17.2. RJS device activation

Use the following command to add the device.

[09:33:26] ABILIS_CPX:a dev:rjs-1

COMMAND EXECUTED

[09:33:28] ABILIS_CPX:d dev

- Not Saved (SAVE CONF) -------------------------------------------------------

--------------- Active Watchdog and MFxx Resources (read only): ---------------
Device(s)   Run Physical Resource(s)                         SlotId  Addr  Irq
-------------------------------------------------------------------------------
MF          Yes Mf . . . . . . . . . . . . . . . . . . . . .      -  AC00   19
MFIO        No  MfIo . . . . . . . . . . . . . . . . . . . .      -  AC00   19

------------------ Active PCI Devices and Physical Resources: -----------------
Device(s)   Run Physical Resource(s) or CTI Port(s)          SlotId  Addr  Irq
-------------------------------------------------------------------------------
ASY-1       Yes Async-1  . . . . . . . . . . . . . . . . . .      -   3F8    4
ETH-1       Yes Eth-1  . . . . . . . . . . . . . . . . . . .      9   PCI (  5)
ETH-2       Yes Eth-2  . . . . . . . . . . . . . . . . . . .      8   PCI ( 10)
ETH-3       Yes Eth-3  . . . . . . . . . . . . . . . . . . .     10   PCI ( 12)
BRI4-1      Yes 31..34 . . . . . . . . . . . . . . . . . . .     12   PCI ( 10)
POTS-1      Yes 101..116 . . . . . . . . . . . . . . . . . .     11   PCI (  9)
CELL32-1    Yes 501..532 . . . . . . . . . . . . . . . . . .      -   PCI (  -)

------------------ Active USB Devices and Physical Resources: -----------------
Device(s)   Run Con Physical Resource(s) or CTI Port(s)    USBPORTID
-------------------------------------------------------------------------------
DSLUSB-1    Yes No  Dsl-1  . . . . . . . . . . . . . . . . NONE
CELLBOX-1           501..502 . . . . . . . . . . . . . . .
 CELL-1     Yes No  .  . . . . . . . . . . . . . . . . . . NONE
 CELL-2     Yes No  .  . . . . . . . . . . . . . . . . . . NONE
 CODEC-1    Yes No  .  . . . . . . . . . . . . . . . . . . NONE
 CONTROL-1  Yes No  .  . . . . . . . . . . . . . . . . . . NONE
RJS-1       No  No  Rjs-1  . . . . . . . . . . . . . . . . NONE


-------------- Inactive Watchdog and MFxx Resources (read only): --------------
Device(s)   Run Physical Resource(s)                         SlotId  Addr  Irq
-------------------------------------------------------------------------------
                     *** NO INACTIVE WATCHDOGs PRESENT ***                     

----------------- Inactive PCI Devices and Physical Resources: ----------------
Device(s)   Run Physical Resource(s) or CTI Port(s)          SlotId  Addr  Irq
-------------------------------------------------------------------------------
                     *** NO INACTIVE PCI CARDs PRESENT ***                     

----------------- Inactive USB Devices and Physical Resources: ----------------
Device(s)   Run Con Physical Resource(s) or CTI Port(s)    USBPORTID
-------------------------------------------------------------------------------
                    *** NO INACTIVE USB DEVICEs PRESENT ***  
[Caution]Caution

After adding or setting the device active, you must restart the Abilis to make the device running (use the command warm start to reboot the Abilis).

The following command is useful to enable the RJS device.

[09:37:23] ABILIS_CPX:s p rjs-1 act:yes

COMMAND EXECUTED

[09:37:51] ABILIS_CPX:init res:rjs-1

COMMAND EXECUTED

[09:37:55] ABILIS_CPX:d p rjs-1

RES:Rjs-1 ---------------------------------------------------------------------
Run    DESCR:
       LOG:NO           ACT:YES          LIVE-EXPIRY:120  REBOOT-PROTECTION:YES
       L1:AUTO    L1-DESCR:
       L2:AUTO    L2-DESCR:
       L3:AUTO    L3-DESCR:
       L4:AUTO    L4-DESCR:
       L5:AUTO    L5-DESCR:
       L6:AUTO    L6-DESCR:
       L7:AUTO    L7-DESCR:
       L8:AUTO    L8-DESCR:
[Caution]Caution

The resource must be initialized using init res:rjs-1.

