/2015 12:06:45 [00374] W: LICENCE, NPVEXT DISABLED 25/05/2015 12:06:45 [00249] I: USB PCI16/3 EHCI EE105000 10 25/05/2015 12:06:45 [00248] I: USB PCI16/0 UHCI E400 15 25/05/2015 12:06:46 [00248] I: USB PCI16/1 UHCI E500 11 25/05/2015 12:06:46 [00248] I: USB PCI16/2 UHCI E600 12 25/05/2015 12:06:49 [00079] BSE-1 ELTI-1 ST:dn 25/05/2015 12:06:49 [00242] I: BSE-1 DSP:0 DWNL OK 25/05/2015 12:06:58 [00071] TRACE ACTIVATED 25/05/2015 12:06:59 [00291] I: DSP test start 25/05/2015 12:07:00 [00292] I: DSP test end 25/05/2015 12:07:00 [00286] I: CTIR ENABLED 25/05/2015 12:07:00 [00055] SYSTEM STARTED 25/05/2015 12:07:00 [00058] CONF:ACCEPTED 25/05/2015 12:07:00 [00428] I: MfIo-1 ST:RD 25/05/2015 12:07:00 [00436] I: MfTemp-1 ST:RD 25/05/2015 12:07:00 [00091] I: Pad-1 L1-ST:dn DCD:dn DTR:UP 25/05/2015 12:07:00 [00411] I: Nat-1 ST:RD 25/05/2015 12:07:00 [00345] I: Dhcp-1 ST:RD 25/05/2015 12:07:00 [00180] I: CtiP-31 L1-ST:dn 25/05/2015 12:07:00 [00182] I: CtiP-31 SapiX25:in 25/05/2015 12:07:00 [00180] I: CtiP-32 L1-ST:dn 25/05/2015 12:07:00 [00182] I: CtiP-32 SapiX25:in 25/05/2015 12:07:00 [00180] I: CtiP-33 L1-ST:dn 25/05/2015 12:07:00 [00182] I: CtiP-33 SapiX25:in 25/05/2015 12:07:00 [00180] I: CtiP-34 L1-ST:dn 25/05/2015 12:07:00 [00182] I: CtiP-34 SapiX25:in 25/05/2015 12:07:00 [00095] I: Eth-1 ST:NG 25/05/2015 12:07:00 [00090] I: X25-999 Layer3:down 25/05/2015 12:07:00 [00089] I: X25-999 Layer2:cg 25/05/2015 12:07:00 [00092] I: X25-999 PLink:ln SLink:RD 25/05/2015 12:07:00 [00461] I: NPv-1 ST:UP 25/05/2015 12:07:00 [00462] I: NPvl-1 P1:dn P2:- B:- B-C:- 25/05/2015 12:07:00 [00462] I: NPvl-2 P1:dn P2:- B:- B-C:- 25/05/2015 12:07:00 [00092] I: Ip-7 PLink:d2 SLink:ln 25/05/2015 12:07:00 [00346] I: DhcpC-1 ST:RD 25/05/2015 12:07:00 [00092] I: Pv-1 PLink:d1 SLink:ln 25/05/2015 12:07:00 [00092] I: Ip-6 PLink:d2 SLink:ln 25/05/2015 12:07:00 [00095] I: Eth-3 ST:NG 25/05/2015 12:07:00 [00095] I: Eth-2 ST:RD 25/05/2015 12:07:00 [00406] I: Trfa-1 ST:RD 25/05/2015 12:07:00 [00492] I: Ups-1 USB-ST:ds 25/05/2015 12:07:00 [00493] I: Ups-1 POWER:na BATT:na 25/05/2015 12:07:00 [00442] I: Vs-1 ST:RD 25/05/2015 12:07:00 [00231] I: IpSec-1 ST:RD 25/05/2015 12:07:00 [00232] I: Ike-1 ST:RD/RD 25/05/2015 12:07:00 [00259] I: PoeAc-1 ST:ee 25/05/2015 12:07:00 [00020] W: EVENTS LOST 25/05/2015 12:07:00 [00104] AUTO SAVE IN PROGRESS 25/05/2015 12:07:02 [00107] AUTO SAVE OK 25/05/2015 12:07:07 [00462] I: NPvl-1 P1:UP P2:- B:- B-C:- 25/05/2015 12:07:07 [00462] I: NPvl-2 P1:UP P2:- B:- B-C:- 25/05/2015 12:07:23 [00092] I: Ip-7 PLink:RD SLink:ln 25/05/2015 12:07:23 [00092] I: Ip-6 PLink:RD SLink:ln 25/05/2015 12:07:23 [00092] I: Ip-8 PLink:RD SLink:ln
![[Tip]](../images/tip.png) | Tip |
|---|---|
The command allows to display a log file of another version: [09:22:13] ABILIS_CPX:_ |
Notification messages are stored in the Abilis CPX System Log file in the following format:
Table 78.1. System Log event's format
| Date | Time | Event Code | Event Text |
|---|---|---|---|
| dd/mm/yyyy | hh:mm:ss | [nnnnn] | Textual message |
Notification messages are classified on the basis of importance of the reported event. The event importance is indicated by a prefix reported in the text of the event message itself.
The following table lists Event types and the corresponding Event text prefix:
Table 78.2. System Log event's classification
| Event type | Event text prefix | Meaning |
|---|---|---|
| Unclassified | none | Indications of general events. |
| Error | E: | Notifications of critical errors which require the reset of Abilis CPX. All the sessions are closed and Abilis CPX automatically restarts. Note that an exception is generated and saved in the Exceptions Log for a possible use by Abilis engineers. |
| Warning | W: | Notifications of not critical events that could be caused by some malfunction. The reason must be carefully identified, but the system will continue to function. |
| Informative | I: | Notifications of events of particular interest that occur in the regular system operation. |
Each message also has a Severity level indicator, based on SYSLOG protocol severity classification. See SYSLOG section for a description of SYSLOG Message Severities.
Table 78.3. System Log event's List
| Event code | Severity | Event Text | Meaning |
|---|---|---|---|
| 00020 | WARNING | W: EVENTS LOST | Events has been lost because system wasn't able to write all of them into the log file. Usually this events could appears at system start-up when many events are generated at the same time. |
| 00021 | INFO | <message string> | This event is used to signal high priority messages, that could be meaningless for the user, but that are very useful for the Abilis CPX technicians for solving eventual problems. |
| 00022 | INFO | CONF:MISSING CFG | The configuration file drivers.cfg is
missing. |
| 00023 | INFO | CONF:LOAD BCK | Abilis CPX is loading the configuration backup file
drivers.bck, because configuration file
drivers.cfg is missing or not valid. |
| 00024 | INFO | CONF:MISSING BCK | The configuration backup file
drivers.bck is missing. |
| 00025 | INFO | CONF:CORRUPTED | Error in the content or in the format of configuration file
drivers.cfg. |
| 00026 | INFO | CONF:INVALID BCK | Error in the content or in the format of configuration
backup file drivers.bck. |
| 00027 | ERROR | E: DEBUG LOG Err:xx | Error in Debug Log Service. 'xx' is the error code to be reported to the Abilis CPX Help desk. |
| 00028 | ERROR | E: E00 | The System exit because Esc or Alt/X key was pressed by the user. |
| 00029 | ERROR | E: PO1 | Software exception of type 01. Note that software exceptions are generated and saved in the Exceptions Log for a possible use by Abilis engineers. |
| 00030 | ERROR | E: PO2 | Software exception of type 02. Note that software exceptions are generated and saved in the Exceptions Log for a possible use by Abilis engineers. |
| 00031 | ERROR | E: PO3 | Software exception of type 03. Note that software exceptions are generated and saved in the Exceptions Log for a possible use by Abilis engineers. |
| 00032 | INFO | AUTO WARM START | Automatic restart of Abilis CPX usually caused by an error. |
| 00033 | INFO | WARM START | A request for unconditional system restart has been submitted by the user, through the WARM START command. |
| 00034 | INFO | RESTART SYSTEM | A request for system restart has been submitted by the user through the RESTART SYSTEM command. The RESTART SYSTEM can be either issued to the command interpreter of the CP (Control Port) resource or executed from the the Abilis CPX frontal panel. |
| 00035 | ERROR | E: C01 | Error in the DCP Service (i.e. the data compression/expansion service) during allocation of data compression/expansion buffers. |
| 00036 | ERROR | E: Mdd | Error in memory allocation phase. 'dd' is the error code to be reported to the Abilis CPX Help desk. |
| 00037 | ERROR | E: Mxx yy | Error in memory allocation phase. 'xx' and 'yy' are the error code and sub-code to be reported to the Abilis CPX Help Desk. |
| 00038 | ERROR | E: Nxx yy ddd zz | Error in the Ncb exchange between two drivers. 'xx' represents the hexadecimal value of the driver's return code; 'yy' represents the hexadecimal code of the command which has caused the warning; 'ddd' represents the driver's port number; 'zz' represents and additional code whose usage is intended for Abilis engineers only. |
| 00039 | ERROR | E: D00 xxxx | Software driver error of type 00. 'xxxx' is the error sub-code that must be reported to the Abilis CPX Help Desk. |
| 00040 | ERROR | E: D01 xx yy | Software driver error of type 01. 'xx' and 'yy' are the error code and sub-code to be reported to the Abilis CPX Help Desk. |
| 00041 | ERROR | E: D02 xx | Software driver error of type 02. 'xx' is the error sub-code that must be reported to the Abilis CPX Help Desk. |
| 00042 | ERROR | E: D03 | Software driver error of type 03; it must be reported to the Abilis CPX Help Desk. |
| 00043 | ERROR | E: B01 xxxx | The Configuration Service detected that a mandatory configuration block is missing. 'xxxx' is the exadecimal code that identifies the configuration block. |
| 00044 | ERROR | E: B02 xxxx | The Configuration Service detected that a configuration block is corrupted. 'xxxx' is the exadecimal code that identifies the configuration block. |
| 00045 | ERROR | E: Xxx | Software error in “exit” function installation. “xx” is the exadecimal code that identifies the software function for which the error is generated and that must be reported to the Abilis CPX Help Desk. |
| 00046 | ERROR | E: GSxx | Error in Global Submit Service. 'xx' is the exadecimal code that identifies the error and that must be reported to the Abilis CPX Help Desk. |
| 00047 | ERROR | E: Gxx yyyy | Generic software errors. 'xx' and 'yy' are the error code and sub-code to be reported to the Abilis CPX Help Desk. |
| 00048 | ERROR | E: Axx yy ddd | Severe error in the Ncb exchange between two drivers. 'xx' represents the hexadecimal value of the driver's return code; 'yy' represents the hexadecimal code of the command which has caused the warning; 'ddd' represents the driver's port number. |
| 00049 | INFO | TIMEOUT EXIT | System exit loop timed out. |
| 00050 | ERROR | E: Txx | Error in Terminator Service. 'xx' is the exadecimal code that identifies the error and that must be reported to the Abilis CPX Help Desk. |
| 00051 | INFO | PNP REBOOT | Automatic restart of Abilis CPX caused by the PNP/PCI manager. |
| 00052 | INFO | ALARMED RESOURCEs | Indicates that there are alarmed resources. |
| 00053 | ERROR | E: OS EXIT | Severe error at operating system level. It is often caused by defective or extremely low amount of system RAM. If the problem persist after replacing or increasing the amount the system RAM, contact Abilis CPX technical assistance. |
