20.5. IOBOX diagnostics, statistics and logs

20.5. IOBOX diagnostics, statistics and logs
	Chapter 20. IOBOX

20.5.1. GPIO diagnostics and statistics

20.5.1.1. GPIO diagnostics

This command reports the current situation of the device:

[13:42:55] ABILIS_CPX:d d gpio

RES:Gpio-1 --------------------------------------------------------------------
       STATE:UP             USB-STATE:CONNECTED      
       - Digital Input Lines State --------------------------------------------
        1..16| off off off off off off off off .   .   .   .   .   .   .   .   
       ------------------------------------------------------------------------
       - Digital Output Lines State -------------------------------------------
        1..16| off off off off .   .   .   .   .   .   .   .   .   .   .   .   
       ------------------------------------------------------------------------
       - Analog Input Lines ---------------------------------------------------
             | State  Value   Unit     ADC    | State  Value   Unit     ADC
       ------+--------------------------------+--------------------------------
        1.. 2| NORMAL     10  C        0      | NORMAL    0.0  %        0      
        3.. 4| .           .  .        .      | .           .  .        .      
        5.. 6| .           .  .        .      | .           .  .        .      
        7.. 8| .           .  .        .      | .           .  .        .      
       ------------------------------------------------------------------------

The meaning:

STATE

GPIO driver state:

DOWN - device stopped or disconnected.
UP - device running.
INACTIVE - device good, but inactive (configuration parameter ACT:NO).

USB-STATE

USB device connection state:

DISCONNECTED - device disconnected from USB port.
CONNECTED - device connected.

D-IN:1...8 / D-OUT:1...4

GPIO digital input/output line state:

OFF - logical 0 state.
ON - logical 1 state.
N/A (not available) - unknown state.

State

GPIO analog input line state:

LOW - under the low threshold.
NORMAL - between high and low threshold.
HIGH - between high and low threshold.
N/A (not available) - unknown state.

Value

GPIO analog input line value. N/A (not available) - unknown state.

Unit

Unit for analog input/output lines.

ADC

Converted value from ADC value on analog input/output lines.

20.5.1.2. GPIO statistics

This command can help to understand what is happening, in case of troubles:

[13:48:36] ABILIS_CPX:d s gpio 

RES:Gpio-1 --------------------------------------------------------------------
       --- Cleared 13 days 21:06:37 ago, on 11/08/2017 at 18:08:13 ------------
       -----------|---INPUT---|--OUTPUT---|-----------|---INPUT---|--OUTPUT---|
       USB-CONN   |         67|           |USB-DISC   |           |         66|
       USB-AUTRST |          0|           |           |           |           |
       CHR        |   17650515|   13290463|FRM        |    2777250|    2777271|
       ------------------------------------------------------------------------

With reference to the shown interval of time («Cleared 13 days 21:06:37 ago») these counters show the number of:

`USB-CONN`	USB connections.
`USB-DISC`	USB disconnections.
`USB-AUTRST`	USB autorestarts. Troubles on USB interface.
`CHR`	Bytes in received/transmitted frames.
`FRM`	Received/transmitted frames.

20.5.2. MFIO diagnostics and statistics

20.5.2.1. MFIO diagnostics

This command reports the current situation of the device:

[13:42:55] ABILIS_CPX:d d mfio

RES:MfIo ----------------------------------------------------------------------
       Abilis_Multi_Function_IO_Interface                                      
       STATE:ACTIVE
       - Digital Input Lines State --------------------------------------------
        1..7| off off off off off off off 
       ------------------------------------------------------------------------
       - Digital Output Lines State -------------------------------------------
        1..7| off off off off off off off 
       ------------------------------------------------------------------------

The meaning:

STATE

MFIO driver state:

ACTIVE - device running.
INACTIVE - device good, but inactive (configuration parameter ACT:NO).

D-IN:1...7 / D-OUT:1...7

MFIO digital input/output line state:

OFF - logical 0 state.
ON - logical 1 state.
N/A (not available) - unknown state.

