20.3. IP Resources

20.3. IP Resources
	Chapter 20. IPRTR - IP Router

The IP Router of Abilis CPX can manage up to 256 IP resources. The IP configuration of each resource is stored into the routing table.

The available commands for managing the IP resources are the following:

d p ip
a res:ip
c res:ip
s p ip

20.3.1. D P IP (Display Parameter IP resource)

It shows the IP resources table. By omitting the IP resource identifier, the command will show all the resources currently defined.

[08:32:56] ABILIS_CPX:d p ip

RES:Ip-1 - IP over LAN (LAN) --------------------------------------------------
Run    DESCR:LAN
       OPSTATE:UP             LOG:NO                 STATE-DETECT:NORMAL
       LANRES:Eth-1
       IPADD:192.168.029.254  MASK:255.255.255.000   
       REDIS:EXT     HIDE:NO         RP:NONE            IPSEC:NO       VRRP:NO
       NAT:INSIDE    UPNP:NO         DIFFSERV:NO        DDNS:NO
       OUTBUF:100    OUTQUEUE:FAIR   MTU:1500           BRD:NET
       OUTSPL:NO     
       INBUF:0                       mru:1500           SRCV:NO
       - TRFA section ---------------------------------------------------------
       TRFA:YES     TRFA-MODE:TOTALS       
       - Lan ------------------------------------------------------------------
       LLOG:NO       arpcache:200    CACHETIMER:120     rxbuf:4     txbuf:14
       VLAN-ID:UNTAG 

RES:Ip-22 - IP over PPP (PPP) -------------------------------------------------
Run    DESCR:UMTS-DATA
       OPSTATE:UP             LOG:NO                 STATE-DETECT:NORMAL
       LOWRES:CtiSLink                               
       IPADD:RETRIEVE                                NEIGH:RETRIEVE
       REDIS:EXT     HIDE:NO         RP:NONE            IPSEC:NO       VRRP:NO
       NAT:INSIDE    UPNP:NO         DIFFSERV:NO        DDNS:NO
       OUTBUF:100    OUTQUEUE:FAIR   MTU:1500           
       OUTSPL:NO     
       INBUF:0                       mru:1500           SRCV:NO
       - TRFA section ---------------------------------------------------------
       TRFA:NO      
       - Ppp ------------------------------------------------------------------
       PPPLOG:DS        NRTY3:NOMAX     PPP-ENC:RAW-PPP           RADIUS:NO
       DT-IN:300        DT-OUT:300      UDT-IN:NOMAX              UDT-OUT:NOMAX
       - Dial-in --------------------------------------------------------------
       DIAL-IN:NO    
       CGI:*                        SGI:DISABLED                 
       CDI:*                        SDI:*                        
       - Dial-out -------------------------------------------------------------
       TI:ALL,00:00-23:59           BOOT-DLY:0    
       DEP-RES:NONE                 DEP-RES-DOWN-DLY:0
       DIAL-OUT:YES     RTY:LIN     NRTY:300    NRTY2:3      TB:3    
       CGO:#                        SGO:#                        
       CDO:99                       SDO:#                        
       - Tcp-MSS/Lcp/IpCp -----------------------------------------------------
       TCP-MSS-CLAMP:NO                                           DNS:NO
       - Authentication -------------------------------------------------------
       USERNAME:test
       PASSWORD:********                          LOCAL:CHAP,PAP
       SERVNAME:                                  REMOTE:NONE
       REPEAT:0

RES:Ip-100 - IP virtual (VIRTUAL) ---------------------------------------------
Run    DESCR:
       OPSTATE:UP             LOG:NO
       P-IP:1
       IPADD:192.168.001.101  MASK:255.255.255.000
       REDIS:YES     HIDE:NO         RP:NONE            IPSEC:(NO)     VRRP:NO
       NAT:(OUTSIDE)                 DIFFSERV:NO        DDNS:NO
       OUTBUF:100    OUTQUEUE:FAIR   MTU:1500           BRD:NET
       OUTSPL:NO

	Note
	The “Not Saved (SAVE CONF)” message is displayed every time the table is modified but not saved with the save conf command.

	Note
	The “Not Refreshed (INIT)” message is displayed every time the table is modified but not refreshed with the initialization command init res:ip.

By specifying IP resource identifier, the command will show the definition of the requested port. IP resource identifier must be in the interval [0 - 255]. If does not exist any resource with that identifier, an error message is generated: “RESOURCE NOT PRESENT OR INACTIVE”.