| 00054 | INFO | <message string> | This event is used to signal low priority messages, that could be meaningless for the user, but that are useful for the Abilis CPX technicians for detecting problems. |
| 00055 | INFO | SYSTEM STARTED | The initialisation phases of the system is complete and then system is active. |
| 00056 | WARNING | I: WATCHDOG LIVE1 | The system watchdog (WDG) detected that in the previous run CPX was restarted because of Live signal 1. |
| 00057 | WARNING | I: WATCHDOG LIVE2 | The system watchdog (WDG) detected that in the previous run CPX was restarted because of Live signal 2. |
| 00058 | INFO | CONF:ACCEPTED | The previously saved main configuration has been checked
and accepted as valid because the system was able to successfully
start with it. Main configuration is stored in
drivers.cfg file, backup configuration in
drivers.bck file. |
| 00059 | INFO | CONF:REFUSED | The state of configuration file drivers.cfg is not valid (i.e. equal to 2 or 4). |
| 00060 | INFO | CONF:RESTORE | The system is going to restore configuration backup file
drivers.bck to configuration file
drivers.cfg. |
| 00061 | INFO | CONF:RESTORE ERR | Error while the system was restoring configuration backup
file drivers.bck to configuration file
drivers.cfg. |
| 00062 | INFO | CONF:BACKUP | Tis event indicates that a backup copy of the main configuration has been created. Usually it occurs after the System Log event 00058. |
| 00063 | INFO | CONF:BACKUP ERR | Error while the system was creating a backup copy of the
configuration file drivers.cfg into the
backup configuration file
'drivers.bck. |
| 00064 | WARNING | W: C03 dd | This event is generated by the DCP Service (i.e. the data compression/expansion service) to inform that only a sub-set of the dictionaries is available. Usaully this is caused by an insufficient system memory. 'dd' is the number of dictionaries that are currently available in the system. |
| 00065 | WARNING | W: C02 | This event is generated by the DCP Service (i.e. the data compression/expansion service) to inform that no dictionaries are available. By consequence the data compression is not available. Usually this is caused by an insufficient system memory. |
| 00066 | WARNING | W: C04 D:xx R:yy | This event is used to signal that DCP Service (i.e. the data compression/expansion service) initialization fails. 'xx' is the exadecimal code that identifies a dictionary; 'yy' is the exadecimal code that identifies the error that must be reported to the Abilis CPX Help Desk. |
| 00067 | INFO | SAVING DEBUG LOG | Debug Log is going to be saved into the
cpx.dbg file. |
| 00068 | INFO | DEBUG LOG SAVED | Debug Log was successfully saved into the file
cpx.dbg. |
| 00069 | INFO | DEBUG LOG ERROR | Debug Log was not saved into the file
cpx.dbg, because it was empty. |
| 00070 | INFO | DEBUG LOG ERROR | Debug Log was not saved into cpx.dbg
file, because an error occurred. |
| 00071 | INFO | TRACE ACTIVATED | Ncb Trace activated at system start up. This event signals that the function for tracing internal events has been automatically activated at the system start-up. |
| 00072 | INFO | TRACE NOT ACTIVE | Ncb Trace not activated because an error occurred. This event signals that it was not possible to activate the tracing of internal events at the system start-up. |
| 00073 | WARNING | W: Axx yy ddd | Ncb management error. Error in the Ncb exchange between two drivers. It must be reported to the Abilis CPX Help desk. 'xx' represents the hexadecimal value of the driver's return code; 'yy' represents the hexadecimal code of the command which has caused the warning; 'ddd' represents the driver's port number. |
| 00074 | WARNING | W: L94 | Error in the length of data part of the Ncb exchanged between two drivers, that must be reported to the Abilis CPX Help desk. This event is usually followed by the System Log event 00075. |
| 00075 | WARNING | xxxx LSN:yy P:ddd | Error in the length of data part of the Ncb exchanged between two drivers, that must be reported to the Abilis CPX Help desk. This event is always preceded by the System Log event 00074. 'xxxx' is the hexadecimal value of the length of data part; 'yy' represents the hexadecimal code of the command which has caused the warning; 'ddd' represents the driver's port number. |
| 00076 | INFO | MAIN_STACK SIZE < 2500 BYTES | The Main thread stack is less than 2500 bytes. |
| 00077 | INFO | I: Sim-nnn Lsn:xx CONNECTED | This event is generated by the SIM (Simulator) resource to signal a connection establishment. 'nnn' is the resource identifier; 'xx' is the connection identifier. |
| 00078 | INFO | I: Sim-nnn Lsn:xx DISCONNECTED | This event is generated by the SIM (Simulator) resource to signal a connection closing. 'nnn' is the resource identifier; 'xx' is the connection identifier. |
| 00079 | INFO | <message string> | This event is used by software drivers to write generic messages into the System Log file. Usually this messages are meaningless for the user, but they could be useful for Abilis engineers for sw debugging. |
| 00080 | INFO | DPMI MEMORY STATISTICs N/A | DPMI memory status check function fail. |
| 00081 | WARNING | W: C05 | DCP Service (i.e. the data compression/expansion service) has been reinitialised. |
| 00082 | WARNING | W: RC:xx NCB:yy Type-nnn (ddd) | Unexpected return code in the Ncb exchange between two drivers. It must be reported to the Abilis CPX Help desk. 'xx' represents the hexadecimal value of the driver's return code; 'yy' represents the hexadecimal code of the command which has caused the warning; 'Type-nnn' are the driver's resource type and identifier; 'ddd' is the driver's port number. |
| 00083 | WARNING | W: WATCHDOG START | The system watchdog (WDG) detected that in the previous run the CPX boot phase was timed-out. |
| 00084 | ERROR | E: HWINT ERROR | Hardware interfaces (system watchdog (WDG), Front panel, LCD, ...) initialization fail. |
| 00085 | WARNING | W: ALARM SETTED | An alarm is on. |
| 00086 | W: ALARM RESET | The ALARM RESET command has been issued. | |
| 00087 | INFO | I: Sim-nnn CAUSE: F1,xx | This event is generated by the SIM (Simulator) resource to inform about a connection closing cause. 'nnn' is the resource identifier; 'F1,xx' are the connection close cause and diagnostic codes. |
| 00088 | INFO | I: Sync-nnn ST:s1 DCD:s2 DTR:s3 | Diagnostic information about a Synchronous resource; 'nnn' is the resource identifier; 's1' is the Layer 1 state [down, UP, HT (Halted), FL (failed)]; 's2' is the DCD signal state [dn (down), UP, NA (Not Available)]. |
| 00089 | INFO | I: X25-nnn Layer2:ssss | Diagnostic information about the Layer 2 (LAPB) of an X.25 resource; 'nnn' is the resource identifier; 'ssss' is the Layer 2 (LAPB) state[down, cg (connecting), CONN (connected), frmr (FRMR), wait (waiting)]. |
| 00090 | INFO | I: X25-nnn Layer3:ssss | Diagnostic information about the Layer 3 (X.25) of an X.25 resource. 'nnn' is the resource identifier; 'ssss' is the Layer 3 (X.25) state [down, rstg (restarting), rstd (restarted), RDY (ready)]. |
| 00091 | INFO | I: Pad-nnn L1-ST:s1 DCD:s2 DTR:s3 | Diagnostic information about a PAD resource. 'nnn' is the resource identifier; 's1' is the Asynchronous Layer 1 state [down, UP, HT (halted), FL (failed)]; 's2' is the DCD signal state [dn, UP, NA (not-available)]; 's3' is the DTR signal state [dn, UP, NA (not-available)]. |
| 00092 | INFO | I: Type-nnn PLink:s1 SLink:s2 | Diagnostic information about the Link layer (MLM) of a resource. 'Type' is the resource type; 'nnn' is the resource identifier; 's1' is the P-Link state [RD (ready), ln (link not-present), le (link error), d1 (down1) d2 (down2); 's2' is the S-Link state [RD (ready), CN (connected), ln (link not-present), s1 (stopped1), s2 (stopped2)]. |
| 00093 | INFO | I: Fr-nnn ST:ssss | Diagnostic information about a Frame Relay resource. 'nnn' is the resource identifier; 'ssss' is the resource state [down, L-dn (LMI down) L-UP (LMI), BLND (blind)]. |
| 00094 | INFO | I: Ip-nnn LAN-ST:ss | Diagnostic information about the LAN layer of an Ip resource. 'nnn' is the resource identifier; 'ss' is the LAN layer state [LD (link down), LR (link ready), LN (link not-present), HD (halted), FD (failed)]. |
| 00095 | INFO | I: Eth-nnn ST:ss | Diagnostic information about a Fast Ethernet (Ethernet) resource. 'nnn' is the resource identifier; 'ss' is the resource state [DN ( down), RD (ready), TD (tx disabled), HD (halted), FD (failed), NG (negotiating)]. |
| 00096 | INFO | I: Tr-nnn ST:ss | Diagnostic information about a Token Ring resource. 'nnn' is the resource identifier. 'ss' is the resource state [HR (hw reset), SR (sw reset), TR (tx reset), IG (initializing), ID (initialized), OG (opening), ON (open), CG (closing), CD (closed), DN (down), RD (ready), HD (halted), FD (failed)]. |
| 00097 | INFO | I: Hdlct-nnn ST:ss | Diagnostic information about an HDLCT resource. 'nnn' is the resource identifier; 'ss' is the resource state [DN (down), RD (ready), ST (stopped), CL (calling), CN (connected), CR (clearing)]. |
| 00098 | INFO | I: Fr-nnn DLCI:ddddddd ST:ss | Diagnostic information about a DLCI of a Frame Relay resource. 'nnn' is the resource identifier; 'ddddddd' is the DLCI number; 'ss' is the DLCI state [nu (not-used), dn (down). id (idle), np (not-present), AC (active), in (inactive), BL (blind), rm (removed). |
| 00099 | INFO | I: Sdlc-nnn PU AD:xx ST:ss | Diagnostic information about a Physical Unit of an Sdlc resource. 'nnn' is the resource identifier; 'xx' is the Physical Unit address; 'ss' is the Physical Unit state [ dn (down), st (stopped), CN (connected)]. |
