| 5.7. Initialization/activation/deactivation commands | ||
|---|---|---|
 | Chapter 5. Command language |  |
| 5.7. Initialization/activation/deactivation commands | ||
|---|---|---|
| | Chapter 5. Command language | |
These commands allow to reinitialize and active parameters modified on ports and resources written in upper case characters or refresh any tables updating. The following command allows to display the command syntax:
[12:45:38] ABILIS_CPX:init ?ALARM Refreshes Alarm resource and Alarm rules CTIG Unsupported. Use INIT CTIR to refresh CTI groups CTIR Refreshes CTI routings and CTI groups CTISYS Refreshes parameters of CTISYS resource (RES:CtiSys) and refreshes entries in CTI ports, links, clusters and LCS groups It refreshes NPv resource and links too (if Npv is running). CTIVR Refreshes CTI VR rules IP Refreshes IP router, IP resources and purges queues, refreshes IP administrative distances, load balancing and rebuilds IP Routings table. IPAD Refreshes IP Routing Administrative Distances IPBAN Refreshes IP addresses banning management rules IPLB Refreshes IP Load Balancing definitions IPR Rebuilds IP Routings table IPSH Refreshes IP Shaping flows and rules tables LCSG Unsupported. Use INIT CTISYS to refresh LCS groups LDAP Refreshes LDAP Accounts and/or Referrals tables NAT Refreshes static table and clears dynamic table RES: Refreshes parameters of a resource TRFA Refreshes TRFA IP or CTI Traps USBDEV Refreshes USB Service
For example, to initialize the CTI Routing table:
[12:45:39] ABILIS_CPX:init ctirCOMMAND EXECUTED
The command init res: initializes the specified resource(s), if it is currently active and running. At the same time the command updates configuration parameters that have been modified, activating them. The following command allows to display the command syntax:
[12:45:39] ABILIS_CPX:init res: ?INIT RES:A Refresh parameter(s) of any resource. INIT RES:type Refresh parameter(s) of any resource of the specified type. INIT RES:type-n Refresh parameter(s) of the specified resource.
The command will work on present, active and running resources only; otherwise the error message “RESOURCE NOT PRESENT OR INACTIVE” will be displayed.
This command displays all the cards and resources currently configured and active. Cards and resources are active, if they are configured (present), but not necessarily running.
Setting changes and visualization are allowed only for active card and resources. Cards and resources are running only if they are configured (present) and active when the system starts.
Here is an example of the command execution:
[11:38:04] ABILIS_CPX:d act------------------ Active PCI Devices and Physical Resources: ----------------- Device(s) Run Physical Resource(s) or CTI Port(s) SlotId Addr Irq ------------------------------------------------------------------------------- ASY-1 Yes Async-1 . . . . . . . . . . . . . . . . . . - 3F8 4 ETH-1 Yes Eth-1 . . . . . . . . . . . . . . . . . . . 64 PCI ( 18) ETH-2 Yes Eth-2 . . . . . . . . . . . . . . . . . . . 96 PCI ( 17) ETH-3 Yes Eth-3 . . . . . . . . . . . . . . . . . . . 128 PCI ( 16) BRI4-2 Yes 35..38 . . . . . . . . . . . . . . . . . . . 161 PCI ( 22) POTS-1 Yes 101..116 . . . . . . . . . . . . . . . . . . 160 PCI ( 21) POTS-2 Yes 117..132 . . . . . . . . . . . . . . . . . . 162 PCI ( 23) VPOTS-5 Yes 165..180 . . . . . . . . . . . . . . . . . . - PCI ( -) CELL32-1 Yes 501..532 . . . . . . . . . . . . . . . . . . - PCI ( -) ------------------ Active USB Devices and Physical Resources: ----------------- Device(s) Run Con Physical Resource(s) or CTI Port(s) USBPORTID ------------------------------------------------------------------------------- UPS-1 Yes No Ups . . . . . . . . . . . . . . . . . NONE ADSLUSB-1 Yes Yes Adsl-1 . . . . . . . . . . . . . . . . 