| 17.4. CTI GSM/UMTS/LTE ports diagnostics and statistics | ||
|---|---|---|
 | Chapter 17. UMTS BOX |  |
| 17.4. CTI GSM/UMTS/LTE ports diagnostics and statistics | ||
|---|---|---|
| | Chapter 17. UMTS BOX | |
This command reports the current situation of the device:
[09:21:45] ABILIS_CPX:d d ctip:502
CTIP:502 ----------------------------------------------------------------------
SIM_3204748405_(EX_RETENOI_3276270837)
USER:# OPSTATE:UP STATE:UP
------------------------------------------------------------------------
CH: STATE: [Q932-STATE:] CG: [SG:] CD: [SD:]
------------------------------------------------------------------------
*** All channels disconnected ***
------------------------------------------------------------------------
VOICE-STATE:READY PDN-STATE:READY SMS-STATE:READY
------------------------------------------------------------------------
NET:WIND NET-MODE:GSM ROAMING:NO
SIGNAL:22 SIGNAL-dbm:-69 RXQUAL:0
IMEI:357396012653490 IMSI:222881451579032 SIM:8939883345002210328
SMSC:+393205858500 CODEC-ISO-BW:1304000 SIM-SEL:FIX-SIM-A
CELL-MODEL:SIM5210 CELL-VER:V1.92 CELL-FEAT:VOICE,DATA,SMS
CELL:CONNECTED CELL-STATE:READY CELL-ERR:NONE
CODEC:CONNECTED CODEC-STATE:READY CODEC-ERR:NONE
CONTROL:CONNECTED CONTROL-STATE:READY CONTROL-ERR:NONEThe meaning:
USERName of the user assigned to this port. Max 32 ASCII characters or #. The user must be present and it must not be already assigned to another port.
OPSTATEThe overall state of the port.
VOICE-STATEThe overall state of the GSM VOICE connection:
DOWN - Not ready to place or receive
VOICE calls, either because of missing connection to the
network or for some administratively or configuration
reasons.
READY - Ready to place and receive
VOICE calls.
IN-USE - A VOICE connection is
ongoing or active.
PDN-STATEThe overall state of the PDN (Packet Data Network) connection:
DOWN - Not ready to attach to PDN,
either because of missing connection to the network or for
some administratively or configuration reasons.
READY - Ready to attach to
PDN.
IN-USE - A PDN connection is ongoing
or active.
BLOCKED - When the USB MODEM
interface is blocked (The state should not survive too long,
because safety timer restarts whole USB device after enter
this state and timeout).
SMS-STATEThe overall state of the SMS channel:
DOWN - Ready to send/receive
SMSs.
READY - Ready to send/receive
SMSs.
NETThe currently used GSM network name.
ROAMINGShows if the currently used UMTS/GSM network is ROAMING type:
N/A - The ROAMING diagnostic isn't
valid (when NO SIM card inserted, when no network registered
etc).
NO - The used network isn't ROAMING
type.
YES - The used network is ROAMING
type.
NET-MODEShows if the currently used network is GSM, UMTS or LTE.
SIGNALSignal quality (0 = -113 dBm or less, 1..30 = -111.. -53 dBm, 31 = -51 dBm, or greater 99 = not known or not detectable, 100 = N/A value when the device isn't connected)
RXQUALThe value of BER (bit error rate) of the existing call.
IMEIInternational Mobile Equipment Identity number.
IMSIInternational Mobile Subscriber Identity number.
SIMSIM card identification number.
SMSCSMS Center number.
CODEC-ISO-BWIndicates the bandwidth of the AUDIO-CODEC ISO interface.
CELL-MODELThe CELL device model currently used by the port:
N/A - No device connected.
SIM5210 - SimCom 5210 module
connected (UMTSBOX2 2011).
SIM5218 - SimCom 5218 module
connected (UMTSBOX2 2012).
UD7200 - UMTSKEY module
connected.
SIM7230E - SimCom 7230E module
connected.
SIM7250E - SimCom 7250E module
connected.
CELLShows if the hot-pluggable device is connected or not:
DISCONNECTED - Not connected to
CPX.