| 00100 | INFO | I: Type-nnn PLink:s1 SLink:s2 | Diagnostic information about the Multi-Links layer (ML) of a resource. 'Type' is the resource type; 'nnn' is the resource identifier; 's1' is the Global P-Links state[dn (all links are in down state), rd (some links are in ready state), RD (all links are in ready state), np (no links are present)]; 's2' is the Global S-Links state [ s1 (stopped1), RD (ready), np (no links are present)]. |
| 00101 | INFO | I: Type-nn PL-dd:ss | Diagnostic information about a P-Link of the Multi-Links layer (ML) of a resource. 'Type' is the resource type; 'nnn' is the resource identifier; 'dd' is the P-Link identifier; 'ss' is the P-Link state [dn (down), st (stopped), CN (connected)]. |
| 00102 | INFO | I: Ip-nnn PPP-ST:ss | Diagnostic information about PPP layer of an Ip resource. 'nnn' is the resource identifier; 'ss' is the PPP layer state [s1 (stopped 1 ), s2 (stopped 2), s3 ( stopped 3), DL (delaying), DN (down), UP (up)]. |
| 00103 | INFO | -------------------- NEW RUN -------------------- | This event indicates the start-up of the system: the software has been loaded and the initialisation phase is in progress. |
| 00104 | INFO | AUTO SAVE IN PROGRESS | The system has initiated the automatic saving of the
current configuration as the main configuration. Main
configuration is stored in drivers.cfg file,
backup configuration in drivers.bck
file. |
| 00105 | INFO | AUTO SAVE ABORTED | The automatic saving of the current configuration has been
aborted because of an error. Main configuration is stored in
drivers.cfg file, backup configuration in
drivers.bck file. |
| 00106 | INFO | AUTO SAVE FAIL | The automatic saving of the current configuration failed
because of an error. Main configuration is stored in
drivers.cfg file, backup configuration in
drivers.bck file. |
| 00107 | INFO | AUTO SAVE OK | The automatic saving of the current configuration was
successful. Main configuration is stored in
drivers.cfg file, backup configuration in
drivers.bck file. |
| 00108 | WARNING | W: Heap Corrupted xx | A corruption of System memory (called 'heap') has been detected. The error can be caused by a software bug or by defective system RAM memory. 'xx' is an hexadecimal code to be reported to the Abilis CPX Help desk. |
| 00109 | WARNING | W: Heap Empty xx | System memory (called 'heap') cannot be inspected. The error can be caused by a software bug or by defective system RAM memory. 'xx' is an hexadecimal code to be reported to the Abilis CPX Help desk. |
| 00110 | WARNING | W: Heap Check Fail xx | The cyclic check of System memory (called 'heap') could not be completed because it is probably corrupted. The error can be caused by a software bug or by defective system RAM memory. 'xx' is an hexadecimal code to be reported to the Abilis CPX Help desk. |
| 00111 | WARNING | W: Heap Register Err01 | The markers of a software module cannot be written in the System memory (called 'heap'). The error can be caused by a software bug or by defective system RAM memory. |
| 00112 | WARNING | W: PCI MANY CARDs | The maximum limit of 32 PCI cards which the system can support, has been reached. Report the error to the Abilis CPX Help Desk. |
| 00113 | WARNING | W: PCI LAST DEVICE PARKING CHIP SET | The chip set present on the mother board is incompatible with CPX software. Report the error to the Abilis CPX Help desk. |
| 00114 | WARNING | W: PCI UNKNOWN CHIP SET | The chip set present on the mother board is not in the list of the known ones. Report the error to the Abilis CPX Help desk. |
| 00115 | WARNING | W: PCISRV FAIL | The initialisation of the PCI service failed. Report the error to the Abilis CPX Help desk. |
| 00116 | WARNING | W: PNP FAIL | The initialisation of the PNP service failed. Report the error to the Abilis CPX Help desk. |
| 00117 | WARNING | W: PNP REFRESH FAIL | The updating of the PNP service failed. Report the error to the Abilis CPX Help desk. |
| 00118 | INFO | I: CP DTR ss RES:Sync-nnn | Execution on a Synchronous resource of the command for setting up the status of the DTR signal. 'ss' is the state of the DTR signal which has been set up [UP (up), DN (down), PL (pulse)]. 'nnn' is the Synchronous resource identifier. |
| 00119 | INFO | I: Sdlc-nnn QTEST | Reception by an SDLC resource, of a 'QLLC TEST' notification for activating the control procedure of the DTR signal. 'nnn' is the resource identifier. |
| 00120 | INFO | I: Sync-nnn DTR ss | Reception by a Synchronous resource of the command for setting up the status of the DTR signal. 'nnn' is the Synchronous resource identifier; 'ss' is the state of the DTR signal which has been set up [UP (up), DN (down), PL (pulse)]. |
| 00121 | INFO | I: CHANGE from DST to STD time mode | The system time mode is going to be changed from Daylight Savings time mode to Standard time mode. |
| 00122 | INFO | I: CHANGE from DST to STD time mode DONE | The system time mode has been changed from Daylight Savings time mode to Standard time mode. |
| 00123 | INFO | I: CHANGE from STD to DST time mode | The system time mode is going to be changed from Standard time mode to Daylight Savings time mode. |
| 00124 | INFO | I: CHANGE from STD to DST time mode DONE | The system time mode has been changed from Standard time mode to Daylight Savings time mode. |
| 00125 | INFO | I: TIME UPDATE, Delta > 1 min.(ddddddd sec.) | This event is generated by the system time synchronization service (SNTP): local date and time adjustment is in progress and the time delta, between the local clock and the synchronization Server, is greater then 1 minute. This event is followed by the System Log event 00126. 'ddddddd' is the time delta, between the local clock and the synchronization Server, in second. |
| 00126 | INFO | I: TIME UPDATE DONE | This event is generated by the system time synchronization service (SNTP): local date and time adjustment has been executed. This event appears after the System Log event 00125. |
| 00127 | WARNING | W: PVC:nn INVALID POINTER | This event is generated by the Connection Oriented Router
when it detects invalid setting in PVC structure. Please report
the error to Abilis CPX Help desk. 'nn' is the PVC identifier to
be reported to the Abilis CPX Help desk, together with the
drivers.cfg file. |
| 00128 | ERROR | E: HNDL dd | This event is generated by the software when it detects
invalid setting in internal data structure. Please report the
error to Abilis CPX Help desk. 'dd' is the data identifier to be
reported to the Abilis CPX Help desk, together with the
drivers.cfg file. |
| 00129 | WARNING | W: ACNT dd | Accounting (ACNT) driver's specific warning message. It is
the first one of a set of six messages (see System Log events
00130..00134). They are meaningless for the user, but it is useful
for Abilis engineers for sw debugging. Please report the event to
Abilis CPX Help desk. 'dd' is an internal error code to be
reported to the Abilis CPX Help desk, together with the
drivers.cfg file. |
| 00130 | WARNING | STA: dd | Accounting (ACNT) driver's specific warning message. It is
the second one of a set of six messages (see System Log events
00129..00134). They are meaningless for the user, but it is useful
for Abilis engineers for sw debugging. Please report the event to
Abilis CPX Help desk. 'dd' is an internal error code to be
reported to the Abilis CPX Help desk, together with the
drivers.cfg file. |
| 00131 | WARNING | LSN: dd | Accounting (ACNT) driver's specific warning message. It is
the third one of a set of six messages (see System Log events
00129..00134). They are meaningless for the user, but it is useful
for Abilis engineers for sw debugging. Please report the event to
Abilis CPX Help desk. 'dd' is an internal error code to be
reported to the Abilis CPX Help desk, together with the
drivers.cfg file. |
| 00132 | WARNING | MOD: dd | Accounting (ACNT) driver's specific warning message. It is
the forth one of a set of six messages (see System Log events
00129..00134). They are meaningless for the user, but it is useful
for Abilis engineers for sw debugging. Please report the event to
Abilis CPX Help desk. 'dd' is an internal error code to be
reported to the Abilis CPX Help desk, together with the
drivers.cfg file. |
| 00133 | WARNING | DRC: dd | Accounting (ACNT) driver's specific warning message. It is
the fifth one of a set of six messages (see System Log events
00129..00134). They are meaningless for the user, but it is useful
for Abilis engineers for sw debugging. Please report the event to
Abilis CPX Help desk. 'dd' is an internal error code to be
reported to the Abilis CPX Help desk, together with the
drivers.cfg file. |
| 00134 | WARNING | COD: dd | Accounting (ACNT) driver's specific warning message. It is
the sixth one of a set of six messages (see System Log events
00129..00133). They are meaningless for the user, but it is useful
for Abilis engineers for sw debugging. Please report the event to
Abilis CPX Help desk. 'dd' is an internal error code to be
reported to the Abilis CPX Help desk, together with the
drivers.cfg file. |
| 00135 | ERROR | MEMORY SUMMARY: | Informative message about the state of the system memory. It is the first one of a set of six messages (see System Log events 00136..00140). These messages indicates a possible internal error, please report the event to Abilis CPX Help desk. |
| 00136 | ERROR | TOT: nnn.nnn.nnn | Informative message about the state of the system memory. It is the second one of a set of six messages (see System Log events 00135..00140). These messages indicates a possible internal error, please report the event to Abilis CPX Help desk. 'nnn.nnn.nnn' is the total system memory size in bytes. |
| 00137 | ERROR | FREE:nnn.nnn.nnn | Informative message about the state of the system memory. It is the third one of a set of six messages (see System Log events 00135..00140). These messages indicates a possible internal error, please report the event to Abilis CPX Help desk. 'nnn.nnn.nnn' is the availble system memory size in bytes. |