[08:38:13] ABILIS_CPX:d p ip-1

RES:Ip-1 - IP over LAN (LAN) --------------------------------------------------
Run    DESCR:LAN
       OPSTATE:UP             LOG:NO                 STATE-DETECT:NORMAL
       LANRES:Eth-1
       IPADD:192.168.029.254  MASK:255.255.255.000   
       REDIS:EXT     HIDE:NO         RP:NONE            IPSEC:NO       VRRP:NO
       NAT:INSIDE    UPNP:NO         DIFFSERV:NO        DDNS:NO
       OUTBUF:100    OUTQUEUE:FAIR   MTU:1500           BRD:NET
       OUTSPL:NO     
       INBUF:0                       mru:1500           SRCV:NO
       - TRFA section ---------------------------------------------------------
       TRFA:YES     TRFA-MODE:TOTALS       
       - Lan ------------------------------------------------------------------
       LLOG:NO       arpcache:200    CACHETIMER:120     rxbuf:4     txbuf:14
       VLAN-ID:UNTAG 
RES:Eth-1 ---------------------------------------------------------------------
Run    DESCR:
       LOG:DS            MODE:AUTO         DUPLEX:HALF   
       dma-rxbuf:250     dma-txbuf:25      max-vlans:0       
       ip-rxbuf:25       arp-rxbuf:5       pppoed-rxbuf:5    pppoes-rxbuf:25  

[14:47:53] ABILIS_CPX:d p ip-10

RESOURCE NOT PRESENT OR INACTIVE

Below the meaning of the most important parameters is shown:

IP over lan section

DESC

Resource description

OPSTATE

Operative state [DOWN, UP]

LOG

State changes log and alarm generation [NO, D, S, A, L, T, ALL] [+E] (D: Debug Log; S: System Log; A: Alarm view; L: Local audible alarm; T: SNMP traps; +E: Extended Log of state changes, see ref. manual)

STATE-DETECT

Select IP resource state detection method [NORMAL - the state depends on lower interface only; PING - the state depends on lower interface state and on result of the PING procedure. Enabling the PING procedure, the parameters of PING section are shown.

Refer to chapter Section 68.19, “How to use state detection of IP interfaces” to view a how to.

LANRES

Lower resource [NONE, Eth-XXX, EthUsb-XXX, VEth]

IPADD

IP address of the resource in DDN [0-126.x.x.x, 128-223.x.x.x] or "DHCP". IPADD and MASK can be configured together in Slash Notation, by means of IPADD:x.x.x.x/nn, with 'nn' in [0..32].

MASK

Mask in DDN [240.0.0.0 - 255.255.255.255]. The mask can also be configured with IPADD in Slash Notation, by means of IPADD:x.x.x.x/nn, with 'nn' in [0..32].

DHCP-DNS

Retrieve primary and secondary DNS server through DHCP [NO, YES] <Only for IPADD:DHCP>

DHCP-GW

Retrieve default gateway through DHCP [NO, YES] <Only for IPADD:DHCP>

DHCP-GW-AD

Administrative distance assigned to the default route obtained from a DHCP server [0..255] <Only for IPADD:DHCP>

REDIS

Create the related connected routing [NO: no route is created; YES: a destination route is added to IPR table, EXT: a source route is added to IPR table]

HIDE

Hide in RIP and OSPF updates [NO, YES]

RP

Routing protocols that will run on this interface [NONE, RIP, OSPF] Values can be joined using ',' character.

UPNP

Select UPNP mode [NO, LAN-CLIENT, LAN-SERVER, WAN] <Only for NAT:INSIDE/OUTSIDE>

DIFFSERV

Differentiated Services Field (DS) management [NO, NET, BORDER]

NAT

NAT usage [NO, INSIDE, OUTSIDE, VPN, DMZ]

IPSEC

Enable/disable IPSEC [NO, YES]

VRRP

Enable/disable VRRP [NO, YES]

DDNS

Enable/disable DDNS [NO, YES]

OUTBUF

Number of outgoing buffers [1..255]

OUTQUEUE

Output Queue management [FIFO, FAIR, SRCIP, DSTIP]

MTU

Maximum output IP datagram size [64..1500 bytes]

BRD

LAN broadcast treatment [NO, NET, LAN]

INBUF

Number of incoming buffers [0..255]

INQUEUE

Input queue management [FIFO, FAIR, SRCIP, DSTIP] <Only for INBUF: not equal to 0>

mru

Maximum input IP datagram size [1500 bytes]

SRCV

Source address validate [NO, YES]

OUTSPL

Output speed limitation activation [NO, YES, IPCOS]

OUTSP

Output speed limitation value [64..100000 Kbit/sec] <Only for OUTSPL: not equal to NO>

OUTSP-HIGH

Output speed limitation value in presence of HIGH priority traffic [64..100000 Kbit/sec] <Only for OUTSPL:IPCOS>

OUTSP-TOUT

Timeout to exit from OUTSP-HIGH: and return to OUTSP: [1..255 sec] <Only for OUTSPL:IPCOS>

INSPL

Input speed limitation activation [NO, YES, IPCOS, OUTSPL] <Only for INBUF: not equal to 0>

INSP

Input speed limitation value [64..100000 Kbit/sec] <Only for INSPL/OUTSPL: not equal to NO>

INSP-HIGH

Input speed limitation value in presence of HIGH priority traffic [64..100000 Kbit/sec] <Only for INSPL:OUTSPL/IPCOS-HIGH and OUTSPL:IPCOS-HIGH>

INSP-TOUT

Timeout to exit from INSP-HIGH: and return to INSP: [1..255 sec] <Only for INSPL:OUTSPL/IPCOS-HIGH and OUTSPL:IPCOS-HIGH>

SPL-OVERHEAD

Overhead added by lower layer drivers which is used by speed-limit procedure. "AUTO" or a couple of values "enc,line", where: - 'enc' is the encapsulation type and can be [RAW-IP, RAW-PPP, FR-IETF, FR-CISCO, HDLC-CISCO, RFC1483-VCMUX, RFC1483-LLCMUX, RFC2364-VCMUX, RFC2364-LLCMUX, PPPOE, PPPOE-BRIDGED]; - 'line' is the protocol type and can be [ETH, HDLC, AAL5] <Only for INSPL/OUTSPL: not equal to NO>

TRFA section:

TRFA

Enables/disables traffic analysis.