CONNECTED - Connected to CPX.
UNAVAIL - No Gsm module is available
for this GSM port (USB subsystem decides about the
availability).
CELL-STATEShows the state of the USB interface of the GSM USB module:
INIT - Wait for
initialisation.
READY - Completely initialised and
ready to use.
FAILED - Failed because of serious
troubles detected on the USB bus.
CELL-ERRShows the reason of the not READY GSM module:
NONE - No error detected, the GSM
module works fine.
N/A - Not applicable error, the error
is given by values in GsmUsb and GsmUsbState values whose are
three states and cannot be expressed by this two state
diagnostic. Usually when GSM device is disconnected or its
handle isn't available.
USB-NO-RESP - USB RTU_NO_RESPONSE
error was detected.
USB-OVERCUR - USB RTU_OVERCURRENT
error was detected.
USB-NO-BW - USB RTU_BANDWIDTH error
was detected.
NO-COM - AT interface doesn't work,
detected by the At interface watchdog.
NO-SIM - No SIM card is inserted into
the module.
SIM-LOCK - The CME-ERROR: 252 (SIM
BLOCKED) was detected during the checking of the PIN
protection state.
SIM-ERR - The CME-ERROR: different
from 252 was detected during the checking of the PIN
protection state.
PIN - Waits for PIN enter, the left
number of attempts 2 or 1. When the 3 attempts are available
the PIN from port configuration is automatically
entered.
PUK - Waits for PUK enter.
PIN2 - Waits for PIN2 enter.
PUK2 - Waits for PUK2 enter.
NO-SIG - No GSM signal is available.
The AT+CSQ command returns the value 99.
NO-NET - The GSM network isn't
available.
NO-REG - The GSM module isn't
registered into the network.
UNKNOWN - Unknown or not handled
error.
CODECShows if the hot-pluggable device is connected or not:
DISCONNECTED - The AUDIO module is
not connected to CPX.
CONNECTED - The AUDIO module is
connected to CPX.
UNAVAIL - No AUDIO module is
available for this GSM port (USB subsystem decides about the
availability).
INACTIVE - The AUDIO device isn't
available because of inactivating state set by S
INACT command.
CODEC-STATEShows the state of the USB interface of the CODEC module:
INIT - Wait for
initialisation.
READY - Completely initialised and
ready to use.
FAILED - Failed because of serious
troubles detected on the USB bus.
CODEC-ERRShows the reason of the not READY GSM codec:
NONE - No error detected, the GSM
codec works fine.
USB-OVERCUR - USB RTU_OVERCURRENT
error was detected.
USB-NO-BW - USB RTU_BANDWIDTH error
was detected.
N/A - Not applicable error, the error
is given by values in GsmUsb and GsmUsbState values whose are
three states and cannot be expressed by this two state
diagnostic.
CONTROLShows if the hot-pluggable device is connected or not.
CONTROL-STATEShows the state of the USB interface of the CONTROL (PIC) module.
CONTROL-ERRShows the reason of the not READY GSM CONTROL (PIC).
Diagnostics of a CTI GSM port when a call is running:
[09:23:17] ABILIS_CPX:d d ctip:502
CTIP:502 ----------------------------------------------------------------------
SIM_xxxxxxxxxx
USER:# OPSTATE:UP STATE:UP
------------------------------------------------------------------------
CH: STATE: [Q932-STATE:] CG: [SG:] CD: [SD:]
------------------------------------------------------------------------
1 07-LOC-ALERT 779 xxxxxxxxxx
------------------------------------------------------------------------
VOICE-STATE:IN-USE PDN-STATE:READY SMS-STATE:READY
------------------------------------------------------------------------
NET:WIND NET-MODE:GSM ROAMING:NO
SIGNAL:22 SIGNAL-dbm:-69 RXQUAL:0
IMEI:357396012653490 IMSI:222881451579032 SIM:8939883345002210328
SMSC:+393205858500 CODEC-ISO-BW:1304000 SIM-SEL:FIX-SIM-A
CELL-MODEL:SIM5210 CELL-VER:V1.92 CELL-FEAT:VOICE,DATA,SMS
CELL:CONNECTED CELL-STATE:READY CELL-ERR:NONE
CODEC:CONNECTED CODEC-STATE:READY CODEC-ERR:NONE
CONTROL:CONNECTED CONTROL-STATE:READY CONTROL-ERR:NONE![[Tip]](../images/tip.png) | Tip |
|---|---|
CODEC-ISO-BW shows the USB Isochronous bandwidth reserved on the USB controller to serve the CTIP. The audio codec always reserves the bandwidth of TWO CTIP even if one is disabled. |
This is what appears in the CTIR Connection (from PBX port group to GSM gateway):
[12:06:44] ABILIS_CPX:d ctic
SES ID Type Input Output PR State Cgi (Calling In) Cdo (Called Out)
---- ---- ---- -------- -------- --- ------ ------------------- --------------------
2 2 TR G1 502 3 ACTIVE 711 3482233445
Scanning available networks.