1.0 ADSLUSB-2 Yes No Adsl-2 . . . . . . . . . . . . . . . . 0.3 CELLBOX-1 501..502 . . . . . . . . . . . . . . . CELL-1 Yes Yes . . . . . . . . . . . . . . . . . . . 0.2.0 CELL-2 Yes Yes . . . . . . . . . . . . . . . . . . . 0.2.1 CODEC-1 Yes Yes . . . . . . . . . . . . . . . . . . . 0.2.2 CONTROL-1 Yes Yes . . . . . . . . . . . . . . . . . . . 0.2.3 CELLBOX-2 503..504 . . . . . . . . . . . . . . . CELL-3 Yes No . . . . . . . . . . . . . . . . . . . 1.1.0 CELL-4 Yes No . . . . . . . . . . . . . . . . . . . 1.1.1 CODEC-2 Yes No . . . . . . . . . . . . . . . . . . . 1.1.2 CONTROL-2 Yes No . . . . . . . . . . . . . . . . . . . 1.1.3 GPIO-1 Yes Yes Gpio-1 . . . . . . . . . . . . . . . . 3.1 GPIO-2 Yes No Gpio-2 . . . . . . . . . . . . . . . . 6.0 BLUSB-1 Yes No Blusb-1 . . . . . . . . . . . . . . . - -------------------------- Active System Resource(s) -------------------------- Type Resource(s) ------------------------------------------------------------------------------- Blusb 1 Gpio 1 2 Arc 1 Ssl 1 Mf 1 MfIo 1 MfTemp 1 SysCtl 1 Vs 1 Ups 1 ------------------------ Active Management Resource(s) ------------------------ Type Resource(s) ------------------------------------------------------------------------------- Cp 1 Snmp 1 Sntp 1 Acnt 1 Trfa 1 SysLog 1 Opc 1 GpioPc 1 Alarm 1 Script 1 ---------------- Active Connection Oriented Router Resource(s) ---------------- Type Resource(s) ------------------------------------------------------------------------------- X25 1 2 999 Pad 1 ---------------------------- Active IP Resource(s) ---------------------------- Type Resource(s) ------------------------------------------------------------------------------- Iprtr 1 Tcp 1 Udp 1 Telnet 1 Dns 1 Http 1 Nat 1 Ssh 1 Ftp 1 Smtp 1 IpSh 1 Ip 1 2 3 4 10 14 15 200 ---------------- Active PPP over Ethernet Resource(s) -------------------------- Type Resource(s) ------------------------------------------------------------------------------- PoeAc 1 PoeCli 1 --------------------------- Active CTI Resource(s) ---------------------------- Type Resource(s) ------------------------------------------------------------------------------- CtiSLink 1 CtiSys 1 CtiIax 1 CtiDisa 1 CtiSip 1 CtiSms 1 CtiAs 1 CtiVm 1 CtiVr 1 CtiMix 1 CtiVo 1 ----------------------- Active Frame Relay Resource(s) ------------------------ Type Resource(s) ------------------------------------------------------------------------------- *** NO ACTIVE FRAME RELAY RESOURCEs PRESENT *** ------------------------ Active Pv and Ple Resource(s) ----------------------- Type Resource(s) ------------------------------------------------------------------------------- Pv 3 5 6 9 12 14 16 17 18 19 20 26 28 31 33 38 39 49 53 59 NPv 1 -------------------- Active Physical Communication Resource(s) ---------------- Type Resource(s) ------------------------------------------------------------------------------- Async 1 Eth 1 2 3 Adsl 1 2
These commands set active the specified card(s) or resource(s). The following command allows to display the command syntax:
[12:45:39] ABILIS_CPX:s act ?CTIP: CTI port identifier [1..600] DEV: HW device identifier 'type-n', where 'n' can be [1..255] RES: Resource identifier 'type-n', where 'n' can be [1..999]
![[Warning]](../images/warning.png) | Warning |
|---|---|
Activating a card or a resource does not mean to make it run. Activation makes possible to show card's/resource's parameters and to modify them. To have a running card/resource or activate the changes made on the card/resource, it is needed to save the configuration (use the command save conf ) and restart the system (use the command warm start ). |
This command shows all the cards and resources currently configured but inactive. A card (resource) is inactive (or not active) when it is present but it is not running.