TRFA-MODE

Select traffic analysis mode [TOTALS: saves the total global traffic; PROT: subdivides the registration for the main protocol models; IP: saves the totals for every single IP address; IP-PROT: subdivides the traffic by protocol, for every single crossing IP address];

IP-RESERVE

Reserves records in the traffic analysis data base: it represents the maximum IP number trace.<Only for TRFA-MODE:IP/IP-PROT>

TRFA-SIDE

Selects IP address type [LOCAL: filters the traffic by destination IP address; REMOTE: filters the traffic by source IP address].<Only for TRFA-MODE:IP/IP-PROT>

TRFA-IPADD

IP address filter. <Only for TRFA-MODE:IP/IP-PROT>

- '*': any IP address

- 'LOCALNET': allowed only for TRFA-SIDE:LOCAL.

- a single IP address or two IP addresses separated by ':' (colon) [1.0.0.0-126.255.255.255, 128.0.0.0-223.255.255.255]

- the name of an IP/IR list between single quotes. (E.g.: * or LOCALNET or 150.1.1.1 or 192.1.0.0:192.1.0.9 or 'List')

Link section:

LCOMP: Set the compression type to use for an ip resource with subtype AIPT[-BCK], DL[-BCK], ML, BCH. Data Compression is available only under licence.[NO: compression not active, LZO1X: is often the best choice of all, LZO1B: is good with a large blocksize or with very redundant data, LZO1F: s good with a small blocksize or with binary data]

RIP section:

RIPSEND: Protocol used for sending updates [RIP1, RIP2B, RIP2M, NO] <Only for RP:RIP or RP:RIP,OSPF>
RIPRECV: Protocol accepted for receiving updates [RIP1, RIP2, BOTH, NO] <Only for RP:RIP or RP:RIP,OSPF>
RIPNU: Selection of normal updates vs. triggered updates [NO, YES] <Only for RP:RIP or RP:RIP,OSPF>
RIPMETRIC: Assigned RIP metric [0..16] <Only for RP:RIP or RP:RIP,OSPF>

OSPF section:

OAREA: Area ID which this IP port belongs to [#, 0.0.0.0-255.255.255.255] <Only for RP:OSPF or RP:RIP,OSPF>
ONETTYPE: Type of network [BN, NBMA, PP, PMP] <Only for RP:OSPF or RP:RIP,OSPF>
OPRIO: Interface priority [0..255] <Only for RP:OSPF or RP:RIP,OSPF>
OCOST: OSPF output cost [1..65535] <Only for RP:OSPF or RP:RIP,OSPF>
ORXMT: Retransmission interval [1..150 sec] <Only for RP:OSPF or RP:RIP,OSPF>
OTRDEL: Transmit delay interval [1..30 sec] <Only for RP:OSPF or RP:RIP,OSPF>
OHELLO: Hello interval [1..120 sec] <Only for RP:OSPF or RP:RIP,OSPF>
ODEAD: Router dead interval [1..1200 sec] <Only for RP:OSPF or RP:RIP,OSPF>
omax-nei: Maximum number of neighbors [0..255] <Only for RP:OSPF or RP:RIP,OSPF>
OREM-RID: Remote Router ID [0.0.0.0-255.255.255.255] <Only for RP:OSPF or RP:RIP,OSPF>
OPWD: Authentication password. From 0 up to 8 ASCII characters. Spaces are not allowed. <Only for AUTTYPE:SIMPLE><Only for RP:OSPF or RP:RIP,OSPF>
OKEYID: Key ID [0..255] <Only for AUTTYPE:CRYPTO> <Only for RP:OSPF or RP:RIP,OSPF>
OMD5KEY: MD5 secret key. From 0 up to 16 ASCII characters. Spaces are not allowed. <Only for AUTTYPE:CRYPTO><Only for RP:OSPF or RP:RIP,OSPF>

DDNS section:

DDNS-FQDN: DDNS domain name. From 0 up to 64 characters in the range ['0'..'9', 'a'..'z', '-', '.']. Case is not preserved. <Only for DDNS:YES>

Lan section:

LLOG: State changes log and alarm generation [NO, D, S, A, L, T, ALL] [+E] (D: Debug Log; S: System Log; A: Alarm view; L: Local audible alarm; T: SNMP traps; +E: Extended Log of state changes, see ref. manual)
arpcache: Size of the ARP cache [200..2000]
CACHETIMER: Lifetime of an item in the cache [15..65535 sec]
rxbuf: Number of receive buffers [1..255]
txbuf: Number of transmit buffers [1..255]
VLAN-ID: VLAN Identifier [0, 1..4094, UNTAG] <Only for LANRES:Eth>
PRIO-ARP: ARP priority over VLAN [0..7] <Only for VLAN-ID <> UNTAG>