| 00138 | ERROR | HU: nnn.nnn.nnn | Informative message about the state of the system memory. It is the fourth one of a set of six messages (see System Log events 00135..00140). These messages indicates a possible internal error, please report the event to Abilis CPX Help desk. 'nnn.nnn.nnn' is the used system memory size in bytes. |
| 00139 | ERROR | HLFB:nnn.nnn.nnn | informative message about the state of the system memory. It is the fifth one of a set of six messages (see System Log events 00135..00140). These messages indicates a possible internal error, please report the event to Abilis CPX Help desk. 'nnn.nnn.nnn' is the size, in bytes, of the biggest block of contiguos system memory that is currently available. |
| 00140 | ERROR | HLUB:nnn.nnn.nnn | Informative message about the state of the system memory. It is the last one of a set of six messages (see System Log events 00135..00139). These messages indicates a possible internal error, please report the event to Abilis CPX Help desk. 'nnn.nnn.nnn' is the size, in bytes, of the biggest block of contiguos system memory that is currently in use. |
| 00141 | WARNING | W: Iprtr Table OVERFLOW | The IP Router (Iprtr) routing table reached its maximum capacity. |
| 00142 | WARNING | W: Iprtr Table DANGER ON | The IP Router (Iprtr) Routings table going in DANGER state. |
| 00143 | WARNING | W: Iprtr Table DANGER OFF | The IP Router (Iprtr) Routings table exiting from DANGER state. |
| 00144 | WARNING | W: Rip Table OVERFLOW | The internal routings table of Rip driver reached its maximum capacity. |
| 00145 | WARNING | W: Rip Table DANGER ON | The internal routings table of Rip driver entered the DANGER state. |
| 00146 | WARNING | W: Rip Table DANGER OFF | The internal routings table of Rip driver exited from the DANGER state. |
| 00147 | INFO | ASSERT: Line nn, Parameter dd | This event is used by software drivers to signal unexpected conditions. They could be meaningless for the user, but that are useful for the Abilis CPX technicians for detecting problems. Please report it to the Abilis CPX Help desk. 'nn' is the line number of the file where this event is generated; 'dd' is an addition decimal code to be reported to Abilis CPX technicians. |
| 00148 | WARNING | W: FRMWR M:sss L:nnn P:ddd | This event is used by sw drivers to inform about rare conditions. They could be meaningless for the user, but they are useful for the Abilis CPX technicians for detecting problems. Please report it to the Abilis CPX Help desk. 'sss' is an addition string used to identify the origin of the event; 'nnn' is the line number of the file where this event is generated; 'ddd' is an addition decimal code to be reported to Abilis CPX technicians. |
| 00149 | INFO | I: Ip-nnn PPP-ST:s1 LINK-ST:s2 | This event reports diagnostic information about PPP layer of an Ip resource. 'nnn' is the resource identifier. 's1' is the PPP layer state [s1 (stopped 1), s2 (stopped 2), s3 (stopped 3), DL (delaying), DN (down), UP (up)]; 's2' is the PPP link state [dn (down), CN (connected)]. |
| 00150 | WARNING | W: MISSING '<file-name>' | The '<file-name>' file is missing. Please report the event to the Abilis CPX Help desk. |
| 00151 | WARNING | W: '<file-name>' Err:xx | An error (whose hexadecimal code is 'xx') occurred during the '<file-name>' file treatment. Please report the event to the Abilis CPX Help desk. |
| 00152 | WARNING | W: WATCHDOG NOT FOUND | An error occurred during Hw interface(s) (system watchdog (WDG), Front panel, LCD display, ...) initialization phase. |
| 00153 | ERROR | <message string> | This event is used to report MFIDE2 interface's warning/error messages [ “W: MF OK” (MFIDE2 interface properly initialized), “E: MF CONF MISS” (MFIDE2 interface configuration is missing), “E: WD NOTPRESENT” (Watchdog not found or not present on MFIDE2 equipment), “E: MF IDENT FAIL” (MFIDE2 interface identification failure), “E: MF DBL INIT” (MFIDE2 interface initialized more then once), “E: MF NOT INIT” MFIDE2 (interface not properly initialized). |
| 00154 | WARNING | W: PNP DISABLED | PNP service is currently disabled. |
| 00155 | WARNING | W: NAT OVERFLOW | The NAT dynamic translation table has reached its capacity limit. In this situation additional required translation cannot be performed. |
| 00156 | WARNING | W: TRACE DISK-FULL | The system wasn't able to save the Abilis CPX trace file because there wan't enough space on HD/CF. When this event occurs the Abilis CPX trace file can be either partially saved or not saved at all. |
| 00157 | WARNING | W: SWITI SSSS-NN recovery NN OK | The 'NN' attempt of the SWITI driver of card 'SSSS-NN' failure recovering procedure was successful. |
| 00158 | WARNING | W: SWITI SSSS-NN recovery NN FAIL | Failure of the 'NN' attempt of the SWITI driver of card 'SSSS-NN' failure recovering procedure. |
| 00159 | WARNING | W: SWITI SSSS-NN failure, recovering... | The SWITI driver of card 'SSSS-NN' started the failure recovering procedure. |
| 00160 | WARNING | W: SWITI SSSS-NN recovered | A failure, that has been occurred on SWITI driver of card 'SSSS-NN', has been recovered. |
| 00161 | ERROR | E: SWITI SSSS-NN unrecoverable failure | A not recoverable failure occurred on SWITI driver of card 'SSSS-NN'. For this reason the Abilis CPX system rebooted. Please report the event to the Abilis CPX Help desk. |
| 00162 | ERROR | E: SWITI error: reboot | A not recoverable error occurred on SWITI driver. For this reason the Abilis CPX system rebooted. Please report the event to the Abilis CPX Help desk. |
| 00163 | INFO | I: SYSTEM RESET | In the previous run the system was restarted using the RESTART SYSTEM command. |
| 00164 | INFO | I: RESET PRESSED | In the previous Abilis CPX run the system was restarted beacuse the RESET button was pressed. |
| 00165 | WARNING | W: WDGMEM GETERR | The system didn't save system Watchdog memory content into Abilis CPX Exception Log file, because it wasn't able to access it. Please report the event to the Abilis CPX Help desk. |
| 00166 | WARNING | W: WDGMEM EMPTY | The system didn't save system Watchdog memory content into Abilis CPX Exception Log file, because it found it was empty. |
| 00167 | WARNING | W: WDGMEM SAVERR | The system tried to save system Watchdog memory content into Abilis CPX Exception Log file, because it found it was not succesful. |
| 00168 | INFO | I: WDGMEM SAVED | The system Watchdog memory content has been successfully saved into Abilis CPX Exception Log file. |
| 00169 | WARNING | W: \USR DIR CREATE ERR-xx | The system wasn't able to create C:\USR directory at the Abilis CPX start-up. 'xx' is the error code to be reported to the Abilis CPX Help desk. |
| 00170 | WARNING | W: \USR\PUB DIR CREATE ERR-xx | The system wasn't able to create C:\USR\PUB directory at the Abilis CPX start-up. 'xx' is the error code to be reported to the Abilis CPX Help desk. |
| 00171 | WARNING | W: CONFLICTING CARD:Type-nnn DEACTIVATED | A card has been deactivated at system start up, because it
was configured to use IRQ 14 or IRQ 15 in a system where this
interrupts value should be reserved for IDE or MFIDE2 equipments.
Please report the event to the Abilis CPX Help desk, together with
the configuration file drivers.cfg. 'Type' is
the card type; 'nnn' is the card identifier. |
| 00172 | INFO | I: Ftp-nnn ST:ss | Diagnostic information about the state of FTP Server resource. 'nnn' is the resource identifier; 'ss' is the FTP Server state [in (inactive), dn (down), RD (ready)]. |
| 00173 | INFO | I: Bridge-nnn ST:s1.s2 | Diagnostic information about the state of IEEE Bridge resource. 'nnn' is the resource identifier; 's1' is the Bridge resource global state [dn (down), RD (ready)]; 's2' is the Bridge resource links global state [dn (all links are in down state), rd (some links are in ready state), RD (all links are in ready state), np (no links are present)]. |
| 00174 | INFO | I: Bridge-nnn LAN-ddd:ss | Diagnostic information about the state of a lan of IEEE Bridge resource. 'nnn' is the resource identifier; 'ddd' is the lan identifier; 'ss' is the lan state [dn (down), np (link not-present), DN (lower layer is down), RD (ready)]. |
| 00175 | INFO | I: Bridge-nnn LNK-ddd:ss | Diagnostic information about the state of a link of IEEE Bridge resource. 'nnn' is the resource identifier; 'ddd' is the link identifier; 'ss' is the link state [dn (down), np (link not-present), DN (lower layer is down), RD (ready)]. |
| 00176 | INFO | I: Arc-nnn ST:ss | Diagnostic information about the Archive resource state. 'nnn' is the resource identifier; 'ss' is the resource state [in (initialization), dn (down), RD (active/ready)]. |
| 00177 | INFO | I: Arc-nnn SES-dd:ss | Diagnostic information about a session of the Archive resource 'nnn' is the resource identifier; 'dd' is the session identifier; 'ss' is the session state [in (initialization), dn (down), RD (active/ready)]. |
| 00178 | WARNING | W: \LOG DIR CREATE ERR-xx | The system wasn't able to create C:\LOG directory at the Abilis CPX start-up. 'xx' is the error code to be reported to the Abilis CPX Help desk. |
| 00179 | INFO | I: CtiP-nnn L1-ST:ss | Diagnostic information about the Primary Rate layer 1 of a CTI port. 'nnn' is the CTI port identifier; 'ss' is the state of the layer 1 [dn (down), up]. |
| 00180 | INFO | I: CtiP-nnn L1-ST:ss | Diagnostic information about the Basic Rate layer 1 of a CTI port. 'nnn' is the CTI port identifier; 'ss' is the state of the layer 1 [dn (down), RD (ready), HL (halted), FL (failed)]. |