Setting changes and visualization are not allowed for inactive cards/resources. Moreover configured but inactive cards/resources are ignored when the system starts.
[11:38:04] ABILIS_CPX:d inact----------------- Inactive PCI Devices and Physical Resources: ---------------- Card(s) Run Physical Resource(s)/CTI Port(s) SlotId Addr Irq ------------------------------------------------------------------------------- BRI4-1 No 31..34 . . . . . . . . . . . . . . . . . . . . NONE PCI ( -) ----------------- Inactive USB Devices and Physical Resources: ---------------- Device(s) Run Con Physical Resource(s) or CTI Port(s) USBPORTID ------------------------------------------------------------------------------- *** NO INACTIVE USB DEVICEs PRESENT *** ------------------------- Inactive System Resource(s) ------------------------- Type Resource(s) ------------------------------------------------------------------------------- *** NO INACTIVE SYSTEM RESOURCEs PRESENT *** ----------------------- Inactive Management Resource(s) ----------------------- Type Resource(s) ------------------------------------------------------------------------------- *** NO INACTIVE MANAGEMENT RESOURCEs PRESENT *** --------------- Inactive Connection Oriented Router Resource(s) --------------- Type Resource(s) ------------------------------------------------------------------------------- *** NO INACTIVE CONNECTION ORIENTED ROUTER RESOURCEs PRESENT *** --------------------------- Inactive IP Resource(s) --------------------------- Type Resource(s) ------------------------------------------------------------------------------- *** NO INACTIVE IP RESOURCEs PRESENT *** --------------- Inactive PPP over Ethernet Resource(s) ------------------------- Type Resource(s) ------------------------------------------------------------------------------- *** NO INACTIVE PPPoE RESOURCEs PRESENT *** -------------------------- Inactive CTI Resource(s) --------------------------- Type Resource(s) ------------------------------------------------------------------------------- *** NO INACTIVE CTI RESOURCEs PRESENT *** ---------------------- Inactive Frame Relay Resource(s) ----------------------- Type Resource(s) ------------------------------------------------------------------------------- *** NO INACTIVE FRAME RELAY RESOURCEs PRESENT *** ----------------------- Inactive Pv and Ple Resource(s) ---------------------- Type Resource(s) ------------------------------------------------------------------------------- *** NO INACTIVE PV or PLE RESOURCEs PRESENT *** ------------------- Inactive Physical Communication Resource(s) --------------- Type Resource(s) ------------------------------------------------------------------------------- *** NO INACTIVE PHYSICAL RESOURCEs PRESENT ***
These commands set inactive the specified card(s) or resource(s).
[12:45:39] ABILIS_CPX:s inact ?CTIP: CTI port identifier [1..600] DEV: HW device identifier 'type-n', where 'n' can be [1..255] RES: Resource identifier 'type-n', where 'n' can be [1..999]
| Warning |
|---|---|
Deactivating a board or a port does not mean to make it not run, if it was running after the system start. Deactivation makes not possible to show card's/resource's parameters and to modify them. To make a card/port not running, it is needed to save the configuration (use the command save conf ) and restart the system (use the command warm start ). |
This command shows all the currently running resources and cards. The running resources and cards are the ones which are configured and active when at the system start.
A resource/card is still running even if it has been deactivated through the command s inact.