PING section:

P-LOC: Source IP address used for PING request (ECHO REQUEST) [1-126.x.x.x, 127.0.0.1, 128-223.x.x.x] or "R-ID" or "IPADD".
P-DST1: Ip address of the destination number 1 [1-126.x.x.x, 127.0.0.1, 128-223.x.x.x] or "#".
P-DST2: Ip address of the destination number 2 [1-126.x.x.x, 127.0.0.1, 128-223.x.x.x] or "#".
P-GW: Ip address of the gateway [1-126.x.x.x, 127.0.0.1, 128-223.x.x.x] or "#".
P-TOUT: Timeout for the reply reception (ECHO REPLY) [100..10000 msec].
P-TRY: Number of attempts considered for the state detection [2..50].
P-DLY-UP: Interval between attempts while state is UP [1..60 sec].
P-DLY-UP: Interval between attempts while state is UP [1..60 sec].
P-DLY-DN: Interval between attempts while state is DOWN [1..60 sec].
P-THR-UP: Percentage of successful attempts to declare state UP [10..100].
P-THR-DN: Percentage of successful attempts to declare state DOWN [0..90].
P-BURST: Number of requests sent at each attempt [1..10].
P-BURST-DLY: Interval between requests pertaining to the same attempt [0..1000 msec].
P-TTL: TTL value when transport layer doesn't provide one [DFT, 1..255].

20.3.2. A RES:IP (Add IP Resource)

It adds a new IP resource, identified by “IP-xx”.

Type the following command to display all the available types of IP resource.

[10:16:34] ABILIS_CPX:a res:ip ?

Ip resource subtypes:

X25PVC          IP over X.25 Pvc
X25BSVC         IP over X.25 Bsvc
LAN             IP over LAN
DL              IP over Dedicated Line
DL-BCK          IP over Dedicated Line with Abilis Back-up
BCH             IP over B-Channel
ML              IP over Multi-Links
AIPT            IP over IP (Abilis tunnel)
AIPT-BCK        IP over IP (Abilis tunnel) with Abilis Back-up
PPP             IP over PPP
VIRTUAL         IP virtual

Some examples follow:

[12:18:12] ABILIS_CPX:a res:ip-10 subtype:lan

COMMAND EXECUTED

[12:18:20] ABILIS_CPX:d p ip-10

RES:Ip-10 - Not Running, Not Saved (SAVE CONF) --------------------------------
       - IP over LAN (LAN) ----------------------------------------------------
New    DESCR:
       OPSTATE:UP             LOG:NO                 STATE-DETECT:NORMAL
       LANRES:NONE
       IPADD:000.000.000.000  MASK:255.255.255.255   
       REDIS:EXT     HIDE:NO         RP:NONE            IPSEC:NO       VRRP:NO
       NAT:NO                        DIFFSERV:NO        DDNS:NO
       OUTBUF:100    OUTQUEUE:FAIR   MTU:1500           BRD:NET
       OUTSPL:NO     
       INBUF:0                       mru:1500           SRCV:NO
       - TRFA section ---------------------------------------------------------
       TRFA:NO      
       - Lan ------------------------------------------------------------------
       LLOG:NO       arpcache:200    CACHETIMER:120     rxbuf:4     txbuf:14

[12:18:23] ABILIS_CPX:a res:ip-11 subtype:aipt

COMMAND EXECUTED

[12:22:13] ABILIS_CPX:d p ip-11

RES:Ip-11 - Not Running, Not Saved (SAVE CONF) --------------------------------
       - IP over IP (Abilis tunnel) (AIPT) ------------------------------------
New    DESCR:
       OPSTATE:UP             LOG:NO                 STATE-DETECT:NORMAL
                              FRAG:NO                
       IPADD:000.000.000.000  MASK:255.255.255.255   NEIGH:000.000.000.000
       REDIS:YES     HIDE:NO         RP:NONE            IPSEC:NO       VRRP:NO
       NAT:NO                        DIFFSERV:NO        DDNS:NO
       OUTBUF:100    OUTQUEUE:FAIR   MTU:1500           
       OUTSPL:NO     
       INBUF:0                       mru:1500           SRCV:NO
       - TRFA section ---------------------------------------------------------
       TRFA:NO      
       - Link -----------------------------------------------------------------
       LLOG:DS       LMPX:YES         LC:YES         LCOMP:NO      LCR:NO
       LT1:3000      LT3:9000         LN2:3                        LCRKEY:DFT
       - IP Tunnel ------------------------------------------------------------
       TLOG:NO       MODE:EXT         D-TOS:0-N      V-TOS:0-D     C-TOS:0-D  
       MPX:NO        RS-BUF:100       D-TOUT:1000    V-TOUT:100    V-RED:NONE
       PATH:SINGLE   LOCPORT:2111     REMPORT:2100   CR:NO         CRKEY:DFT
       OUT-IP:AUTO                                  
       LOCIPADD:OUT-IP                  REMIPADD:#