20.5.2.2. MFIO statistics

This command can help to understand what is happening, in case of troubles:

[13:48:36] ABILIS_CPX:d s mfio 

RES:MfIo ----------------------------------------------------------------------
       Abilis_Multi_Function_IO_Interface                                      
       --- Cleared 0 days 13:21:08 ago, on 25/08/2017 at 02:02:40 -------------
       -----------|---INPUT---|--OUTPUT---|-----------|---INPUT---|--OUTPUT---|
       IRQ        |         35|           |           |           |           |
       STATE      |          2|           |ERR-STATE  |          0|           |
       LINE-STATE |         63|           |ERR-LINE-ST|          0|           |
       ALARM      |         63|           |ERR-ALARM  |          0|           |
       ------------------------------------------------------------------------

With reference to the shown interval of time («Cleared 0 days 13:21:08 ago») these counters show the number of:

`IRQ`	MFIO interrupts.
`STATE`	Set State requests.
`LINE-STATE`	Set Line State requests.
`ALARM`	Set Alarm requests.
`ERR-STATE`	Errors during Set State.
`ERR-LINE-ST`	Errors during Set Line State.
`ERR-ALARM`	Errors during Set Alarm.

	Note
	If you notice incrementation of `ERR-STATE`, `ERR-LINE-ST` and `ERR-ALARM` consult Abilis support (tem@antek.it).

20.5.3. RVS diagnostics and statistics

20.5.3.1. RVS diagnostics

This command reports the current situation of the device:

[13:42:55] ABILIS_CPX:d d rvs

RES:Rvs-1 ---------------------------------------------------------------------
       STATE:UP                   MAC:B8-27-EB-93-FA-DF
       RemAdd-RemPort:192.168.029.101-41414
       CURRENT-IMAGE:5.000        FACTORY-IMAGE:5.000     BOARD:0.0
       - Digital Input Lines State --------------------------------------------
        1.. 4| ON  ON  ON  ON  
       ------------------------------------------------------------------------
       - Digital Output Lines State -------------------------------------------
        1.. 4| off ON  off off 
       ------------------------------------------------------------------------
       - Cameras diagnostics --------------------------------------------------
       CAM:  State:    LIVE: LIVE-REC: ALARM-REC: STORED-ALARMS: STORED-LIVE:
       ------------------------------------------------------------------------
       Cam-1 UP        0     NO        NO         54             0
       ------------------------------------------------------------------------

The meaning:

STATE

RVS driver state:

DOWN - device is down.
UP - device is active and ready.
INACTIVE - device is inactive.

MAC

RVS device driver MAC address.

RemAdd-RemPort

Remote IP address and remote port.

CURRENT-IMAGE

Current image version.

FACTORY-IMAGE

Factory image version.

D-IN:1...4 / D-OUT:1...4

RVS digital input/output line state:

OFF - logical 0 state.
ON - logical 1 state.
. (not available) - unknown state.

20.5.3.2. RVS statistics

This command can help to understand what is happening, in case of troubles:

[13:48:36] ABILIS_CPX:d s rvs 

RES:Rvs-1 ---------------------------------------------------------------------
       --- Cleared 0 days 14:12:29 ago, on 25/08/2017 at 02:02:39 -------------
       -----------|---INPUT---|--OUTPUT---|-----------|---INPUT---|--OUTPUT---|
       CONN-SUCC  |           |          1|BOARD-ERR  |          0|           |
       CONN-FAIL  |           |          0|           |           |           |
       CLOSE      |          0|          0|           |           |           |
       CFG-FAIL   |          0|           |SET-AO-CUT |          0|           |
       SET-FAIL   |           |          0|           |           |           |
       PROT-ERR   |          0|          0|           |           |           |
       IMAGE-ERR  |          0|           |           |
       ------------------------------------------------------------------------

With reference to the shown interval of time («Cleared 0 days 14:12:29») these counters show the number of:

`CONN-SUCC`	Successful opened sessions, at least a response received.
`CONN-FAIL`	Aborted sessions (on opening), TCP failed or no response received.
`CFG-FAIL`	Failed configuration of digital/analog parameters.
`SET-FAIL`	Failed setting of digital/analog outputs.
`PROT-ERR`	JMUX Errors.
`BOARD-ERR`	Connections aborted on Missing board.
`SET-AO-CUT`	Setting of analog outputs that where cutted.

	Note
	If you notice incrementation of these counters consult Abilis support (tem@antek.it).