Example of NETSCAN:
[10:54:26] ABILIS_CPX:d d ctip:501 netscanTHE COMMAND WILL SEARCH ALL AVAILABLE NETWORKs. THIS OPERATION MAY TAKE FEW MINUTES. PROCEED ANYWAY (N/Y)?yCTIP:501 ---------------------------------------------------------------------- SIM_xxxxxxxxxx USER:# OPSTATE:UP STATE:UP ------------------------------------------------------------------------ CH: STATE: [Q932-STATE:] CG: [SG:] CD: [SD:] ------------------------------------------------------------------------ *** All channels disconnected *** ------------------------------------------------------------------------ VOICE-STATE:READY PDN-STATE:READY SMS-STATE:READY ------------------------------------------------------------------------ NET:WIND NET-MODE:GSM ROAMING:NO SIGNAL:22 SIGNAL-dbm:-69 RXQUAL:0 IMEI:357396012653300 IMSI:222881672196219 SIM:8939880367011211389 SMSC:+393205858500 CODEC-ISO-BW:1304000 SIM-SEL:FIX-SIM-A CELL-MODEL:SIM5210 CELL-VER:V1.92 CELL-FEAT:VOICE,DATA,SMS CELL:CONNECTED CELL-STATE:READY CELL-ERR:NONE CODEC:CONNECTED CODEC-STATE:READY CODEC-ERR:NONE CONTROL:CONNECTED CONTROL-STATE:READY CONTROL-ERR:NONE - Available Networks --------------------------------------------------- Status: Name: Code: Mode: CURRENT WIND 22288 GSM AVAILABLE WIND 22288 UMTS AVAILABLE 3ITA 22299 UMTS FORBIDDEN OMNITEL 22210 GSM FORBIDDEN OMNITEL 22210 UMTS FORBIDDEN TIM 22201 UMTS FORBIDDEN TIM 22201 GSM
![[Note]](../images/note.png) | Note |
|---|---|
If NETSCAN cannot be executed for any reason, e.g. because there is an active call or the module is disconnected, the message *** CANNOT EXECUTE NETSCAN *** is printed. |
This command can help to understand what is happening, in case of troubles:
Shows the statistics of all the CTI ports such as the number of calls (successful and unsuccessful), the duration of the calls, the number of connection/disconnection of the GSM/UMTS device, the number of connection/disconnection of the audio-codec device and the number of CELL packets exchanged.
Shows the statistics of a single CTI port.