[12:23:06] ABILIS_CPX:a res:ip-12 subtype:dl

COMMAND EXECUTED

[12:23:31] ABILIS_CPX:d p ip-12

RES:Ip-12 - Not Running, Not Saved (SAVE CONF) --------------------------------
       - IP over Dedicated Line (DL) ------------------------------------------
New    DESCR:
       OPSTATE:UP             LOG:NO                 STATE-DETECT:NORMAL
       LOWRES:NONE
       ENC:RAW-IP             FRAG:NO                
       IPADD:000.000.000.000  MASK:255.255.255.255   NEIGH:000.000.000.000
       REDIS:YES     HIDE:NO         RP:NONE            IPSEC:NO       VRRP:NO
       NAT:NO                        DIFFSERV:NO        DDNS:NO
       OUTBUF:100    OUTQUEUE:FAIR   MTU:1500           
       OUTSPL:NO     
       INBUF:0                       mru:1500           SRCV:NO
       - TRFA section ---------------------------------------------------------
       TRFA:NO      
       - Link -----------------------------------------------------------------
       LLOG:DS       LMPX:NO                         LCOMP:NO      LCR:NO
       LT1:1000      LT3:3000         LN2:3                        LCRKEY:DFT

	Caution
	After adding a new IP resource, you must restart the Abilis to make the resource running (use the command warm start to reboot the Abilis).

	Tip
Interesting chapters: Section 68.2, “How to activate a new ethernet port”; Section 68.3, “How to assign several IP addresses to the same LAN port”.

Tip

Interesting chapters:

Section 68.2, “How to activate a new ethernet port”;

Section 68.3, “How to assign several IP addresses to the same LAN port”.

20.3.3. C RES:IP (Clear IP Resource)

It removes the requested IP resource from the IP resources table.

	Caution
	It's not possible to remove an IP resource on a running CPX with this command! It's needed to follow this sequence: Deactivate the IP resource with s inact res:ip-x command. Save the configuration with save conf command. Reboot the Abilis with the warm start command. Clear permanently the IP resource with c res:ip-x command.

[08:50:03] ABILIS_CPX:d p ip-5

RES:Ip-5 - IP over IP (Abilis tunnel) (AIPT) ----------------------------------
Run    DESCR:
       OPSTATE:UP             LOG:NO                 STATE-DETECT:NORMAL
                              FRAG:NO                
       IPADD:000.000.000.000  MASK:255.255.255.255   NEIGH:000.000.000.000
       REDIS:YES     HIDE:NO         RP:NONE            IPSEC:NO       VRRP:NO
       NAT:NO                        DIFFSERV:NO        DDNS:NO
       OUTBUF:100    OUTQUEUE:FAIR   MTU:1500           
       OUTSPL:NO     
       INBUF:0                       mru:1500           SRCV:NO
       - TRFA section ---------------------------------------------------------
       TRFA:NO      
       - Link -----------------------------------------------------------------
       LLOG:DS       LMPX:YES         LC:YES         LCOMP:NO      LCR:NO
       LT1:3000      LT3:9000         LN2:3                        LCRKEY:DFT
       - IP Tunnel ------------------------------------------------------------
       TLOG:NO       MODE:EXT         D-TOS:0-N      V-TOS:0-D     C-TOS:0-D  
       MPX:NO        RS-BUF:100       D-TOUT:1000    V-TOUT:100    V-RED:NONE
       PATH:SINGLE   LOCPORT:2105     REMPORT:2100   CR:NO         CRKEY:DFT
       OUT-IP:AUTO                                  
       LOCIPADD:OUT-IP                  REMIPADD:#

[08:50:08] ABILIS_CPX:c res:ip-5

COMMAND NOT ALLOWED FOR 'RES:IP-5' BECAUSE IT IS RUNNING

[08:55:03] ABILIS_CPX:s inact res:ip-5

COMMAND EXECUTED

[08:55:25] ABILIS_CPX:save conf

VALIDATION IN PROGRESS ...
VALIDATION SUCCESSFULLY EXECUTED

SAVE EXECUTED

[15:07:05] ABILIS_CPX:warm start

At next reboot:

[08:58:31] ABILIS_CPX:c res:ip-5

THE SELECTED RESOURCE WILL BE DELETED.
PROCEED (N/Y)?y

THE COMMAND WILL DELETE ALL THE REFERENCES TO THE SELECTED RESOURCE.
PROCEED ANYWAY (N/Y)?y

PROCEEDING WITH RESOURCE DELETION...

COMMAND EXECUTED

	Warning
	Deleting an IP resource also its references in IPR, IPACL , IPAD and RIP EXTERNAL will be deleted!!

20.3.4. S P IP (Set Parameter IP Resource)

It sets the parameters to their new values for the specified IP resource. Parameters of each IP resource can be separately configured depending of the connection.

The syntax of the command is:

s p ip-x [par:val...]

In the example below description, neighbour IP (NEIGH), subnet mask (MASK), LOCIPADD and REMIPADD parameters will be modified.