20.5.4. RIO diagnostics and statistics

20.5.4.1. RIO diagnostics

This command reports the current situation of the device:

[13:42:55] ABILIS_CPX:d d rio

RES:Rio-1 ---------------------------------------------------------------------
       RIO                                                                     
       STATE:UP                   MAC:B8-27-EB-12-F7-FB
       RemAdd-RemPort:192.168.001.222-41414
       CURRENT-IMAGE:5.001        FACTORY-IMAGE:5.001     BOARD:1.6
       - Digital Input Lines State --------------------------------------------
        1.. 8| ON  ON  ON  ON  ON  ON  ON  ON  
       ------------------------------------------------------------------------
       - Digital Output Lines State -------------------------------------------
        1.. 8| off off off off off off off off 
       ------------------------------------------------------------------------
       - Analog Input Lines ---------------------------------------------------
             | State  Value   Unit     ADC    | State  Value   Unit     ADC
       ------+--------------------------------+--------------------------------
        1.. 2| NORMAL   50.0  %        2048   | NORMAL   50.0  %        2048   
        3.. 4| NORMAL   50.0  %        2048   | NORMAL   50.0  %        2048   
       ------------------------------------------------------------------------
       - Analog Output Lines --------------------------------------------------
             | State  Value   Unit     ADC    | State  Value   Unit     ADC
       ------+--------------------------------+--------------------------------
        1.. 2| NORMAL    0.0  %        0      | NORMAL    0.0  %        0      
        3.. 4| NORMAL    0.0  %        0      | NORMAL    0.0  %        0      
       ------------------------------------------------------------------------

The meaning:

STATE

RIO driver state:

DOWN - device is down.
UP - device is active and ready.
INACTIVE - device is inactive.

MAC

RIO device driver MAC address.

RemAdd-RemPort

Remote IP address and remote port.

CURRENT-IMAGE

Current image version.

FACTORY-IMAGE

Factory image version.

D-IN:1...8 / D-OUT:1...8

RIO digital input/output line state:

OFF - logical 0 state.
ON - logical 1 state.
. (not available) - unknown state.

State

RIO analog input/output line state:

LOW - under the low threshold.
NORMAL - between high and low threshold.
HIGH - between high and low threshold.
. (not available) - unknown state.

Value

RIO analog input line value. N/A (not available) - unknown state.

Unit

Unit for analog input/output lines.

ADC

Converted value from ADC value on analog input/output lines.

20.5.4.2. RIO statistics

This command can help to understand what is happening, in case of troubles:

[13:48:36] ABILIS_CPX:d s rio 

RES:Rio-1 ---------------------------------------------------------------------
       RIO                                                                     
       --- Cleared 17 days 01:07:47 ago, on 08/08/2017 at 15:19:38 ------------
       -----------|---INPUT---|--OUTPUT---|-----------|---INPUT---|--OUTPUT---|
       CONN-SUCC  |           |          1|BOARD-ERR  |          0|           |
       CONN-FAIL  |           |          0|           |           |           |
       CLOSE      |          0|          0|           |           |           |
       CFG-FAIL   |          0|           |SET-AO-CUT |          0|           |
       SET-FAIL   |           |          0|           |           |           |
       PROT-ERR   |          0|          0|           |           |           |
       ------------------------------------------------------------------------

With reference to the shown interval of time («Cleared 17 days 01:07:47 ago») these counters show the number of:

`CONN-SUCC`	Successful opened sessions, at least a response received.
`CONN-FAIL`	Aborted sessions (on opening), TCP failed or no response received.
`CFG-FAIL`	Failed configuration of digital/analog parameters.
`SET-FAIL`	Failed setting of digital/analog outputs.
`PROT-ERR`	JMUX Errors.
`BOARD-ERR`	Connections aborted on Missing board.
`SET-AO-CUT`	Setting of analog outputs that where cutted.

	Note
	If you notice incrementation of these counters consult Abilis support (tem@antek.it).

20.5.5. RVS/RIO logs

Available commands for logs:

[16:32:09] ABILIS_CPX:d rio-1 ?    

APPLOG         Rio APP log
IOLOG          Rio IO log
LOG            Rio log
SYSLOG         Rio SYS log

[16:39:23] ABILIS_CPX:d rvs-1 ?

APPLOG         Rvs APP log
IOLOG          Rvs IO log
LOG            Rvs log
SYSLOG         Rvs SYS log
VSLOG          Rvs VS log

These commands report the log of the device:

[16:40:56] ABILIS_CPX:d rvs-1 log

CURRENT EVENTS LOG MASK: DFT (ERR+INFO)


Current Local Time: Thursday 29/08/2019 16:41:02 (UTC+03:00)