[11:38:04] ABILIS_CPX:d run+------------+-----+-----+-----+-----------------------------------------------+ | Resource | Act | UP | Alm | Description | +------------+-----+-----+-----+-----------------------------------------------+ | Async-1 | Yes | Yes | Off | | | Eth-1 | Yes | No | Off | | | Eth-2 | Yes | Yes | Off | | | Eth-3 | Yes | No | Off | | | Gps-1 | Yes | No | Off | | | Cp | Yes | Yes | Off | Control_Port | | Snmp | Yes | Yes | Off | Simple_Network_Management_Protocol | | Sntp | Yes | Yes | Off | Simple_Network_Time_Protocol | | Acnt | Yes | Yes | Off | Accounting_Service | | Trfa | Yes | Yes | Off | Traffic_Analyzer | | SysLog | Yes | Yes | Off | System_Log_protocol | | Opc | Yes | Yes | Off | Operator_Panel_Collector | | GpioPc | Yes | Yes | Off | General_Purpose_I/O_Panel_Collector | | Alarm | Yes | Yes | Off | Alarms_manager | | Script | Yes | Yes | Off | Lua_scripting_service | | X25-999 | Yes | Yes | Off | Resource_for_remote_maintenance | | Pad-1 | Yes | No | Off | | | Xtp-1 | Yes | Yes | Off | | | CtiSLink | Yes | Yes | Off | HDLC_Over_ISDN_B-Channel | | CtiSys | Yes | Yes | Off | CTI_System_general_properties | | CtiIax | Yes | Yes | Off | Inter-Asterisk_eXchange_Version_2 | | CtiDisa | Yes | Yes | Off | Direct_Inward_System_Access | | CtiSip | Yes | Yes | Off | Session_Initiation_Protocol | | CtiSms | Yes | Yes | Off | Short_Message_Service | | CtiAs | Yes | Yes | Off | CTI_Advanced_Services_entry_point | | CtiVm | Yes | Yes | Off | CTI_Voice_Mail_service | | CtiVr | Yes | Yes | Off | CTI_VR_service | | CtiMix | Yes | No | Off | CTI_Voice_Mixer_service | | CtiVo | Yes | Yes | Off | CTI_Virtual_Office | | Iprtr | Yes | Yes | Off | IP_Router_general_properties | | Tcp | Yes | Yes | Off | Transmission_Control_Protocol | | Udp | Yes | Yes | Off | User_Datagram_Protocol | | Telnet | Yes | Yes | Off | Telnet_Server_and_Client_entities | | Dns | Yes | Yes | Off | Domain_Name_System | | Http | Yes | Yes | Off | HyperText_Transfer_Protocol | | Nat | Yes | Yes | Off | Network_Address_Translator | | Ssh | Yes | Yes | Off | Secure_Shell_Protocol_2 | | Ospf | Yes | No | Off | Open_Shortest_Path_First_Routing_Protocol | | Dhcp | Yes | Yes | Off | Dynamic_Host_Configuration_Protocol | | Ftp | Yes | Yes | Off | File_Transfer_Protocol_Server | | IpSec | Yes | Yes | Off | IP_Security_Protocol | | Ike | Yes | Yes | Off | Internet_Keys_Exchange_Protocol | | Smtp | Yes | Yes | Off | Simple_Mail_Transfer_Protocol | | Vrrp | Yes | Yes | Off | Virtual_Router_Redundancy_Protocol | | DhcpC | Yes | Yes | Off | Dynamic_Host_Configuration_Protocol_Client | | DDns | Yes | Yes | Off | Dynamic_DNS_Protocol_Client | | Tftp | Yes | No | Off | Trivial_File_Transfer_protocol | | IpSh | Yes | Yes | Off | IP_Shaping_service | | Ldap | Yes | Yes | Off | Lightweight_Directory_Access_protocol | | Pv-1 | Yes | No | Off | | | NPv | Yes | Yes | Off | | | PoeAc-1 | Yes | No | Off | | | Ip-1 | Yes | No | Off | LAN | | Ip-2 | Yes | Yes | Off | WAN | | Ip-3 | Yes | No | Off | FREE | | Ip-6 | Yes | Yes | Off | VPN1 | | Ip-7 | Yes | Yes | Off | VPN2 | | Ip-8 | Yes | Yes | Off | To_AAD | | Ssl | Yes | Yes | Off | Secure_Socket_Layer | | Mf | Yes | Yes | Off | Abilis_Multi_Function_Interface | | UPnPS | Yes | Yes | Off | Universal_Plug_and_Play_Server | | MfIo | Yes | Yes | Off | Abilis_Multi_Function_IO_Interface | | MfTemp | Yes | Yes | Off | Abilis_Multi_Function_Temperature_device | | SysCtl | Yes | Yes | Off | Abilis_System_Control_device | | Vs | Yes | No | Off | Video_Surveillance | | Ups | Yes | No | Off | Uninterruptable_Power_Supply_device | +------------+-----+-----+-----+-----------------------------------------------+ Running CTI ports: +------+----------+-----+-----+-----+-----------------------------------------+ | CTIP | Card | Act | UP | Alm | Description | +------+----------+-----+-----+-----+-----------------------------------------+ | 31 | BSE-1 | Yes | No | Off | to_PBX | | 32 | BSE-1 | Yes | No | Off | | | 33 | BSE-1 | Yes | No | Off | to_ISDN_line | | 34 | BSE-1 | Yes | No | Off | | | 101 | BSE-1 | Yes | Yes | Off | phone_1 | | 102 | BSE-1 | Yes | Yes | Off | | | 103 | BSE-1 | Yes | No | Off | ddd | | 104 | BSE-1 | Yes | No | Off | | | 105 | BSE-1 | Yes | No | Off | | | 106 | BSE-1 | Yes | No | Off | | | 107 | BSE-1 | Yes | No | Off | | | 108 | BSE-1 | Yes | No | Off | | | 109 | BSE-1 | Yes | No | Off | | | 110 | BSE-1 | Yes | No | Off | | | 111 | BSE-1 | Yes | No | Off | | | 112 | BSE-1 | Yes | No | Off | | | 113 | BSE-1 | Yes | No | Off | | | 114 | BSE-1 | Yes | No | Off | | | 115 | BSE-1 | Yes | No | Off | | | 116 | BSE-1 | Yes | No | Off | | | 117 | BSE-1 | Yes | No | Off | | | 118 | BSE-1 | Yes | No | Off | | | 119 | BSE-1 | Yes | No | Off | | | 120 | BSE-1 | Yes | No | Off | | | 121 | BSE-1 | Yes | No | Off | | | 122 | BSE-1 | Yes | No | Off | | | 123 | BSE-1 | Yes | No | Off | | | 124 | BSE-1 | Yes | No | Off | | | 125 | BSE-1 | Yes | No | Off | | | 126 | BSE-1 | Yes | No | Off | | | 127 | BSE-1 | Yes | No | Off | | | 128 | BSE-1 | Yes | No | Off | | | 129 | BSE-1 | Yes | No | Off | | | 130 | BSE-1 | Yes | No | Off | | | 131 | BSE-1 | Yes | No | Off | | | 132 | BSE-1 | Yes | No | Off | | | 133 | BSE-1 | Yes | No | Off | | | 134 | BSE-1 | Yes | No | Off | | | 149 | VPOTS-4 | Yes | Yes | Off | | | 150 | VPOTS-4 | Yes | Yes | Off | | | 151 | VPOTS-4 | Yes | Yes | Off | | | 152 | VPOTS-4 | Yes | Yes | Off | | | 153 | VPOTS-4 | Yes | Yes | Off | | | 154 | VPOTS-4 | Yes | Yes | Off | | | 155 | VPOTS-4 | Yes | Yes | Off | | | 156 | VPOTS-4 | Yes | Yes | Off | | | 157 | VPOTS-4 | Yes | Yes | Off | | | 158 | VPOTS-4 | Yes | Yes | Off | | | 501 | CELL32-1 | Yes | No | Off | | +------+----------+-----+-----+-----+-----------------------------------------+ Running hardware devices: +-----+--------------+-----+------+-----------+ | Ind | Device | Act | Type | Connected | +-----+--------------+-----+------+-----------+ | 1 | ASY-1 | Yes | ISA | - | | 2 | ETH-1 | Yes | PCI | - | | 3 | BSE-1 | Yes | PCI | - | | 4 | ETH-3 | Yes | PCI | - | | 5 | ETH-2 | Yes | PCI | - | | 6 | UPS-1 | Yes | USB | No | | 7 | CELLKEY-1 | Yes | USB | No | | 8 | CELL32-1 | Yes | PCI | - | | 9 | GPS-1 | Yes | USB | No | | 10 | VPOTS-4 | Yes | PCI | - | +-----+--------------+-----+------+-----------+
This command shows the real status of the connections among protocol resources and the physical link. Resources can be split into 7 groups:
System Resource(s)
Management Resource(s)
Connection Oriented Router Resource(s)
IP Resource(s)
CTI Resource(s)
Wireless to G.703 bridge
Unconnected Physical Resource(s)
Before showing the resources connections, the command automatically executes a validation of the current configuration. If the validation is successful, the command will be executed, otherwise it won't.