[09:00:43] ABILIS_CPX:d p ip-8

RES:Ip-8 - IP over IP (Abilis tunnel) (AIPT) ----------------------------------
Run    DESCR:
       OPSTATE:UP             LOG:NO                 STATE-DETECT:NORMAL
                              FRAG:NO                
       IPADD:000.000.000.000  MASK:255.255.255.255   NEIGH:000.000.000.000
       REDIS:YES     HIDE:NO         RP:NONE            IPSEC:NO       VRRP:NO
       NAT:NO                        DIFFSERV:NO        DDNS:NO
       OUTBUF:100    OUTQUEUE:FAIR   MTU:1500           
       OUTSPL:NO     
       INBUF:0                       mru:1500           SRCV:NO
       - TRFA section ---------------------------------------------------------
       TRFA:NO      
       - Link -----------------------------------------------------------------
       LLOG:DS       LMPX:YES         LC:YES         LCOMP:NO      LCR:NO
       LT1:3000      LT3:9000         LN2:3                        LCRKEY:DFT
       - IP Tunnel ------------------------------------------------------------
       TLOG:NO       MODE:EXT         D-TOS:0-N      V-TOS:0-D     C-TOS:0-D  
       MPX:NO        RS-BUF:100       D-TOUT:1000    V-TOUT:100    V-RED:NONE
       PATH:SINGLE   LOCPORT:2108     REMPORT:2100   CR:NO         CRKEY:DFT
       OUT-IP:AUTO                                  
       LOCIPADD:OUT-IP                  REMIPADD:#

[09:01:18] ABILIS_CPX:s p ip-8 descr:To_Abilis_2 neigh:192.168.2.254 mask:255.255.255.0 locipadd:217.1.1.1 remipadd:217.2.2.2

COMMAND EXECUTED

[09:01:25] ABILIS_CPX:d p ip-8

RES:Ip-8 - Not Saved (SAVE CONF), Not Refreshed (INIT) ------------------------
       - IP over IP (Abilis tunnel) (AIPT) ------------------------------------
Run    DESCR:To_Abilis_2
       OPSTATE:UP             LOG:NO                 STATE-DETECT:NORMAL
                              FRAG:NO                
       IPADD:000.000.000.000  MASK:255.255.255.000   NEIGH:192.168.002.254
       REDIS:YES     HIDE:NO         RP:NONE            IPSEC:NO       VRRP:NO
       NAT:NO                        DIFFSERV:NO        DDNS:NO
       OUTBUF:100    OUTQUEUE:FAIR   MTU:1500           
       OUTSPL:NO     
       INBUF:0                       mru:1500           SRCV:NO
       - TRFA section ---------------------------------------------------------
       TRFA:NO      
       - Link -----------------------------------------------------------------
       LLOG:DS       LMPX:YES         LC:YES         LCOMP:NO      LCR:NO
       LT1:3000      LT3:9000         LN2:3                        LCRKEY:DFT
       - IP Tunnel ------------------------------------------------------------
       TLOG:NO       MODE:EXT         D-TOS:0-N      V-TOS:0-D     C-TOS:0-D  
       MPX:NO        RS-BUF:100       D-TOUT:1000    V-TOUT:100    V-RED:NONE
       PATH:SINGLE   LOCPORT:2108     REMPORT:2100   CR:NO         CRKEY:DFT
       OUT-IP:AUTO                                  
       LOCIPADD:217.001.001.001         REMIPADD:217.002.002.002

20.3.5. Examples

The following paragraphs contain some examples to explain the meaning of REDIS parameter.

20.3.5.1. Examples of REDIS parameter use

The REDIS parameter manages the entry in the IPR table for the specific ip resource. The following table shows the meaning of values:

`NO`	No entry is created in the IPR table. Creating a route by hand is needed to use the ip resource.
`YES`	A destination routing with the IPADD of the IP resource is automatically added in the routing table.
`EXT`	A source routing with the IPADD of the IP resource is automatically added in the routing table.

	Note
	REDIS:`NO` can be always used, but every route must be created by hand.

Examples:

The parameter REDIS of ip-2 i set to NO, so in the ipr table there's no entry automatically generated and related with this ip address. If you want to use the ip-2 as gateway you must add a route by hand.

[15:34:07] ABILIS_CPX:_d p ip-2

RES:Ip-2 - Not Saved (SAVE CONF) ----------------------------------------------
       - IP over LAN (LAN) ----------------------------------------------------
Run    DESCR:WAN
       OPSTATE:UP             LOG:NO               STATE-DETECT:NORMAL
       LANRES:Eth-2
       IPADD:DHCP    DHCP-GW:YES     DHCP-GW-AD:0       DHCP-DNS:YES
       REDIS:NO      HIDE:NO         RP:NONE            IPSEC:NO       VRRP:NO
       NAT:OUTSIDE   UPNP:NO         DIFFSERV:NO        DDNS:NO
       OUTBUF:100    OUTQUEUE:FAIR   MTU:1500           BRD:NET
       OUTSPL:NO     
       INBUF:0                       mru:1500           SRCV:NO
       - TRFA section ---------------------------------------------------------
       TRFA:YES     TRFA-MODE:IP-PROT      IP-RESERVE:AUTO     TRFA-SIDE:REMOTE
       TRFA-IPADD:*
       - Lan ------------------------------------------------------------------
       LLOG:NO       arpcache:200    CACHETIMER:120     rxbuf:4     txbuf:14
       VLAN-ID:UNTAG 
RES:Eth-2 ---------------------------------------------------------------------
Run    DESCR:
       LOG:DS            MODE:AUTO         DUPLEX:HALF   
       dma-rxbuf:250     dma-txbuf:25      max-vlans:0       
       ip-rxbuf:25       arp-rxbuf:5       pppoed-rxbuf:5    pppoes-rxbuf:25