| 00181 | INFO | I: CtiP-nnn SapiQ931:s1 SapiX25:s2 | Diagnostic information about the Primary Rate layer 2 (LAPD) of a CTI port. nnn' is the CTI port identifier; 's1' is the state of the Q.931 Sapi [in (inactive), dn (down), UP]; 's2' is the state of the X.25 Sapi [in (insctive), dn (down), UP]. |
| 00182 | INFO | I: CtiP-nnn SapiX25:ss | Diagnostic information about the Basic Rate layer 2 (LAPD) of a CTI port.'nnn' is the CTI port identifier; 'ss' is the state of the X.25 Sapi [in (inactive), dn (down), UP]. |
| 00183 | WARNING | W: ESB2 PCI fail | Failure in ESB2 card driver. Please report the error to the Abilis CPX Help desk. |
| 00184 | WARNING | W: ESB2 PCIS fail | Failure in ESB2 card driver. Please report the error to the Abilis CPX Help desk. |
| 00185 | WARNING | W: ESB2 JBC dd | Failure in ESB2 card driver. Please report the error to the Abilis CPX Help desk. |
| 00186 | WARNING | W: ESB2 EBIR0 fail | Failure in ESB2 card driver. Please report the error to the Abilis CPX Help desk. |
| 00187 | WARNING | W: ESB2 E-CRC fail | Failure in ESB2 card driver. Please report the error to the Abilis CPX Help desk. |
| 00188 | WARNING | W: DHCP STOPPED | Severe error in the DHCP driver related to bindings file
dchp.bnd. Please report the error to the
Abilis CPX Help desk. |
| 00189 | WARNING | W: Ospf LSA OVERFLOW | The 'LSA' table of Ospf resource reached its maximum capacity. |
| 00190 | WARNING | W: Ospf LSA DANGER ON | The 'LSA' table of Ospf resource in going in 'DANGER' state. |
| 00191 | WARNING | W: Ospf LSA DANGER OFF | The 'LSA' table of Ospf resource is exiting the 'DANGER' state. |
| 00192 | WARNING | W: Ospf ROUTE OVERFLOW | The 'ROUTE' table of Ospf resource reached its maximum capacity. |
| 00193 | WARNING | W: Ospf ROUTE DANGER ON | The 'ROUTE' table of Ospf resource is going in 'DANGER' state. |
| 00194 | WARNING | W: Ospf ROUTE DANGER OFF | The 'ROUTE' table of Ospf resource is exiting from 'DANGER' state. |
| 00195 | INFO | I: CHKDSK <drive> OK | The integrity check of the disk <drive> has been successfully executed and no errors were found. |
| 00196 | WARNING | W: CHKDSK <drive> ERRORs FOUND | The integrity check of the disk <drive> detected error(s). It is the first one of a set of messages (see System Log event 00197). Please report the error to the Abilis CPX Help desk. |
| 00197 | WARNING | W: CHKDSK ERROR: ssss | The integrity check of the disk <drive> detected the reported error 'ssss'. |
| 00198 | INFO | I: ESB2 SRC Update | Information message related to ESB2 card driver, i.e. src code should be updated. Please report the event to the Abilis CPX Help desk. |
| 00199 | WARNING | W: ESB2 OLD FW | Failure in ESB2 card driver, i.e. old firmware, ESB2 cannot be started. Please report the error to the Abilis CPX Help desk. |
| 00200 | WARNING | W: Invalid ESB | Failure in ESB2 card driver, i.e. ESB card is invalid. Please report the error to the Abilis CPX Help desk. |
| 00201 | WARNING | W: ESB2 FALC Fail1 | Failure in ESB2 card driver, i.e. troubles during the FALC configuration. Please report the error to the Abilis CPX Help desk. |
| 00202 | WARNING | W: ESB2 FALC Fail2 | Failure in ESB2 card driver, i.e. troubles during the FALC registers are not accessible. Please report the error to the Abilis CPX Help desk. |
| 00203 | WARNING | W: ESB2 FALC Fail3 | Failure in ESB2 card driver, i.e. troubles during the FALC refresh. Please report the error to the Abilis CPX Help desk. |
| 00204 | INFO | I: Sync-nnn LOOP ss | Execution on a Synchronous resource of the command for setting up the loop-back feature. 'ss' is the state of the loop-back which has been set up; 'nnn' is the Synchronous resource identifier. |
| 00205 | INFO | I: CP LOOP ss RES:Sync-nnn | Execution on a Synchronous resource of the command for setting up the loop-back feature. 'nnn' is the Synchronous resource identifier; 'ss' is the state of the loop-back which has been set up. |
| 00206 | ERROR | E: ssssss INIT ERROR | FPanel interface's initialization error messages. Please report the error to the Abilis CPX Help desk. 'ssssss' is the FPanel interface type: “FP-IDE” or “FP-LPT”. |
| 00209 | WARNING | W: EXCP TOUT | In the previous system run a sw exception occurred, but the exception handing procedure has been timed-out. Please report the error to the Abilis CPX Help desk. |
| 00210 | WARNING | W: WS TOUT | In the previous system run a request for unconditional system restart has been submitted by the user, through the WARM START command, but the procedure has been timed-out. Please report the error to the Abilis CPX Help desk. |
| 00211 | WARNING | W: RS TOUT | In the previous system run a request for system restart has been submitted by the user through the RESTART SYSTEM command, but the procedure has been timed-out. Please report the error to the Abilis CPX Help desk. |
| 00212 | INFO | I: SET BOOT VER xxxxxxxx | 'SYS SET BOOT VERSION command has been executed. At next system start-up the version 'xxxxxxxx' of the Abilis CPX sw will be loaded. |
| 00213 | WARNING | W: QFALC SSSS-NN manual restart | Manually activated hardware reset of QuadFALC of card 'SSSS-NN'. |
| 00214 | WARNING | W: QFALC SSSS-NN automatic restart | Automatically performed hardware reset of QuadFALC of card 'SSSS-NN'. |
| 00215 | WARNING | W: SWITI SSSS-NN manual restart | Manually activated hardware reset of SWITI of card 'SSSS-NN'. |
| 00216 | WARNING | W: \PKG DIR CREATE ERR-xx | The system wasn't able to create C:\PKG directory at the Abilis CPX start-up. 'xx' is the error code to be reported to the Abilis CPX Help desk. |
| 00217 | WARNING | W: ESB-nnn INT FAIL | The interface module of the ESB card 'nnn' returned an invalid type code, it is probably damaged. Please report the error to the Abilis CPX Help desk. |
| 00218 | WARNING | W: \APP DIR CREATE ERR-xx | The system wasn't able to create C:\APP directory at the Abilis CPX start-up. 'xx' is the error code to be reported to the Abilis CPX Help desk. |
| 00219 | WARNING | W: CONF RELOAD | The configuration reloading procedure has been activated. |
| 00220 | WARNING | W: CONF RELOAD ABORT | The configuration reloading procedure failed and has been aborted because of an error. |
| 00221 | INFO | I: DEBUG SIMULATE EXCEPTION | The DEBUG SIMULATE EVENT:xcp command has been executed. |
| 00222 | INFO | I: DEBUG SIMULATE WDLIVE-1 | The DEBUG SIMULATE EVENT:wdl command has been executed. |
| 00223 | WARNING | W: HFC2 JBC nn | Error in downloading firmware to HFC2 card. Please report the error to the Abilis CPX Help desk |
| 00224 | WARNING | W: SSSS-NN EEPROM Chunk:dd Code:ss | Problems for cards that use serial EEPROM for identification. The problem happens during information downloading by the driver of the card 'SSSS-NN'. The EEPROM it is probably damaged. Please report the error to the Abilis CPX Help desk. |
| 00225 | INFO | I: CtiP-nnn L1-ST:ss | This event reports diagnostic information about the layer 1 of a CTI port belonging to a POTS card. 'nnn' is the CTI port identifier;'ss' is the state of the layer 1 [ONH (the port HOOK is ON), RING (the phone is RINGING), OFFH (the port HOOK is OFF), down (the port is administratively deactivated by OPERSTATE:DOWN), stby (the port is in stand-by mode, which is a mode with limited power consumption and an automatic recovery to normal operation when telephone goes off-hook or an incoming call has to be delivered, FAIL (the port is in FAILED state, because of detected errors during the initialisation or running)]. |
| 00226 | ERROR | E: MISSING '<file-name>' | The mandatory '<file-name>' file is missing. By consequence of this the system will be restarted. Please report the event to the Abilis CPX Help desk. |
| 00227 | WARNING | W: CtiP-nnn MISSING <file-name> | This event is used only by CTI ports belonging to a POTS card, it informs that the specified country coefficient file is missing. 'nnn' is the CTI port identifier; '<file-name>' is the name of the required country coefficient file. |
| 00228 | WARNING | W: CtiP-nnn CHECKSUM FAIL | This event is used only by CTI ports belonging to a POTS card, it informs that the checksum verification fail. 'nnn' is the CTI port identifier. |
| 00229 | WARNING | W: INV RING DEF | This event is used only by a POTS card, it informs that the Ring signal definition is not valid. |
| 00230 | INFO | I: Adsl-nnn ST:ss | Diagnostic information about an Adsl resource. 'nnn' is the Adsl resource identifier; 'ss' is the Adsl resource state [ DOWN, BLCK (blocked), SYNC (synchronising), UP]. |
| 00231 | INFO | I: IpSec-nnn ST:ss | Diagnostic information about IpSec resource. 'nnn' is the IpSec resource identifier. (only value 1 is possible); 'ss' is the IpSec resource state [in (IpSec is inactive), RD (IpSec is active)]. |
| 00232 | INFO | I: Ike-nnn ST:ss/tt | Diagnostic information about IKE resource. 'nnn' is the IKE resource identifier. (only value 1 is possible); 'ss' is the IKE resource state [dn (IKE is not functioning), in (IKE administratively set inactive), RD (IKE is active), ig (IKE is executing INIT command)]; 'tt' is the IpSec resource state [dn (Ipsec is not functioning), in (IpSec administratively set inactive), RD (IpSec is active), ig (IpSec is executing INIT command)]. |
| 00233 | INFO | I: Ike-nnn HOST:h IP:x.x.x.x:y s | Diagnostic information about IKE resource. 'nnn' is the IKE resource identifier (only value 1 is possible); 's' is the IKE HOST SA state [UP ( connection opened), dn (connection closed)]. |
| 00234 | WARNING | W: SYNC-nnn Interface failure | Unsupported or defective interface module has been detected for the indicated SYNC interface. Please report the error to the Abilis CPX Help desk. 'nnn' is the SYNC resource identifier. |
| 00235 | WARNING | W: ADSL-nnn (xxx) RSTR AUTO | The specified ADSL modem has been restarted automatically as a consequence of a serious anomaly, precisely the modem stopped to respond. 'nnn' is the ADSL resource identifier. 'xxx' is the internal Abilis CPX port number, as seen through D PSTACK command. |
