42.1. PoEAC resource

42.1. PoEAC resource
	Chapter 42. POEAC - PPP Over Ethernet Access Concentrator

42.1.1. Activating the POEAC resource

Add the resource to the Abilis system with the following command, where n is resource identifier (in the range [1...999]).

[12:25:41] ABILIS_CPX:a res:poeac-1

COMMAND EXECUTED

	Caution
	After adding the POEAC active, you must restart the Abilis to make the resource running (use the command warm start to reboot the Abilis).

[17:14:59] ABILIS_CPX:s p poeac-1 act:yes

COMMAND EXECUTED

[12:59:38] ABILIS_CPX:d p poeac

RES:PoeAc-1 - Not Running, Not Saved (SAVE CONF) ------------------------------
       ------------------------------------------------------------------------
       DESCR:
       LOG:DS             ACT:YES                max-ipres:10   ipres-rxbuf:2  
       ETHRES:Eth-3                              
       ACNAME:wlan                               
       EMPTY-EQ-ANY:NO    ALL-SERVICES-OFFER:NO   
       ETH-JUMBO-FRAMES:NO
       - VLAN -----------------------------------------------------------------
       VLAN-ID:UNTAG

42.1.2. POEAC resource parameters

Use the following command to display the parameters of the resource; the d p poeac ? command shows the meaning of parameters.

[17:25:33] ABILIS_CPX:d p poeac

RES:PoeAc-1 -------------------------------------------------------------------
Run    DESCR:
       LOG:DS             ACT:YES                max-ipres:10   ipres-rxbuf:2  
       ETHRES:Eth-3                              
       ACNAME:wlan                               
       EMPTY-EQ-ANY:NO    ALL-SERVICES-OFFER:NO   
       ETH-JUMBO-FRAMES:NO
       - VLAN -----------------------------------------------------------------
       VLAN-ID:UNTAG

Meaning of the most important parametrs:

LOG: Logging functionalities activation/deactivation.
ACT: Runtime POEAC activation/deactivation.
ETHRES: Lower Ethernet resource [NONE, Eth-XXX, EthUsb-XXX, VEth]
max-ipres: Sets the number of PPPoE sessions the module can support. There can't be more than this amount of external sessions connecting at once.
ipres-rxbuf: Sets the number of PPPoE packets received from client a module can hold while sending other packets to remote PPP.
ACNAME: Access Concentrator name; the name of the Access Concentrator is sent along with responses to hosts. This parameter can be left blank in case there is only one AC in the network for each service-name requested.
EMPTY-EQ-ANY: Select whether the EMPTY service specified in PADI and PADR has to be considered a univocal service (more secure) or ANY service.
ALL-SERVICES-OFFER: Select whether PADO will contain only the requested service (more secure) or the list of all other available services too (less secure).
ETH-JUMBO-FRAMES: Enable/disable ethernet jumbo frames (payload >1500 bytes) [NO, YES].
VLAN-ID: VLAN Identifier [0, 1..4094, UNTAG] <Only for ETHRES:Eth>.
PRIO-PPPOED: PPPOED priority over VLAN [0..7] <Only for VLAN-ID <> UNTAG>.
PRIO-LCP-IPCP: LCP and IPCP priority over VLAN [0..7] <Only for VLAN-ID <> UNTAG>.

The following command allows the administrator to change the configuration of the resource:

s p poeac-n parameter:value...

	Caution
	To activate the changes made on the upper case parameters, execute the initialization command init res:poeac; while to set act the changes made on the lowercase parameters a save conf and an Abilis restart are required (i.e. With warm start command).


Chapter 42. POEAC - PPP Over Ethernet Access Concentrator		42.2. PPP Users table