51.1. PoEAC resource

51.1. PoEAC resource
	Chapter 51. POEAC - PPP Over Ethernet Access Concentrator

51.1.1. Activating the POEAC resource

Add the resource to the Abilis system with the following command, where n is resource identifier (in the range [1...999]).

[12:25:41] ABILIS_CPX:a res:poeac-1

COMMAND EXECUTED

	Caution
	After adding the POEAC active, you must restart the Abilis to make the resource running (use the command warm start to reboot the Abilis).

[17:14:59] ABILIS_CPX:s p poeac-1 act:yes

COMMAND EXECUTED

[12:59:38] ABILIS_CPX:d p poeac

RES:PoeAc-1 - Not Running, Not Saved (SAVE CONF) ------------------------------
       ------------------------------------------------------------------------
       DESCR:
       LOG:DS             ACT:YES                max-ipres:10   ipres-rxbuf:2  
       ETHRES:Eth-3                              
       ACNAME:wlan                               
       EMPTY-EQ-ANY:NO    ALL-SERVICES-OFFER:NO   
       ETH-JUMBO-FRAMES:NO
       - VLAN -----------------------------------------------------------------
       VLAN-ID:UNTAG

51.1.2. POEAC resource parameters

Use the following command to display the parameters of the resource; the d p poeac ? command shows the meaning of parameters.

[17:25:33] ABILIS_CPX:d p poeac

RES:PoeAc-1 -------------------------------------------------------------------
Run    DESCR:
       LOG:DS             ACT:YES                max-ipres:10   ipres-rxbuf:2  
       ETHRES:Eth-3                              
       ACNAME:wlan                               
       EMPTY-EQ-ANY:NO    ALL-SERVICES-OFFER:NO   
       ETH-JUMBO-FRAMES:NO
       - VLAN -----------------------------------------------------------------
       VLAN-ID:UNTAG

Meaning of the most important parametrs:

LOG: Logging functionalities activation/deactivation.
ACT: Operation activation [NO, YES].
ETHRES: Lower Ethernet resource [NONE, Eth-XXX, EthUsb-XXX, VEth]
max-ipres: Maximum number of concurrent ipres sessions [0..250]. There can't be more than this amount of external sessions connecting at once.
ipres-rxbuf: Number of receive buffers for each ipres session [1..255].
ACNAME: Access Concentrator name; the name of the Access Concentrator is sent along with responses to hosts. This parameter can be left blank in case there is only one AC in the network for each service-name requested.
EMPTY-EQ-ANY: Select whether the EMPTY service specified in PADI and PADR has to be considered a univocal service (more secure) or ANY service [NO, YES].
ALL-SERVICES-OFFER: Select whether PADO will contain only the requested service (more secure) or the list of all other available services too (less secure) [NO, YES].
ETH-JUMBO-FRAMES: Enable/disable ethernet jumbo frames (payload >1500 bytes) [NO, YES].
VLAN-ID: VLAN Identifier [0, 1..4094, UNTAG] <Only for ETHRES:Eth/EthUsb>.
PRIO-PPPOED: PPPOED priority over VLAN [0..7] <Only for VLAN-ID <> UNTAG>.
PRIO-LCP-IPCP: LCP and IPCP priority over VLAN [0..7] <Only for VLAN-ID <> UNTAG>.
PRIO-IP-LOW: VLAN priority for LOW IPCOS [0..7] <Only for VLAN-ID <> UNTAG>.
PRIO-IP-NORMAL: VLAN priority for NORMAL IPCOS [0..7] <Only for VLAN-ID <> UNTAG>.
PRIO-IP-HIGH: VLAN priority for HIGH IPCOS [0..7] <Only for VLAN-ID <> UNTAG>.

The following command allows the administrator to change the configuration of the resource:

s p poeac-n parameter:value...

	Caution
	To activate the changes made on the upper case parameters, execute the initialization command init res:poeac; while to set act the changes made on the lowercase parameters a save conf and an Abilis restart are required (i.e. With warm start command).


Chapter 51. POEAC - PPP Over Ethernet Access Concentrator		51.2. PPP Users table