[16:14:19] ABILIS_CPX:d s ctip:501
CTIP:501 ----------------------------------------------------------------------
SIM-3883634235
USER:#
--- Cleared 0 days 19:47:27 ago, on 14/05/2015 at 19:23:22 -------------
Layer 3 Q.931
-----------|---INPUT---|--OUTPUT---|-----------|---INPUT---|--OUTPUT---|
FAIL-CALL | 0| 0|SUCC-CALL | 2| 0|
TIME-CALL | 48| 0|
------------------------------------------------------------------------
Layer 2 PDN
-----------|---INPUT---|--OUTPUT---|-----------|---INPUT---|--OUTPUT---|
PDN-CALL | | 0|PDN-CHAR | 0| 0|
PDN-TIME | | 0|PDN-FRM | 0| 0|
PDN-TIME-15| | 0|PDN-LOST | 0| 0|
| | |PDN-LONG | 0| 0|
------------------------------------------------------------------------
Layer 2 SMS
-----------|---INPUT---|--OUTPUT---|-----------|---INPUT---|--OUTPUT---|
SMS | 0| 0|SMS-FAIL | 0| 0|
------------------------------------------------------------------------
Layer 1 CELL
-----------|---INPUT---|--OUTPUT---|-----------|---INPUT---|--OUTPUT---|
CELL-DISC | 0| | | | |
CELL-CONN | 1| | | | |
CELL-MRST | 0| | | | |
CELL-ARST | 0| | | | |
CELL-HWRST | 0| | | | |
CELL-PCK | 68796| 34389| | | |
CELL-OVR | 0| | | | |
------------------------------------------------------------------------
CODEC-DISC | 0| |CONTR-DISC | 0| |
CODEC-CONN | 1| |CONTR-CONN | 1| |
CODEC-MRST | 0| |CONTR-MRST | 0| |
CODEC-ARST | 0| |CONTR-ARST | 0| |
CODEC-HWRST| 0| | | | |
CODEC-PCK | 71240766| 71241074|CONTR-PCK | 71254| 71255|
CODEC-OVR | 0| |CONTR-PCKH | 0| 0|
CODEC-UND | | 0| | | |
------------------------------------------------------------------------With reference to the shown interval of time («Cleared 0 days 19:47:27 ago») these counters show the number of:
FAIL-CALL | Failed incoming/outgoing voice calls. |
TIME-CALL | The sum of all PDN calls. |
SUCC-CALL | The sum of established incoming/outgoing voice calls duration. |
PDN-CALL | Established PDN calls. |
PDN-TIME | The sum of all PDN calls duration. |
PDN-TIME-15 | PDN calls 15 minutes interval counter. |
PDN-CHAR | Chars (bytes) received/sent in the incoming/outgoing ASYND HDLC frames. |
PDN-FRM | Incoming/outgoing ASYNC HDLC frames into/from CELL port. |
PDN-LOST | IN - HDLC frames received but discarded. OUT - HDLC frames that was not sent within a timeout (1.5 secs), and discarded. |
PDN-LONG | IN - HDLC frames received discarded because too long. OUT - HDLC frames not sent because too long. |
SMS | Incoming/outgoing SMS messages. |
SMS-FAIL | Discarded incoming/outgoing SMS messages. |
CELL-DISC | Disconnection of the CELL device. |
CELL-CONN | Connection of the CELL device. |
CELL-MRST | Manual restarts performed on the CELL module. |
CELL-ARST | CELL module auto restarts because of serious troubles on USB interface. |
CELL-HWRST | CELL module restarts made by PIC command. |
CELL-PCK | USB data blocks received/transmitted from/to the CELL module. |
CELL-OVR | Detected overruns on Serial to USB interface. |
CODEC-DISC | Audio codec disconnections from USB. |
CODEC-CONN | Audio codec connections into USB. |
CODEC-MRST | Manual restarts performed on the CELL Audio module. |
CODEC-ARST | Auto-restarts performed on the CELL Audio module. |
CODEC-HWRST | CODEC device restarts made via the PIC device. |
CODEC-OVR | Detected overruns errors on USB Audio-Codec. |
CODEC-UND | Detected USB underrun errors on USB Audio-Codec. |
CONTR-DISC | PIC chip disconnections from USB. |
CONTR-CONN | PIC chip connections into USB.. |
CONTR-MRST | Manual restarts performed on the PIC module |
CONTR-ARST | Auto-restarts performed on the PIC module |
CONTR-PCK | USB packets sent/received into/from the PIC of the CELL device. |
CONTR-PCKH | High priority USB packets sent/received into/from the PIC of the CELL device. |
| |  | |
| 17.3. Last Calling Service for UMTSBOX |  | 17.5. How to update UMTSBOX-2 firmware |