Date   Time   Event Event detail
------ ------ ----- ------------------------------------------------------
290819 010949 Info  Full initialization
290819 010949 Info  CAMERA ID: 1
290819 010949 Info  CAMERA STATE: DOWN
290819 010949 Info  Enabling device
290819 010949 Info  STORAGE INITIALIZATION STARTED FOR CAMERA:1
290819 010950 Info  STORAGE INITIALIZATION COMPLETE CAMERA:1
290819 010950 Info  STORAGE INITIALIZATION NEW UUID created
290819 011002 Info  ALARM START
290819 011002 Info  IMAGE STREAM: DEVICE OR CAMERA DISABLED
290819 011007 Info  ALARM RENEWAL
290819 011007 Info  Trying to connect to device
290819 011007 Info  Device is connected
290819 011007 Info  Got response to Get Version
290819 011007 Info  Factory Version is: 5.000
290819 011007 Info  Current Version is: 5.3
290819 011007 Info  Hardware description is: Raspberry Pi 3 Model B Rev 1.2
290819 011007 Info  Hardware ID is: r3-1.2
290819 011010 Info  Got response to Get Board Type
290819 011010 Info  Board Type is: 0.0
290819 011010 Info  Successful setting: dout_1
290819 011010 Info  Successful setting: dout_2
290819 011010 Info  Successful setting: dout_3
290819 011010 Info  Successful setting: dout_4
290819 011010 Info  Notify State received
290819 011010 Info  CAMERA ID: 1
290819 011010 Info  CAMERA STATE: UP
290819 011010 Info  Getting supported parameters of camera: 1
290819 011010 Info  Setting parameter of camera: 1
290819 011011 Info  IMAGE STREAM: Trying to connect to the device
290819 011011 Info  IMAGE STREAM: Connected
290819 011108 Info  ALARM STOP
290819 011108 Info  Successful setting: dout_4
290819 020516 Info  ALARM START
290819 020516 Info  Successful setting: dout_4
290819 020617 Info  ALARM STOP
290819 020617 Info  Successful setting: dout_4

[15:32:36] ABILIS_CPX:d rio-1 log

CURRENT EVENTS LOG MASK: DFT (ERR+INFO)


Current Local Time: Thursday 29/08/2019 15:32:41 (UTC+02:00)

Date   Time   Event Event detail
------ ------ ----- ------------------------------------------------------
250819 005335 Info  Full initialization
250819 005335 Info  Enabling device
250819 005335 Info  Trying to connect to device
250819 005338 Info  Device is connected
250819 005338 Info  Got response to Get Version
250819 005338 Info  Factory Version is: 5.001
250819 005338 Info  Current Version is: 5.001
250819 005338 Info  Hardware description is: Raspberry Pi Model B Plus Rev 1.2
250819 005338 Info  Hardware ID is: r1-1.2
250819 005347 Info  Got response to Get Board Type
250819 005347 Info  Board Type is: 1.6
250819 005347 Info  Successful conf: ain_2_max
250819 005347 Info  Successful conf: ain_3_alarm_hi
250819 005347 Info  Successful conf: ain_3_alarm_lo
250819 005347 Info  Successful conf: ain_3_min
250819 005347 Info  Successful conf: ain_4_alarm_lo
250819 005347 Info  Successful conf: ain_2_alarm_lo
250819 005347 Info  Successful conf: ain_2_upd
250819 005347 Info  Successful conf: ain_2_alarm_hi
250819 005347 Info  Successful conf: ain_4_min
250819 005347 Info  Successful conf: ain_1_alarm_hi
250819 005347 Info  Successful conf: ain_1_poll
250819 005347 Info  Successful conf: adc_resolution
250819 005347 Info  Successful conf: adc_gain
250819 005347 Info  Successful conf: ain_1_upd
250819 005347 Info  Successful conf: ain_2_min
250819 005347 Info  Successful conf: ain_3_hyst
250819 005347 Info  Successful conf: ain_2_hyst
250819 005347 Info  Successful conf: ain_1_hyst
250819 005347 Info  Successful conf: ain_1_max
250819 005347 Info  Successful conf: ain_2_poll
250819 005347 Info  Successful conf: ain_1_alarm_lo
250819 005347 Info  Successful conf: ain_1_min
250819 005347 Info  Successful conf: ain_4_max
250819 005347 Info  Successful conf: ain_4_upd
250819 005347 Info  Successful conf: ain_3_upd
250819 005347 Info  Successful conf: ain_3_max
250819 005347 Info  Successful conf: ain_4_hyst
250819 005347 Info  Successful conf: ain_3_poll
250819 005347 Info  Successful conf: ain_4_alarm_hi
250819 005347 Info  Successful conf: ain_4_poll
250819 005347 Info  Successful conf: aout_2_alarm_hi
250819 005347 Info  Successful conf: aout_4_poll
250819 005347 Info  Successful conf: aout_1_poll
250819 005347 Info  Successful conf: aout_2_poll
250819 005347 Info  Successful conf: aout_1_upd
250819 005347 Info  Successful conf: aout_4_max
250819 005347 Info  Successful conf: aout_3_max
250819 005347 Info  Successful conf: aout_4_upd
250819 005347 Info  Successful conf: aout_3_alarm_lo
250819 005347 Info  Successful conf: aout_3_min
250819 005347 Info  Successful conf: aout_3_poll
250819 005347 Info  Successful conf: aout_1_alarm_hi
250819 005347 Info  Successful conf: aout_2_cut_lo
250819 005347 Info  Successful conf: aout_1_alarm_lo
250819 005347 Info  Successful conf: aout_1_max
250819 005347 Info  Successful conf: aout_2_min
250819 005347 Info  Successful conf: aout_4_min
250819 005347 Info  Successful conf: aout_3_cut_hi
250819 005347 Info  Successful conf: aout_4_alarm_hi
250819 005347 Info  Successful conf: aout_1_cut_hi
250819 005347 Info  Successful conf: aout_2_upd
250819 005347 Info  Successful conf: aout_3_upd
250819 005347 Info  Successful conf: aout_2_cut_hi
250819 005347 Info  Successful conf: aout_4_cut_lo
250819 005347 Info  Successful conf: aout_3_hyst
250819 005347 Info  Successful conf: aout_2_alarm_lo
250819 005347 Info  Successful conf: aout_3_alarm_hi
250819 005347 Info  Successful conf: aout_4_hyst
250819 005347 Info  Successful conf: aout_2_max
250819 005347 Info  Successful conf: aout_4_cut_hi
250819 005347 Info  Successful conf: aout_2_hyst
250819 005347 Info  Successful conf: aout_3_cut_lo
250819 005347 Info  Successful conf: aout_1_cut_lo
250819 005347 Info  Successful conf: aout_4_alarm_lo
250819 005347 Info  Successful conf: aout_1_min
250819 005347 Info  Successful conf: aout_1_hyst