[15:34:22] ABILIS_CPX:_d d ip-2

RES:Ip-2 - IP over LAN (LAN) --------------------------------------------------
       WAN
       STATE:UP              LINK-STATE:LINKREADY
       CUR-IPADD:192.168.001.100    CUR-MASK:255.255.255.000
       OUTBUF:100   S-OUTBUF:500    CUR-OUTSP:N/A      OUTSP-TOUT:N/A   
       INBUF:0      S-INBUF:0       CUR-INSP:N/A       INSP-TOUT:N/A   
       SPL-OVERHEAD:RAW-IP,ETH
       - Lan ------------------------------------------------------------------
       STATE:LINKREADY       ARP-CACHE-ITEMS:1         VLAN-ID:UNTAG


[15:34:25] ABILIS_CPX:_d ipr

- Not Saved (SAVE CONF) -------------------------------------------------------

Destination routes and conditional source routes:
+-+-+-+-+--------------------+--------------------+-----------------+----+---+
|B|P|S|H|     NET:/MASK:     |      MASK: or      |       GW: or    |IP: |AD:|
| | | | |                    |   SRNET:/SRMASK:   |      IPLB:      |    |   |
+-+-+-+-+--------------------+--------------------+-----------------+----+---+
|*|C| |*| 127.000.000.001/32 | 255.255.255.255    |                 |LOOP|  0|
|*|C| | | 192.168.030.001/32 | 255.255.255.255    |                 |R-ID|  0|
|*|C| | | 010.000.000.000/29 | 255.255.255.248    |                 |  12|  0|
|*|C| | | 192.168.000.000/24 | 255.255.255.000    |                 |  11|  0|
|*|S| | | 192.168.008.000/24 | 255.255.255.000    |                 |D 10|  1|
|*|C| | | 192.168.030.000/24 | 255.255.255.000    |                 |   1|  0|
+-+-+-+-+--------------------+--------------------+-----------------+----+---+

The parameter REDIS of ip-2 is set to YES, so in the ipr table there's an entry with provenience equal to C (refer to Section 20.2.1, “D IPR (Display IP Routing)”). The route automatically created is a destination route.

[15:38:00] ABILIS_CPX:_d p ip-2

RES:Ip-2 - Not Saved (SAVE CONF) ----------------------------------------------
       - IP over LAN (LAN) ----------------------------------------------------
Run    DESCR:WAN
       OPSTATE:UP             LOG:NO               STATE-DETECT:NORMAL
       LANRES:Eth-2
       IPADD:DHCP    DHCP-GW:YES     DHCP-GW-AD:0       DHCP-DNS:YES
       REDIS:YES     HIDE:NO         RP:NONE            IPSEC:NO       VRRP:NO
       NAT:OUTSIDE   UPNP:NO         DIFFSERV:NO        DDNS:NO
       OUTBUF:100    OUTQUEUE:FAIR   MTU:1500           BRD:NET
       OUTSPL:NO     
       INBUF:0                       mru:1500           SRCV:NO
       - TRFA section ---------------------------------------------------------
       TRFA:YES     TRFA-MODE:IP-PROT      IP-RESERVE:AUTO     TRFA-SIDE:REMOTE
       TRFA-IPADD:*
       - Lan ------------------------------------------------------------------
       LLOG:NO       arpcache:200    CACHETIMER:120     rxbuf:4     txbuf:14
       VLAN-ID:UNTAG 
RES:Eth-2 ---------------------------------------------------------------------
Run    DESCR:
       LOG:DS            MODE:AUTO         DUPLEX:HALF   
       dma-rxbuf:250     dma-txbuf:25      max-vlans:0       
       ip-rxbuf:25       arp-rxbuf:5       pppoed-rxbuf:5    pppoes-rxbuf:25
[15:38:22] ABILIS_CPX:_d d ip-2

RES:Ip-2 - IP over LAN (LAN) --------------------------------------------------
       WAN
       STATE:UP              LINK-STATE:LINKREADY
       CUR-IPADD:192.168.001.100    CUR-MASK:255.255.255.000
       OUTBUF:100   S-OUTBUF:500    CUR-OUTSP:N/A      OUTSP-TOUT:N/A   
       INBUF:0      S-INBUF:0       CUR-INSP:N/A       INSP-TOUT:N/A   
       SPL-OVERHEAD:RAW-IP,ETH
       - Lan ------------------------------------------------------------------
       STATE:LINKREADY       ARP-CACHE-ITEMS:1         VLAN-ID:UNTAG