[Tip]Tip

It's recommended to use a description for each line (Lx-DESCR parameters).

The most important parameters are:

[09:44:02] ABILIS_CPX:d p rjs-1 ?

Rjs resource parameter(s):

DESCR:     Resource description.
           Max 79 chars. Spaces require double quotes (E.g. "str1 str2").
LOG:       State changes log and alarm generation [NO, D, S, A, L, T, ALL] [+E]
           (D: Debug Log; S: System Log; A: Alarm view; L: Local audible alarm;
            T: SNMP traps; +E: Extended Log of state changes, see ref. manual)
ACT:       Operation activation [NO, YES]
LIVE-EXPIRY: Expiry timeout programmed to RJ45 switch [10..600 sec]
REBOOT-PROTECTION: Avoid transition to BACKUP during a reboot [NO, YES]
L1:        Define state of Line 1 at boot or upon INIT [AUTO, MAIN, BACKUP]
L1-DESCR:  Description for Line 1.
           Max 70 chars. Spaces require double quotes (E.g. "str1 str2").
L2:        Define state of Line 2 at boot or upon INIT [AUTO, MAIN, BACKUP]
L2-DESCR:  Description for Line 2.
           Max 70 chars. Spaces require double quotes (E.g. "str1 str2").
L3:        Define state of Line 3 at boot or upon INIT [AUTO, MAIN, BACKUP]
L3-DESCR:  Description for Line 3.
           Max 70 chars. Spaces require double quotes (E.g. "str1 str2").
L4:        Define state of Line 4 at boot or upon INIT [AUTO, MAIN, BACKUP]
L4-DESCR:  Description for Line 4.
           Max 70 chars. Spaces require double quotes (E.g. "str1 str2").
L5:        Define state of Line 5 at boot or upon INIT [AUTO, MAIN, BACKUP]
L5-DESCR:  Description for Line 5.
           Max 70 chars. Spaces require double quotes (E.g. "str1 str2").
L6:        Define state of Line 6 at boot or upon INIT [AUTO, MAIN, BACKUP]
L6-DESCR:  Description for Line 6.
           Max 70 chars. Spaces require double quotes (E.g. "str1 str2").
L7:        Define state of Line 7 at boot or upon INIT [AUTO, MAIN, BACKUP]
L7-DESCR:  Description for Line 7.
           Max 70 chars. Spaces require double quotes (E.g. "str1 str2").
L8:        Define state of Line 8 at boot or upon INIT [AUTO, MAIN, BACKUP]
L8-DESCR:  Description for Line 8.
           Max 70 chars. Spaces require double quotes (E.g. "str1 str2").

The most important parameters are:

LIVE-EXPIRY

Expiry timeout programmed to RJ45 switch [10..600 sec]. How much time the live signals from the Abilis CPX must be absent prior to switch to BACKUP. The default value of 120 seconds is intentionally large to avoid problematic flapping of the lines.

REBOOT-PROTECTION

Avoid transition to BACKUP during a reboot [NO, YES]. When you reboot the Abilis CPX, the live signal will disappear for the period needed to have the Abilis functional again. In some cases this may take longer that LIVE-EXPIRY.

When REBOOT-PROTECTION:YES and WARM START or RESTART SYSTEM is done, a special signal is sent to RJ45 switch that temporarily increase the LIVE-EXPIRY to 10 minutes. In this way the lines aren't switched during a normal system reboot.

[Note]Note

If the RJ45 switch is POWERED OFF all the lines are switched to BACKUP.

The lines can be configured independently via L1: to L8: parameters:

AUTO

This is the normal way. The line is switched to BACKUP when the RJ45 box is not driven (e.g. Abilis powered off), and switched to MAIN when the RJ45 box is driven.

MAIN

The Line is forced to MAIN as soon as the RJS is powered on, and will stay MAIN.

BACKUP

The Line is forced to BACKUP as soon as the RJS is powered on, and will stay BACKUP.

The state of the lines can be temporary forced using the S S RES:RJS-x Lx:AUTO | MAIN | BACKUP | DEFAULT command.