To see the lO log type the following command:

[15:33:14] ABILIS_CPX:d rio-1 iolog 

2019-08-28 07:06:39,559Z - INFO jmux_commands_handler.py._set_dout:121/MainThread--1225740288: set digital output 1 to pulse (t=0.5, gap=0.5
), success: True
2019-08-28 07:06:39,630Z - INFO dio_monitoring_thread.py.run:45/D-IOMonitorThread--1283460000: digital io dout_1 has changed, new value: 1
2019-08-28 07:06:40,128Z - INFO dio_monitoring_thread.py.run:45/D-IOMonitorThread--1283460000: digital io dout_1 has changed, new value: 0
2019-08-28 10:04:01,707Z - INFO jmux_commands_handler.py._set_dout:121/MainThread--1225740288: set digital output 4 to pulse (t=0.5, gap=0.5
), success: True
2019-08-28 10:04:01,779Z - INFO dio_monitoring_thread.py.run:45/D-IOMonitorThread--1283460000: digital io dout_4 has changed, new value: 1
2019-08-28 10:04:02,221Z - INFO pulse.py._phase_thread_routine:146/PulseThread--1308625824: IMPULSE phase was interrupted
2019-08-28 10:04:02,293Z - INFO dio_monitoring_thread.py.run:45/D-IOMonitorThread--1283460000: digital io dout_4 has changed, new value: 0
2019-08-28 10:05:55,199Z - INFO jmux_commands_handler.py._set_dout:121/MainThread--1225740288: set digital output 4 to pulse (t=0.5, gap=0.5
), success: True

To see the VS log type the following command:

