25.1. IPRTR resource

The IPRTR (IP Router) resource is used within the Abilis CPX to route IP datagrams between LAN and WAN ports.

IP Datagram transport on LAN is carried out using Ethernet or Token Ring protocols.

IP Datagram transport on WAN is carried out using X.25 resource (obsolete) or non-X.25 resources (LAPB, IP Tunnel or PPP links).

25.1.1. IPRTR resource parameters

Use the following command to display the parameters of the resource. By typing d p iprtr ? command it's possible to display the meaning of all the parameters.

[17:50:56] ABILIS_CPX:d p iprtr

RES:Iprtr ---------------------------------------------------------------------
Run    DESCR:IP_Router_general_properties
       - General --------------------------------------------------------------
       R-ID:080.080.180.80          NAT:OUTSIDE
       maxroute:500       DFTTTL:255          ps:2048       
       DEF-LOCAL-AD:0     DEF-STATIC-AD:1     DEF-OSPF-AD:110   DEF-RIP-AD:120
       pvc:0              bsvc:0              LINKS:6           virtual:2
       - IP Access List -------------------------------------------------------
       ACL:YES                ACLBYPASS:#              
       COS:ENABLED            COSDFT:LOW        
       COSBALANCE:NO          NORMRATE:50            LOWRATE:50   
       - IPCOS to 802.1q (VLAN) priority --------------------------------------
       LOW:0                  NORMAL:0               HIGH:0    
       - Ppp-Dns --------------------------------------------------------------
       PPP-DNS-PRI:000.000.000.000  PPP-DNS-SEC:000.000.000.000

Meaning of the most important parameters:

R-ID

It shows the Router ID address [AUTO: it's the default value and it's obtained considering the first IP resource of the homonym table, whose address is not 0.0.0.0; 1-126.x.x.x, 128-223.x.x.x: it's used a specific IP].

NAT

It indicates the side of the IPRTR when remote hosts connect to R-ID IP address. This information is required by NAT in order to determine if the IP address must be translated or not. This parameter can be set only when R-ID is not set to AUTO [NO: NAT is not configured; INSIDE: the R-ID address is in the INSIDE IP resource; OUTSIDE: the R-ID address is in the OUTSIDE IP resource, VPN: the R-ID address is in the VPN IP resource, DMZ: the R-ID address is in the DMZ IP resource].

maxroute

Maximum number of routings in the routing table [100..10000].

DFTTTL

Default TTL value when transport layer doesn't provide one [1..255].

PS

Packet size [16..2048 bytes].

DEF-LOCAL-AD

Default administrative distance for local-connected routes [0..255].

DEF-STATIC-AD

Default administrative distance for static routes [0..255].

DEF-OSPF-AD

Default administrative distance for OSPF routes [0..255].

DEF-RIP-AD

Default administrative distance for RIP routes [0..255].

pvc

Number of PVC interfaces (Read Only).

bsvc

Number of BSVC interfaces (Read Only).

LINKS

Number of LINK/LAN/PPP interfaces (Read Only).

virtual

Number of VIRTUAL interfaces (Read Only).

ACL

Access list activation mode [NO, YES].

ACLBYPASS

Source/destination IP address that bypasses the Access list [*, #, 1-126.x.x.x, 127.0.0.1, 128-223.x.x.x].

COS

Enable/Disable class-of-service management [DISABLED, ENABLED].

COSDFT

Class-of-service Default value [HIGH, NORMAL, LOW].

COSBALANCE

Class-of-service balancing activation [NO, YES].

NORMRATE

NORMAL vs. HIGH class-of-service balancing percentage [0..100].

LOWRATE

LOW vs. NORMAL class-of-service balancing percentage [0..100].

LOW

LOW class-of-service to 802.1q (VLAN) priority [0..7].

NORMAL

NORMAL class-of-service to 802.1q (VLAN) priority [0..7].

HIGH

HIGH class-of-service to 802.1q (VLAN) priority [0..7].

PPP-DNS-PRI

Primary DNS provided by local PPPs to remote PPPs [0.0.0.0, 1-126.x.x.x, 127.0.0.1, 128-223.x.x.x].

PPP-DNS-SEC

Secondary DNS provided by local PPPs to remote PPPs [0.0.0.0, 1-126.x.x.x, 127.0.0.1, 128-223.x.x.x].

The following command allows the administrator to change the configuration of the resource:

s p iprtr parameter:value...

[Caution]Caution

To activate the changes made on the upper case parameters, execute the initialization command init res:iprtr; while to set act the changes made on the lowercase parameters a save conf and an Abilis restart are required (i.e. With warm start command).