Use the following command to add the device.

[09:33:26] ABILIS_CPX:a dev:rjs-1

COMMAND EXECUTED

[09:33:28] ABILIS_CPX:d dev

- Not Saved (SAVE CONF) -------------------------------------------------------

------------------ Active PCI Cards and Physical Resources: -------------------
Card(s)     Run Physical Resource(s) or CTI Port(s)          SlotId  Addr  Irq
-------------------------------------------------------------------------------
ASY-1       Yes Async-1  . . . . . . . . . . . . . . . . . .      -   3F8    4
ETH-1       Yes Eth-1  . . . . . . . . . . . . . . . . . . .      9   PCI (  5)
ETH-2       Yes Eth-2  . . . . . . . . . . . . . . . . . . .      8   PCI ( 10)
ETH-3       Yes Eth-3  . . . . . . . . . . . . . . . . . . .     10   PCI ( 12)
BRI4-1      Yes 31..34 . . . . . . . . . . . . . . . . . . .     12   PCI ( 10)
POTS-1      Yes 101..116 . . . . . . . . . . . . . . . . . .     11   PCI (  9)
CELL32-1    Yes 501..532 . . . . . . . . . . . . . . . . . .      -   PCI (  -)

------------------ Active USB Devices and Physical Resources: -----------------
Device(s)   Run Con Physical Resource(s) or CTI Port(s)    USBPORTID
-------------------------------------------------------------------------------
DSLUSB-1    Yes No  Dsl-1  . . . . . . . . . . . . . . . . NONE
CELLBOX-1           501..502 . . . . . . . . . . . . . . .
 CELL-1     Yes No  .  . . . . . . . . . . . . . . . . . . NONE
 CELL-2     Yes No  .  . . . . . . . . . . . . . . . . . . NONE
 CODEC-1    Yes No  .  . . . . . . . . . . . . . . . . . . NONE
 CONTROL-1  Yes No  .  . . . . . . . . . . . . . . . . . . NONE
RJS-1       No  No  Rjs-1  . . . . . . . . . . . . . . . . NONE


----------------- Inactive PCI Cards and Physical Resources: ------------------
Card(s)     Run Physical Resource(s) or CTI Port(s)          SlotId  Addr  Irq
-------------------------------------------------------------------------------
                     *** NO INACTIVE PCI CARDs PRESENT ***

----------------- Inactive USB Devices and Physical Resources: ----------------
Device(s)   Run Con Physical Resource(s) or CTI Port(s)    USBPORTID
-------------------------------------------------------------------------------
                    *** NO INACTIVE USB DEVICEs PRESENT ***

	Caution
	After adding or setting the device active, you must restart the Abilis to make the device running (use the command warm start to reboot the Abilis).

The following command is useful to enable the RJS device.

[09:37:23] ABILIS_CPX:s p rjs-1 act:yes

COMMAND EXECUTED

[09:37:51] ABILIS_CPX:init res:rjs-1

COMMAND EXECUTED

[09:37:55] ABILIS_CPX:d p rjs-1

RES:Rjs-1 ---------------------------------------------------------------------
Run    DESCR:
       LOG:NO           ACT:YES          LIVE-EXPIRY:120  REBOOT-PROTECTION:YES
       L1:AUTO    L1-DESCR:
       L2:AUTO    L2-DESCR:
       L3:AUTO    L3-DESCR:
       L4:AUTO    L4-DESCR:
       L5:AUTO    L5-DESCR:
       L6:AUTO    L6-DESCR:
       L7:AUTO    L7-DESCR:
       L8:AUTO    L8-DESCR:

	Caution
	The resource must be initialized using init res:rjs-1.

	Tip
	It's recommended to use a description for each line (Lx-DESCR parameters).

The most important parameters are:

[09:44:02] ABILIS_CPX:d p rjs-1 ?

Rjs resource parameter(s):

DESCR:     Resource description [Max. 80 aphanumeric extended characters]
LOG:       State changes log and alarm generation [NO, D, S, A, L, T, ALL] [+E]
           (D: Debug Log; S: System Log; A: Alarm view; L: Local audible alarm;
            T: SNMP traps; +E: Extended Log of state changes, see ref. manual)
ACT:       Operation activation [NO, YES]
LIVE-EXPIRY: Expiry timeout programmed to RJ45 switch [10..600 sec]
REBOOT-PROTECTION: Avoid transition to BACKUP during a reboot [NO, YES]
L1:        Define state of Line 1 at boot or upon INIT [AUTO, MAIN, BACKUP]
L1-DESCR:  Description for Line 1. Up to 70 alphanumeric extended characters.
           Spaces are not allowed, case is preserved.
L2:        Define state of Line 2 at boot or upon INIT [AUTO, MAIN, BACKUP]
L2-DESCR:  Description for Line 2. Up to 70 alphanumeric extended characters.
           Spaces are not allowed, case is preserved.
L3:        Define state of Line 3 at boot or upon INIT [AUTO, MAIN, BACKUP]
L3-DESCR:  Description for Line 3. Up to 70 alphanumeric extended characters.
           Spaces are not allowed, case is preserved.
L4:        Define state of Line 4 at boot or upon INIT [AUTO, MAIN, BACKUP]
L4-DESCR:  Description for Line 4. Up to 70 alphanumeric extended characters.
           Spaces are not allowed, case is preserved.
L5:        Define state of Line 5 at boot or upon INIT [AUTO, MAIN, BACKUP]
L5-DESCR:  Description for Line 5. Up to 70 alphanumeric extended characters.
           Spaces are not allowed, case is preserved.
L6:        Define state of Line 6 at boot or upon INIT [AUTO, MAIN, BACKUP]
L6-DESCR:  Description for Line 6. Up to 70 alphanumeric extended characters.
           Spaces are not allowed, case is preserved.
L7:        Define state of Line 7 at boot or upon INIT [AUTO, MAIN, BACKUP]
L7-DESCR:  Description for Line 7. Up to 70 alphanumeric extended characters.
           Spaces are not allowed, case is preserved.
L8:        Define state of Line 8 at boot or upon INIT [AUTO, MAIN, BACKUP]
L8-DESCR:  Description for Line 8. Up to 70 alphanumeric extended characters.
           Spaces are not allowed, case is preserved.

The most important parameters are:

When REBOOT-PROTECTION:YES and WARM START or RESTART SYSTEM is done, a special signal is sent to RJ45 switch that temporarily increase the LIVE-EXPIRY to 10 minutes. In this way the lines aren't switched during a normal system reboot.

	Note
	If the RJ45 switch is POWERED OFF all the lines are switched to BACKUP.

The lines can be configured independently via L1: to L8: parameters:

The state of the lines can be temporary forced using the S S RES:RJS-x Lx:AUTO | MAIN | BACKUP | DEFAULT command.