[16:48:02] ABILIS_CPX:d rvs-1 vslog

2019-08-29 13:30:35,773Z - INF jvs/msg_incoming-542 message 'keepalive' received, id=020100000944
2019-08-29 13:30:35,774Z - INF jvs/msg_outgoing-543 message 'ack' sent, id=020100000944
2019-08-29 13:30:35,775Z - INF jvs/msg_outgoing-543 message outgoing thread awaken
2019-08-29 13:30:41,062Z - INF jvs/msg_incoming-542 message 'log' received, id=020100000945
2019-08-29 13:30:41,066Z - INF jvs/msg_outgoing-543 message 'log_fragmet' sent, id=020100000945
2019-08-29 13:30:41,066Z - INF jvs/msg_outgoing-543 message outgoing thread awaken
2019-08-29 13:31:41,058Z - INF jvs/msg_incoming-542 message 'keepalive' received, id=020100000946
2019-08-29 13:31:41,059Z - INF jvs/msg_outgoing-543 message 'ack' sent, id=020100000946
2019-08-29 13:31:41,059Z - INF jvs/msg_outgoing-543 message outgoing thread awaken
2019-08-29 13:32:41,054Z - INF jvs/msg_incoming-542 message 'keepalive' received, id=020100000947
2019-08-29 13:32:41,054Z - INF jvs/msg_outgoing-543 message 'ack' sent, id=020100000947
2019-08-29 13:32:41,054Z - INF jvs/msg_outgoing-543 message outgoing thread awaken
2019-08-29 13:33:41,049Z - INF jvs/msg_incoming-542 message 'keepalive' received, id=020100000948
2019-08-29 13:33:41,049Z - INF jvs/msg_outgoing-543 message 'ack' sent, id=020100000948
2019-08-29 13:33:41,049Z - INF jvs/msg_outgoing-543 message outgoing thread awaken
2019-08-29 13:34:41,048Z - INF jvs/msg_incoming-542 message 'keepalive' received, id=020100000949
2019-08-29 13:34:41,049Z - INF jvs/msg_outgoing-543 message 'ack' sent, id=020100000949
2019-08-29 13:34:41,049Z - INF jvs/msg_outgoing-543 message outgoing thread awaken
2019-08-29 13:35:41,041Z - INF jvs/msg_incoming-542 message 'keepalive' received, id=020100000950
2019-08-29 13:35:41,041Z - INF jvs/msg_outgoing-543 message 'ack' sent, id=020100000950
2019-08-29 13:35:41,041Z - INF jvs/msg_outgoing-543 message outgoing thread awaken
2019-08-29 13:36:41,036Z - INF jvs/msg_incoming-542 message 'keepalive' received, id=020100000951
2019-08-29 13:36:41,037Z - INF jvs/msg_outgoing-543 message 'ack' sent, id=020100000951
2019-08-29 13:36:41,037Z - INF jvs/msg_outgoing-543 message outgoing thread awaken
2019-08-29 13:37:41,033Z - INF jvs/msg_incoming-542 message 'keepalive' received, id=020100000952
2019-08-29 13:37:41,033Z - INF jvs/msg_outgoing-543 message 'ack' sent, id=020100000952
2019-08-29 13:37:41,033Z - INF jvs/msg_outgoing-543 message outgoing thread awaken
2019-08-29 13:38:41,027Z - INF jvs/msg_incoming-542 message 'keepalive' received, id=020100000953
2019-08-29 13:38:41,028Z - INF jvs/msg_outgoing-543 message 'ack' sent, id=020100000953
2019-08-29 13:38:41,028Z - INF jvs/msg_outgoing-543 message outgoing thread awaken
2019-08-29 13:39:04,162Z - INF rcc/capture-552 frame is dark: 84/100
2019-08-29 13:39:04,163Z - INF msg/capture-552 sensors data changed
2019-08-29 13:39:04,163Z - INF jvs/msg_outgoing-543 message 'notify_sensors' sent, id=03928
2019-08-29 13:39:04,163Z - INF jvs/msg_outgoing-543 message outgoing thread awaken
2019-08-29 13:39:04,171Z - INF jvs/msg_incoming-542 message 'ack' received, id=03928
2019-08-29 13:39:04,171Z - INF msg/msg_incoming-542 received response for 'notify_sensors' command
2019-08-29 13:39:41,024Z - INF jvs/msg_incoming-542 message 'keepalive' received, id=020100000954
2019-08-29 13:39:41,024Z - INF jvs/msg_outgoing-543 message 'ack' sent, id=020100000954
2019-08-29 13:39:41,024Z - INF jvs/msg_outgoing-543 message outgoing thread awaken
2019-08-29 13:40:41,022Z - INF jvs/msg_incoming-542 message 'keepalive' received, id=020100000955
2019-08-29 13:40:41,022Z - INF jvs/msg_outgoing-543 message 'ack' sent, id=020100000955
2019-08-29 13:40:41,022Z - INF jvs/msg_outgoing-543 message outgoing thread awaken


20.4. RIO Sonoff WiFi Configuration		20.6. Activation of the alarms for IOBOX devices