| 00236 | WARNING | W: ADSL-nnn STH Invalid Modem type | A modem of STH family is connected but it is not supported by Abilis CPX. 'nnn' is the ADSL resource identifier. |
| 00237 | WARNING | W: ETH-nnn Failed Reset | An attempt to reset the indicated ETH interface failed. 'nnn' is the ETH resource identifier. |
| 00238 | WARNING | W: ETH-nnn Filter Overflow | The MAC addresses filter table needed for IEEE bridge functionality was saturated. 'nnn' is the ETH resource identifier. |
| 00239 | INFO | I: ETH-nnn Limited Auto Mode | This event should not happen, it is reserved to development process. 'nnn' is the ETH resource identifier. |
| 00240 | WARNING | W: cccc-nnn DELIC DWNL FAIL eee | Failure during the download of firmware into DELIC chip of BRI4 and BRI8 cards. It must be reported to the Abilis CPX help-desk. 'cccc' is the type of the card, either BRI4 or BRI8; 'nnn' is the BRI4 or BRI8 card identifier; 'eee' is the internal error code. |
| 00241 | WARNING | W: POTS-nnn 12V Absent | 12V voltage is not supplied to the indicated POTS card. 'nnn' is the POTS card identifier. |
| 00242 | INFO | I: cccc-nnn DSP:xx DWNL OK | Successful download of firmware into indicated DSP. 'cccc' is type of the card where DSP is hosted; 'nnn' is the card identifier where DSP is hosted; 'xx' is the DSP identifier on the specified card. |
| 00243 | INFO | I: cccc-nnn DSP:xx DWNL KR FAIL | Kernel download failure for the indicated DSP. 'cccc' is type of the card where DSP is hosted; 'nnn' is the card identifier where DSP is hosted; 'xx' is the DSP identifier on the specified card. |
| 00244 | INFO | I: cccc-nnn DSP:xx DWNL PR FAIL | Program download failure for the indicated DSP. 'cccc' is type of the card where DSP is hosted; 'nnn' is the card identifier where DSP is hosted; 'xx' is the DSP identifier on the specified card. |
| 00245 | INFO | I: cccc-nnn DSP:xx RSTR USER | Manual restart of the indicated DSP through R CTIAC command. 'cccc' is type of the card where DSP is hosted; 'nnn' is the card identifier where DSP is hosted; 'xx' is the DSP identifier on the specified card. |
| 00246 | INFO | I: cccc-nnn DSP:xx RSTR AUTO | The occurrence of an automatic restart of the indicated DSP as a consequence of a DSP blockage automatically detected. 'cccc' is type of the card where DSP is hosted; 'nnn' is the card identifier where DSP is hosted; 'xx' is the DSP identifier on the specified card. |
| 00247 | INFO | I: cccc-nnn DSP:xx RSTR FAIL | The automatic restart of DSP did not succeed three time consecutively, and DSP is permanently put in failed state. 'cccc' is type of the card where DSP is hosted; 'nnn' is the card identifier where DSP is hosted; 'xx' is the DSP identifier on the specified card. |
| 00248 | INFO | I: USB PCIxx/yy tttt aaaa ii | This event indicates recognised USB controllers, I/O mapped. 'xx' is the PCI SlotId of the controller, as shown with D PCIDEV command; 'yy' is the PCI Function of the controller, as shown with D PCIDEV command; 'tttt' is the type of controller, which can be OHCI, UHCI or EHCI; 'aaaa' is I/O address at which controller is accessible; 'ii' is the IRQ assigned to the controller. |
| 00249 | INFO | I: USB PCIxx/yy tttt aaaaaaaa ii | This event indicates recognised USB controllers, memory mapped. 'xx' is the PCI SlotId of the controller, as shown with D PCIDEV command; 'yy' is the PCI Function of the controller, as shown with D PCIDEV command; 'tttt' is the type of controller, which can be OHCI, UHCI or EHCI; 'aaaaaaaa' is memory address at which controller is accessible; 'ii' is the IRQ assigned to the controller. |
| 00250 | INFO | I: USB PCIxx/yy Failure | Failure in the operation with the indicated USB controller. 'xx' is the PCI SlotId of the controller, as shown with D PCIDEV command; 'yy' is the PCI Function of the controller, as shown with D PCIDEV command. |
| 00251 | WARNING | W: LDM Corrupted, LDM Cleared | A content corruption occurred for the debug log in memory. The log had to be cleared in order to recover from the error. |
| 00252 | INFO | I: Smtp-1 ST:ssss | SMTP Server resource state information. 'ssss' is the resource state [RD (ACTIVE), in (INACTIVE)]. |
| 00253 | INFO | I: Pop3-1 ST:ssss | POP3 Server resource state information. 'ssss' is the resource state [RD (ACTIVE), in (INACTIVE)]. |
| 00254 | INFO | I: POWER ON | WDG detects that in the previous run CPX was switched off. |
| 00255 | INFO | I: WATCHDOG xx | Hw Interface initialisation/detection success notification. 'xx' identifies the Front Panel/WatchDog interface type. |
| 00256 | WARNING | W: ABNORMAL SYSTEM REBOOT | SYSTEM was abnormal rebooted; LIVE state was detected during boot phase. |
| 00257 | INFO | I: SYSTEM LOG CLEARED | System log clearing event; i.e. C L command was issued. |
| 00258 | INFO | I: PoeCli-nnn ST:ssss | Diagnostic information: PoeCli resource. 'nnn' is the resource identifier; 'ssss' is the resource state [dn (DOWN), RD (READY)] |
| 00259 | INFO | I: PoeAc-nnn ST:ssss | Diagnostic information: PoeAc resource. 'nnn' is the resource identifier; 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE), ee (ETH-ERROR)] |
| 00260 | WARNING | W: WATCHDOG DISABLED | Watchdog is disabled. |
| 00261 | WARNING | W: WATCHDOG NOT DRIVEN | Watchdog is not driven. |
| 00262 | INFO | I: CPX LIGHT EDITION | CPX is running its Light edition. |
| 00264 | INFO | I: CtiGkc-1 ST:ssss | Diagnostic information about CtiGkc resource. |
| 00265 | INFO | I: CtiIax-1 ST:ssss | Diagnostic information about CtiIax resource. 'ssss' is the resource state [in (INACTIVE), AC (ACTIVE)]. |
| 00266 | INFO | I: CtiDisa-1 ST:ssss | Diagnostic information about CtiDisa resource. 'ssss' is the resource state [in (INACTIVE), AC (ACTIVE)]. |
| 00267 | INFO | I: CtiP-nnn VOICE-ST:sss1 PDN-ST:sss2 | Diagnostic information about CTI port belonging to CELL (GSM/UMTS) card. 'nnn' is the Cti port number. |
| 00268 | INFO | I: Radius-1 ST:ssss | Diagnostic information about Radius resource. 'ssss' is the resource state [dn (DOWN), in (INACTIVE), RD (ACTIVE)]. |
| 00269 | INFO | I: Vrrp-1 ST:ssss | Diagnostic information about Vrrp resource. 'ssss' is the resource state [dn (DOWN), in (INACTIVE), RD (ACTIVE)]. |
| 00270 | INFO | I: Ip-nnn ST:sss1 LINK:sss2 | Diagnostic information about IP resource. 'nnn' is the resource identifier; 'sss1' is the main resource state [DN (DOWN), UP (UP), gU (GOING-UP), gD (GOING-DOWN)]; 'sss2' is the link state [ld (LINKDOWN), LR (LINKREADY), ln (LINKNOTPRESENT), RD (X25READY), cg (X25CALLING), cd (X25CALLED), CN (X25CONNECTED), dl (X25DELAY), wt (X25WAITING), ht (HALTED), fl (FAILED)]. |
| 00271 | INFO | I: CtiSip-1 ST:ssss | Diagnostic information about CtiSip resource. 'ssss' is the resource state [in (INACTIVE), AC (ACTIVE)]. |
| 00272 | INFO | I: Stun-1 ST:ssss | Diagnostic information about Stun resource. 'ssss' is the resource state [in (INACTIVE), RD (READY)]. |
| 00273 | WARNING | W: USB autoreset parent hub of xxx | USB Reset of device's parent hub; 'xxx' is the number of USB port. |
| 00274 | WARNING | W: USB unavailable parent hub of xxx | USB Unavailable device's parent hub; 'xxx' is the number of USB port. |
| 00275 | INFO | I: TRACE AUTO SAVE: STARTED | Automatic tracer saving feature: the trace has started. |
| 00276 | WARNING | W: TRACE AUTO SAVE: TSAVE:NO | Automatic tracer saving feature: the
TSAVE parameter is set to NO. |
| 00277 | WARNING | W: TRACE AUTO SAVE: REQ CANCELLED | Automatic tracer saving feature: the trace has received a request for cancellation. |
| 00278 | WARNING | W: TRACE AUTO SAVE: TRACE NOTRUNNING | Automatic tracer saving feature: the trace is not running. |
| 00279 | INFO | I: TRACE AUTO SAVE: TRACE STOPPED | Automatic tracer saving feature: the trace has been stopped. |
| 00280 | INFO | I: TRACE AUTO SAVE: TRACE SAVED | Automatic tracer saving feature: the trace has been saved. |
| 00281 | WARNING | W: TRACE AUTO SAVE: TRACE NOT SAVED | Automatic tracer saving feature: the trace has not been saved. |
| 00282 | INFO | I: TRACE AUTO SAVE: TRACE EMPTY | Automatic tracer saving feature: the trace is empty. |
| 00283 | INFO | I: TRACE AUTO SAVE: TRACE RE-STARTED | Automatic tracer saving feature: the trace has been restarted. |
| 00284 | INFO | I: DEBUG SIMULATE TRACE AUTO SAVE | The DEBUG SIMULATE EVENT:tsave command has been executed. |
| 00285 | WARNING | W: CTIR DISABLED | The DISABLE CTIR command has been executed. |
| 00286 | INFO | I: CTIR ENABLED | The ENABLE CTIR command has been executed. |
| 00287 | WARNING | W: AC DISABLED | The DISABLE AC command has been executed. |
| 00288 | INFO | I: AC ENABLED | The ENABLE AC command has been executed. |
| 00289 | INFO | I: UpnpC-1 ST:ssss | Diagnostic information about UpnpC resource. 'ssss' is the resource state [in (INACTIVE), RD (READY)]. |
| 00290 | INFO | I: UpnpS-1 ST:ssss | Diagnostic information about UpnpS resource. 'ssss' is the resource state [in (INACTIVE), RD (READY)]. |
| 00291 | INFO | I: DSP test start | DSP Test: Start test. |
| 00292 | INFO | I: DSP test end | DSP Test: End test. |
| 00293 | WARNING | W: cccc-nnn DSP#n ssss recover | DSP Test: Recovery attempt. 'cccc' is type of the card and 'nnn' is the card identifier. |
| 00294 | WARNING | W: cccc-nnn DSP#n ssss bad | DSP Test: DSP failure. 'cccc' is type of the card and 'nnn' is the card identifier. |
| 00295 | WARNING | W: CELL-nnn - AT RX garbage XX | CELL message, AT RX garbage 1. |
| 00296 | WARNING | W: CELL-nnn - AT RX garbage | CELL message, AT RX garbage 2. |
| 00297 | WARNING | W: CELL-nnn - SHUTDOWN DD | CELL message, SHUTDOWN URC on GSM detected. |
| 00298 | WARNING | W: CELL-nnn - PIN STATE FAIL | CELL message, PIN state fail on UMTS detected. |