[15:38:25] ABILIS_CPX:_d ipr

- Not Saved (SAVE CONF) -------------------------------------------------------

Destination routes and conditional source routes:
+-+-+-+-+--------------------+--------------------+-----------------+----+---+
|B|P|S|H|     NET:/MASK:     |      MASK: or      |       GW: or    |IP: |AD:|
| | | | |                    |   SRNET:/SRMASK:   |      IPLB:      |    |   |
+-+-+-+-+--------------------+--------------------+-----------------+----+---+
|*|C| |*| 127.000.000.001/32 | 255.255.255.255    |                 |LOOP|  0|
|*|C| | | 192.168.030.001/32 | 255.255.255.255    |                 |R-ID|  0|
|*|C| | | 010.000.000.000/29 | 255.255.255.248    |                 |  12|  0|
|*|C| | | 192.168.000.000/24 | 255.255.255.000    |                 |  11|  0|
|*|C| | | 192.168.001.000/24 | 255.255.255.000    |                 |   2|  0|
|*|S| | | 192.168.008.000/24 | 255.255.255.000    |                 |D 10|  1|
|*|C| | | 192.168.030.000/24 | 255.255.255.000    |                 |   1|  0|
|*|C| | | 000.000.000.000/0  | 000.000.000.000    | 192.168.001.001 |   2|  0|
+-+-+-+-+--------------------+--------------------+-----------------+----+---+

The parameter REDIS of ip-2 is set to EXT, so in the ipr table there's an entry with provenience equal to C (refer to Section 20.2.1, “D IPR (Display IP Routing)”). Two routes are automatically created: a destination route and a default route for that ip address.

Setting REDIS:EXT is useful to automatically generate a route when using two or more ADSL lines.

[15:27:59] ABILIS_CPX:_d p ip-2

RES:Ip-2 - Not Saved (SAVE CONF) ----------------------------------------------
       - IP over LAN (LAN) ----------------------------------------------------
Run    DESCR:WAN
       OPSTATE:UP             LOG:NO               STATE-DETECT:NORMAL
       LANRES:Eth-2
       IPADD:DHCP    DHCP-GW:YES     DHCP-GW-AD:0       DHCP-DNS:YES
       REDIS:EXT     HIDE:NO         RP:NONE            IPSEC:NO       VRRP:NO
       NAT:OUTSIDE   UPNP:NO         DIFFSERV:NO        DDNS:NO
       OUTBUF:100    OUTQUEUE:FAIR   MTU:1500           BRD:NET
       OUTSPL:NO     
       INBUF:0                       mru:1500           SRCV:NO
       - TRFA section ---------------------------------------------------------
       TRFA:YES     TRFA-MODE:IP-PROT      IP-RESERVE:AUTO     TRFA-SIDE:REMOTE
       TRFA-IPADD:*
       - Lan ------------------------------------------------------------------
       LLOG:NO       arpcache:200    CACHETIMER:120     rxbuf:4     txbuf:14
       VLAN-ID:UNTAG 
RES:Eth-2 ---------------------------------------------------------------------
Run    DESCR:
       LOG:DS            MODE:AUTO         DUPLEX:HALF   
       dma-rxbuf:250     dma-txbuf:25      max-vlans:0       
       ip-rxbuf:25       arp-rxbuf:5       pppoed-rxbuf:5    pppoes-rxbuf:25

[15:28:21] ABILIS_CPX:_d d ip-2

RES:Ip-2 - IP over LAN (LAN) --------------------------------------------------
       WAN
       STATE:UP              LINK-STATE:LINKREADY
       CUR-IPADD:192.168.001.100    CUR-MASK:255.255.255.000
       OUTBUF:100   S-OUTBUF:500    CUR-OUTSP:N/A      OUTSP-TOUT:N/A   
       INBUF:0      S-INBUF:0       CUR-INSP:N/A       INSP-TOUT:N/A   
       SPL-OVERHEAD:RAW-IP,ETH
       - Lan ------------------------------------------------------------------
       STATE:LINKREADY       ARP-CACHE-ITEMS:1         VLAN-ID:UNTAG

[15:29:05] ABILIS_CPX:_d ipr

- Not Saved (SAVE CONF) -------------------------------------------------------

Destination routes and conditional source routes:
+-+-+-+-+--------------------+--------------------+-----------------+----+---+
|B|P|S|H|     NET:/MASK:     |      MASK: or      |       GW: or    |IP: |AD:|
| | | | |                    |   SRNET:/SRMASK:   |      IPLB:      |    |   |
+-+-+-+-+--------------------+--------------------+-----------------+----+---+
|*|C| |*| 127.000.000.001/32 | 255.255.255.255    |                 |LOOP|  0|
|*|C| | | 192.168.030.001/32 | 255.255.255.255    |                 |R-ID|  0|
|*|C| | | 010.000.000.000/29 | 255.255.255.248    |                 |  12|  0|
|*|C| | | 192.168.000.000/24 | 255.255.255.000    |                 |  11|  0|
|*|C| | | 192.168.001.000/24 | 255.255.255.000    |                 |   2|  0|
|*|S| | | 192.168.008.000/24 | 255.255.255.000    |                 |D 10|  1|
|*|C| | | 192.168.030.000/24 | 255.255.255.000    |                 |   1|  0|
|*|C| | | 000.000.000.000/0  | 000.000.000.000    | 192.168.001.001 |   2|  0|
| |C| | |                    |[192.168.001.100/32]| 192.168.001.001 |   2|   |
+-+-+-+-+--------------------+--------------------+-----------------+----+---+


20.2. IP Routings table		20.4. Administrative Distance