| 00299 | WARNING | W: CELL-nnn - UNKNOWN DISC REASON DD | CELL message, UNKNOWN disconnect reason. |
| 00300 | WARNING | W: CELL-nnn - PUK REQUIRED | CELL message, PUK required CME error. |
| 00301 | WARNING | W: CELL-nnn - Invalid PIN | CELL message, INVALID PIN CME error. |
| 00302 | WARNING | W: CELL-nnn - Invalid PIN2 | CELL message, INVALID PIN2 CME error. |
| 00303 | WARNING | W: CELL-nnn - Invalid PUK | CELL message, INVALID PUK CME error. |
| 00304 | WARNING | W: CELL-nnn - Invalid PUK2 | CELL message, INVALID PUK2 CME error. |
| 00305 | INFO | I: Opc-1 ST:ssss | Diagnostic information about Opc resource. 'ssss' is the resource state [DN (DOWN), UP]. |
| 00306 | INFO | I: SysLog-1 ST:ssss | Diagnostic information about SysLog resource. 'ssss' is the resource state [in (INACTIVE), RD (READY)]. |
| 00307 | INFO | I: Rjs-nnn ST:sss1 USB-ST:sss2 | Diagnostic information about Rjs resource. 'nnn' is the resource identifier; 'sss1' is the resource state [DN (DOWN), UP, in (INACTIVE)]; 'sss2' is the USB state [ ds (DISCONNECTED), CN (CONNECTED)]. |
| 00308 | WARNING | W: cccc-nnn ssss FW - C:n.m - R:x.y | C64xx error, incorrect FW version. 'cccc' is type of the card and 'nnn' is the card identifier. |
| 00309 | WARNING | W: cccc-nnn ssss FW missing | C64xx error, missing FW. 'cccc' is type of the card and 'nnn' is the card identifier. |
| 00310 | WARNING | W: cccc-nnn ssss FW damaged | C64xx error, FW damaged - not BIH file. 'cccc' is type of the card and 'nnn' is the card identifier. |
| 00311 | WARNING | W: cccc-nnn C64xx FW Init failed | C64xx error, initialisation failed. 'cccc' is type of the card and 'nnn' is the card identifier. |
| 00312 | WARNING | W: cccc-nnn FPGA FW missing | QPRIX error, missing FPGA FW. 'cccc' is type of the card and 'nnn' is the card identifier. |
| 00313 | WARNING | W: cccc-nnn C64xx CCB Init failed | QPRIX error, CCB initialisation failed. 'cccc' is type of the card and 'nnn' is the card identifier. |
| 00314 | WARNING | W: cccc-nnn C64xx PCM Init failed | QPRIX error, PCM initialisation failed. 'cccc' is type of the card and 'nnn' is the card identifier. |
| 00315 | INFO | I: SimBox-nnn ST:sss1 USB-ST:sss2 | Diagnostic information about SimBox resource. 'nnn' is the resource identifier; 'sss1' is the resource state [DN (DOWN), UP, in (INACTIVE)]; 'sss2' is the USB state [ ds (DISCONNECTED), CN (CONNECTED)]. |
| 00316 | ERROR | W: cccc-nnn C64xx IQ overflow | QPRIX error, interrupt queue overflow. 'cccc' is type of the card and 'nnn' is the card identifier. |
| 00317 | INFO | CONF:MOVED DRIVERS.CFG TO DRIVERS.BAD | Corrupted Configuration file copied to DRIVERS.BAD file. |
| 00318 | INFO | I: Gps-nnn ST:sss1 USB-ST:sss2 | Diagnostic information about Gps resource. 'nnn' is the resource identifier; 'sss1' is the resource state [DN (DOWN), UP, in (INACTIVE)]; 'sss2' is the USB state [ ds (DISCONNECTED), CN (CONNECTED)]. |
| 00321 | WARNING | W: <user>-in.log CORRUPTED | The Incoming Calls log file of the specified user <user> is corrupted. |
| 00322 | WARNING | W: <user>-in.log DELETED | The Incoming Calls log file of the specified user <user> was deleted. |
| 00323 | WARNING | W: <user>-out.log CORRUPTED | The Outgoing Calls log file of the specified user <user> is corrupted. |
| 00324 | WARNING | W: <user>-out.log DELETED | The Outgoing Calls log file of the specified user <user> was deleted. |
| 00325 | INFO | I: Gpio-nnn ST:sss1 USB-ST:sss2 | Diagnostic information about Gpio resource. 'nnn' is the resource identifier; 'sss1' is the resource state [DN (DOWN), UP, in (INACTIVE)]; 'sss2' is the USB state [ ds (DISCONNECTED), CN (CONNECTED)]. |
| 00326 | INFO | I: GpioPc-nnn ST:ssss | Diagnostic information about GpioPc resource. 'nnn' is the resource identifier; 'ssss' is the resource state [DN (DOWN), UP] |
| 00327 | INFO | I: CtiSms-1 ST:ssss | Diagnostic information about CtiSms resource. 'ssss' is the resource state [ dn (INACTIVE), RD (ACTIVE)] |
| 00328 | INFO | W: cccc-nnn FPGA FW - C:n.m - R:x.y | QPRIX error, incorrect FPGA FW version. 'cccc' is type of the card and 'nnn' is the card identifier. |
| 00329 | ERROR | E: EEC open - XX - ssss | Echo canceler channel open fail. |
| 00330 | INFO | I: Sntp-1 CLI-ST:ssss | Diagnostic information about Sntp resource, where 'ssss' is the SNTP client state [in (INACTIVE), dn (ACTIVE), RD (READY), dg (DISCONNECTING), hl (HALTED), ds (DISABLED)]. |
| 00331 | WARNING | W: cccc-nnn FPGA init failed | HFC3 error, cannot init (upload FW) FPGA (SWIX). 'cccc' is type of the card and 'nnn' is the card identifier. |
| 00332 | WARNING | W: \LICENCE DIR CREATE ERR-XX | System wasn't able to create C:\LICENCE directory at start-up. |
| 00336 | WARNING | W: FW UPLOAD START XXXX XXXX ssss | USB BootLoader, FW Update started. |
| 00337 | WARNING | W: FW UPLOAD SUCCESS XXXX XXXX ssss | USB BootLoader, FW Update success. |
| 00338 | WARNING | W: FW UPLOAD FAILURE XXXX XXXX ssss | USB BootLoader, FW Update failure. |
| 00339 | WARNING | W: FW MISSING <file-name> | USB BootLoader, FW <file-name> file is missing. |
| 00340 | WARNING | W: FW UPLOAD REQUEST XXXX XXXX ssss | USB BootLoader, FW Update request. |
| 00341 | WARNING | W: FW UPLOAD REQUEST SUCCESS XXXX XXXX ssss | USB BootLoader, FW Update request success. |
| 00342 | WARNING | W: FW UPLOAD REQUEST FAIL XXXX XXXX ssss | USB BootLoader, FW Update request fail. |
| 00343 | WARNING | W: FW UPLOAD SKIPPED XXXX XXXX ssss | USB BootLoader, FW Update skipped. |
| 00344 | INFO | I: Ip-nnn ST:sss1 LINK:ssss2 PING:sss3 | Diagnostic information about IP resources. 'nnn' is the resource identifier; 'sss1' is the main resource state [DN (DOWN), UP (UP), gU (GOING-UP), gD (GOING-DOWN)]; 'sss2' is the link state [ld (LINKDOWN), LR (LINKREADY), ln (LINKNOTPRESENT), RD (X25READY), cg (X25CALLING), cd (X25CALLED), CN (X25CONNECTED), dl (X25DELAY), wt (X25WAITING), ht (HALTED), fl (FAILED)] and 'sss3' is the ping state [DN (DOWN), UP, UN (UNKNOWN)]. |
| 00345 | INFO | I: Dhcp-1 ST:ssss | Diagnostic information about Dhcp resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE), st (STOPPED)]. |
| 00346 | INFO | I: DhcpC-1 ST:ssss | Diagnostic information about DhcpC resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE)]. |
| 00347 | ERROR | E: USB EXIT MSG: ssss | USB fatal exit, 'ssss' is the reported error message. |
| 00348 | ERROR | E: USB EXIT CODE: nnnn | USB fatal exit, 'nnnn' it the reported error code. |
| 00349 | INFO | I: Ddns-1 ST:ssss | Diagnostic information about Ddns resource. 'ssss' is the resource state [RD (READY), in (INACTIVE)]. |
| 00350 | INFO | I: TIME CHANGE, from UTC to LOCAL time | Time service information: change from UTC to LOCAL time. |
| 00351 | INFO | I: TIME CHANGE, S T comand executed | Time service information, S T comand executed. |
| 00352 | INFO | I: LOCAL vs. RTC resyn, Delta > 1 min.(nn sec.) | Time service information, RTC resyncronisation. |
| 00353 | INFO | I: LOCAL vs. RTC resyn done | Time service information, RTC resyncronisation done. |
| 00354 | INFO | I: Upgrade from version prior to 7.0.0 | Time service information, detected upgrade from ver. < 7.0.0. |
| 00355 | INFO | I: CMOS clock changed from LOCAL to UTC time | Time Service information, CMOS clock changed from LOCAL to UTC time |
| 00356 | INFO | I: C:\TIMECFG.DAT missing, indicated time is UTC | Time Service information, C:\TIMECFG.DAT file is missing. |
| 00357 | INFO | I: TIME CHANGE, from <zone1> to <zone2> time zone | Time Service information, time zone changed from <zone1> to <zone2> time zone. |
| 00358 | INFO | LINUX WARM START | System warm start, requested by LINUX OS. |
| 00359 | INFO | SHUTDOWN | System shutdown, requested by Abilis CPX. |
| 00360 | INFO | LINUX SHUTDOWN | System shutdown, requested by LINUX OS. |
| 00361 | ERROR | E: MFPCI or MFIDE3(FW Rev. >= 28) is required | Incorrect Hw interface (WatchDog, LCD display, ...) found. |
| 00362 | INFO | I: WATCHDOG MFIDE3 FW Rev. nnn | MFIDE3 firmware version report. |
| 00363 | ERROR | E: MFIDE3 FW Rev. 28 or higher is required | Incorrect MFIDE3 firmware version. |
| 00364 | INFO | I: Rsim-nnn ST:ssss | Diagnostic information about RSim resource. 'nnn' is the Rsim resource identifier. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE)]. |
| 00365 | INFO | I: DEBUG SIMULATE BLOCKAGE | The DEBUG SIMULATE EVENT:blockage command has been executed. |
| 00366 | WARNING | W: LICENCE, FILE MISSING | Licence not activated because the licence file is missing. |
| 00367 | WARNING | W: LICENCE, FILE CORRUPTED | Licence not activated because the licence file content is not valid. |
| 00368 | WARNING | W: LICENCE, ABILIS-ID MISMATCH | Licence not activated because Abilis ID reported in the licence file is not valid. |
| 00369 | WARNING | W: LICENCE, EXPIRED | Licence not activated because it is expired. |
| 00370 | WARNING | W: LICENCE, LOAD ERROR XXXX (ssss) | Licence not specified error. 'xxxx' is the error code and 'ssss' is the raw description. |
| 00371 | INFO | I: LICENCE, LOADED | Licence successfully activated. |
| 00372 | ERROR | E: MISSING 'VMX' LICENCE | Missing VMX Licence error message. |
| 00373 | INFO | W: LICENCE, rrrr-nnn NOT ACTIVATED | Not licenced resource warning message, where 'rrrr' is the resource type and 'nnn' is the resource identifier. |
| 00374 | INFO | W: LICENCE, <service> DISABLED | Not licenced service warning message: the specified <service> service was disabled. |
| 00375 | INFO | W: LICENCE, IKE HOSTs NUMBER CHANGED | IKE HOSTs number changed: the parameter 'max-hosts' has been set equal to IKEHOSTS licence value. |
| 00376 | INFO | AUTO SAVE FAIL, RC:XX (ssss) | Auto-save of configuration file failure. 'xxxx' is the error code and 'ssss' is the raw description. |
| 00377 | WARNING | W: <user>-in.log BAD VERSION | The Incoming Calls log file of the specified user <user> has invalid version. |
| 00378 | WARNING | W: <user>-in.log CONVERTED | The Incoming Calls log file of the specified user <user> was converted to the currect version. |
| 00379 | WARNING | W: <user>-out.log BAD VERSION | The Outgoing Calls log file of the specified user <user> has invalid version. |
| 00380 | WARNING | W: <user>-out.log CONVERTED | The Outgoing Calls log file of the specified user <user> was converted to the currect version. |
| 00381 | WARNING | W: CTIR DB overflow. | CTIR internal DB overflow. |
| 00382 | WARNING | W: cccc-nnn, Debug mode, FW not downloaded | QPRIX debug mode, FW not downloaded. 'cccc' is type of the card and 'nnn' is the card identifier. |
| 00383 | WARNING | W: cccc-nnn, C64xx channel config failed | QPRIX Channel configuration. 'cccc' is type of the card and 'nnn' is the card identifier. |
| 00384 | WARNING | W: Ip-nnn NAT ALIAS networks overflow | Ip resource: NAT ALIAS networks overflow. 'nnn' is the Ip resource identifier. |
| 00385 | WARNING | W: Ip-nnn VIRTUAL secondary networks overflow | Ip resource: VIRTUAL SECONDARY networks overflow. 'nnn' is the Ip resource identifier. |
| 00386 | WARNING | W: Ip-nnn VRRP networks overflow | Ip resource: VRRP VIRTUAL networks overflow. 'nnn' is the Ip resource identifier. |
| 00387 | INFO | I: Adsl-nnn ST:ssss TX/RX:xxxx/yyyy | Diagnostic information about Adsl resource. 'nnn' is the Adsl resource identifier. 'ssss' is the resource state [DOWN, BLCK (BLOCKED), SYNC (SYNCHRONISING), UP, FAIL, TEST, RTN (RETAIN)]. 'xxxx' and 'yyyy' are transmission and reception speeds. |
| 00388 | INFO | I: Tftp-1 ST:ssss | Diagnostic information about Tftp resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE)]. |
| 00389 | INFO | I: Alarm-1 ST:ssss | Diagnostic information about Alarm resource. 'ssss' is the resource state [RD (READY), in (INACTIVE)]. |
| 00390 | INFO | I: CtiVm-1 ST:ssss | Diagnostic information about CtiVm resource. 'ssss' is the resource state [RD (READY), in (INACTIVE)]. |
| 00391 | INFO | I: CtiVr-1 ST:ssss | Diagnostic information about CtiVr resource. 'ssss' is the resource state [RD (READY), in (INACTIVE)]. |
| 00392 | INFO | I: IpSh-1 ST:ssss | Diagnostic information about IpSh resource. 'ssss' is the resource state [dn (DOWN), RD (READY)]. |
| 00393 | ERROR | E: USB EXIT THREAD: nnn | USB fatal thread: 'nnn' is the thread active at the moment of the problem. |
| 00394 | INFO | I: DEBUG SIMULATE WDG RESET | The DEBUG SIMULATE EVENT:wdgreset command has been executed. |
| 00395 | INFO | I: WDG RESET INEFFECTIVE | The DEBUG SIMULATE EVENT:wdgreset command has been executed but the WDG reset hadn't effect. |
| 00396 | INFO | I: Vrrp-1 Router ID:nnn I-ST:sss1 ST:sss2 | Vrrp Router state report. |
| 00397 | ERROR | E: POTS32-nnn failure. V-Maillbox unable to reset | V-Mailbox blocked (busy after two resets) |
| 00398 | INFO | I: ABILIS CPX Ver. nnnn - Build mmmm | Running Abilis CPX version/build. |
| 00399 | INFO | I: CtiP-nnn VOICE-ST:sss1 CITO:sss2 AUDIO:sss3 | Diagnostic information about CTI port belonging to CITO card. |
| 00400 | WARNING | W: '<file-name>' '<error>' | The reported '<error>' occurred during the '<file-name>' file treatment. Please report the event to the Abilis CPX Help desk. |
| 00401 | INFO | I: Ldap-1 ST:ssss | Diagnostic information about Ldap resource. 'ssss' is the resource state [RD (READY), in (INACTIVE)]. |
| 00402 | INFO | I: DEBUG SIMULATE LOOP 'nnn' msec | The DEBUG SIMULATE EVENT:loop command has been executed. |
| 00403 | ERROR | W: cccc-nnn C64xx IQ reset successful | QPRIX error, interrupt queue reset successful. 'cccc' is type of the card and 'nnn' is the card identifier. |
| 00404 | ERROR | W: cccc-nnn C64xx IQ reset unsuccessful | QPRIX error, interrupt queue reset unsuccessful. 'cccc' is type of the card and 'nnn' is the card identifier. |
| 00405 | WARNING | W: '<file-name>' '<error>' [nn] - ssss | The reported '<error>' occurred during the '<file-name>' file treatment. The number 'nn' is the occurred File System error code and 'ssss' is the related description. Please report the event to the Abilis CPX Help desk. |
| 00406 | INFO | I: Trfa-1 ST:ssss | Diagnostic information about Trfa resource. 'ssss' is the resource state [RD (READY), in (INACTIVE)]. |
| 00407 | INFO | I: Rip-1 ST:ssss | Diagnostic information about Rip resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE)]. |
| 00408 | INFO | I: Dns-1 ST:ssss | Diagnostic information about Dns resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE)]. |
| 00409 | INFO | I: X509-1 ST:ssss | Diagnostic information about X509 resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE), ig (INIT)]. |
| 00410 | INFO | I: Ssl-1 ST:ssss | Diagnostic information about Ssl resource. 'ssss' is the resource state [dn (DOWN), RD (READY)]. |
| 00411 | INFO | I: Nat-1 ST:ssss | Diagnostic information about Nat resource. 'ssss' is the resource state [dn (DOWN), RD (READY)]. |
| 00412 | INFO | I: Snmp-1 ST:ssss | Diagnostic information about Snmp resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE), dg (DISCONNECTING), hl (HALTED)]. |
| 00413 | INFO | I: Http-1 ST:ssss | Diagnostic information about Http resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE)]. |
| 00414 | INFO | I: Acnt-1 ST:ssss | Diagnostic information about Acnt resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE)]. |
| 00415 | INFO | I: Ospf-1 ST:ssss | Diagnostic information about Ospf resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE)]. |
| 00416 | INFO | I: Mail Service filtering FIFO overflow (nn/NN) | Mail Service informations about the mail filtering FIFO overflow. 'nn' is the number of queued mails and 'NN' is the queue size. |
| 00417 | WARNING | W: OPC USER:<user> Table OVERFLOW | OPC has an USER table overflow state. |
| 00418 | WARNING | W: OPC USER:<user> CALL Table OVERFLOW | OPC has a CALL table overflow state. |
| 00419 | WARNING | W: OPC USER:<user> CALL-QUEUE Table OVERFLOW | OPC has a CALL QUEUE table overflow state. |
| 00420 | WARNING | W: WATCHDOG INVALID WDR VALUE, 0xHH | Hw interface, WatchDog: invalid WDG register value. Please report the event to the Abilis CPX Help desk. |
| 00421 | WARNING | W: CHKDSK <drive> ABORTED | The execution of integrity check of the disk <drive> exceeded the timed-out of 5 sec. has beeen aborted. |
| 00422 | WARNING | W: CHKDSK <drive> ERROR [nn] - ssss | An error occurred during the execution of integrity check of the disk <drive>. The number 'nn' is the occurred error code and 'ssss' is the related description. Please report the event to the Abilis CPX Help desk. |
| 00423 | INFO | W: LICENCE, SWAC CHANs NUMBER CHANGED | The CTISYS parameter 'swac-chans' value has been changed: it has been set equal to SWAC (Software Audio Compressor) licence value. |
| 00424 | INFO | I: Tcp-nnn ST:ssss | Diagnostic information about Tcp resource. 'ssss' is the resource state [dn (DOWN), RD (READY)]. |
| 00425 | INFO | I: Udp-nnn ST:ssss | Diagnostic information about Udp resource. 'ssss' is the resource state [dn (DOWN), RD (READY)]. |
| 00426 | INFO | I: Telnet-nnn ST:ssss | Diagnostic information about Telnet resource. 'ssss' is the resource state [dn (DOWN), RD (READY)]. |
| 00427 | INFO | I: Ssh-nnn ST:ssss | Diagnostic information about SSh resource. 'ssss' is the resource state [dn (DOWN), RD (READY)]. |
| 00428 | INFO | I: MFIo-nnn ST:ssss | Diagnostic information about MfIo resource. 'ssss' is the resource state [in (INACTIVE), RD (ACTIVE)]. |
| 00429 | WARNING | W: LDAP - <file-name> version update required, from v. xxx to v. yyy | LDAP service need to update db file <file-name>. |
| 00430 | WARNING | W: LDAP - <file-name-1> v. xxx being saved in <file-name-2> | LDAP service, db file <file-name> save is in progress. |
| 00431 | WARNING | W: LDAP - <file-name-1> v. xxx saved in <file-name-2> | LDAP service, db file <file-name> successfully saved. |
| 00432 | WARNING | W: LDAP - Error nn (ssss) saving <file-name>. | LDAP service, db file <file-name> unsuccessful save. The number 'nn' is the occurred error code and 'ssss' is the related description. Please report the event to the Abilis CPX Help desk. |
| 00433 | WARNING | W: LDAP - <file-name> being updated to v. xxx | LDAP service, db file <file-name> version update is in progress. |
| 00434 | WARNING | W: LDAP - <file-name> successfully updated to v. xxx | LDAP service, db file <file-name> successfully updated. |
| 00435 | WARNING | W: LDAP - Error nn (ssss) updating <file-name> | LDAP service, db file <file-name> unsuccessful update. The number 'nn' is the occurred error code and 'ssss' is the related description. Please report the event to the Abilis CPX Help desk. |
| 00436 | INFO | I: MfTemp-nnn ST:ssss | Diagnostic information about MfTemp resource. 'ssss' is the resource state [in (INACTIVE), RD (ACTIVE)]. |
| 00437 | INFO | I: SysCtl-nnn ST:ssss | Diagnostic information about SysCtl resource. 'ssss' is the resource state [in (INACTIVE), RD (ACTIVE)]. |
| 00438 | WARNING | W: MAIL SERVICE SMTP ERROR [nn] - ssss | Mail Service: mail not sent because of SMTP driver error. The number 'nn' is the occurred error code and 'ssss' is the related description. Please report the event to the Abilis CPX Help desk. |
| 00439 | WARNING | W: MAIL SERVICE ERROR [nn] - ssss | Mail Service: mail not sent because of service internal error. The number 'nn' is the occurred error code and 'ssss' is the related description. Please report the event to the Abilis CPX Help desk. |
| 00440 | WARNING | W: Adsl-nnn STH Unsupported FW version | ADSL (STH) modem - unsupported FW version. 'nnn' is the resource identifier. |
| |  | |
| Chapter 78. Log messages |  | Chapter 79. Disconnection codes |