For more details on the configuration validation procedure see the section Section 5.12, “Configuration validating and saving”.
[11:38:04] ABILIS_CPX:d tree----------------------------- System Resource(s) ------------------------------ Gps-1 Ssl Mf UPnPS \---Tcp \---Udp MfIo MfTemp SysCtl Vs \---Tcp Ups --------------------------- Management Resource(s) ---------------------------- Cp Snmp \---Udp Sntp \---Udp Acnt \---Tcp Trfa SysLog \---Udp Opc \---Tcp GpioPc Alarm Script ------------------- Connection Oriented Router Resource(s) -------------------- X25-999 \---CtiSLink Pad-1 \---Async-1 Xtp-1 \---Tcp ------------------------------- IP Resource(s) -------------------------------- Iprtr \---Ip-1 \---Eth-1 \---Ip-2 \---Eth-2 \---Ip-3 \---Eth-3 \---Ip-6 \---Udp \---Ip-7 \---Udp \---Ip-8 \---Udp Tcp Udp Telnet \---Tcp Dns \---Udp Http \---Tcp Nat Ssh \---Tcp Ospf Dhcp \---Udp Ftp \---Tcp IpSec Ike \---Udp Smtp \---Tcp Vrrp DhcpC \---Udp DDns \---Tcp Tftp \---Udp IpSh Ldap \---Tcp -------------------- PPPoE Access Concentrator Resource(s) -------------------- PoeAc-1 ------------------------------- CTI Resource(s) ------------------------------- CtiSLink CtiSys \---CTIP:31..38, 101..140 [BSE-1] \---CTIP:501..532 [CELL32-1] \---CTIP:149..164 [VPOTS-4] \---(CTIL: 1) NPv (NPVL: 1) \---Udp \---(CTIL: 2) NPv (NPVL: 2) \---Udp CtiIax \---Udp CtiDisa CtiSip \---Tcp \---Udp CtiSms CtiAs CtiVm \---CtiAs CtiVr \---CtiAs CtiMix \---CtiAs CtiVo \---CtiAs \---Udp --------------- Unconnected Fr, PoeCli, Pv and Ple Resource(s) ---------------- Pv-1 \---Udp --------------- Unconnected Physical Communication Resource(s) ---------------- *** NO ACTIVE UNCONNECTED PHYSICAL RESOURCEs PRESENT ***
The command alarm view shows a list of the resources in error conditions that have generated the alarm.
[11:38:04] ABILIS_CPX:alarm viewRES:Pv-6 - PV over IP (Abilis tunnel) with Abilis Back-up (IP-BCK) ----------- To_Abilis_6 - Link ----------------------------------------------------------------- +--------+--- Global ----+------- P-Link -------+------- S-Link -------+ | STATE: | DOWN | DOWN1 | LINK-NOT-PRESENT | +--------+---------------+----------------------+----------------------+ RES:Pv-12 - PV over IP (Abilis tunnel) (IP) ----------------------------------- To_Abilis_12 - Link ----------------------------------------------------------------- +--------+--- Global ----+------- P-Link -------+------- S-Link -------+ | STATE: | DOWN | DOWN1 | LINK-NOT-PRESENT | +--------+---------------+----------------------+----------------------+
If there are no alarmed resources when the command is executed, the message “NO ALARMED RESOURCES” will be shown.
Resources alarms are detected by a proper procedure, which is
executed every 30 seconds and is activated setting the
A option in the LLOG parameter. If
the L option is also set in the
LLOG parameter, on alarm detection, acoustic signal
and message on the LCD display are generated.
The command alarm reset activates a reset procedure of error conditions that generated the alarm.
[11:38:04] ABILIS_CPX:alarm resetCOMMAND EXECUTED
The command call res: opens a connection on the specified resources. The resource value must be in the interval [0 - 999] and has to correspond to a resource that is active and running.
The command can work only on MLM and PPP resource types, otherwise the message “COMMAND NOT ALLOWED FOR 'RES:type-nnn” is generated.
[11:38:04] ABILIS_CPX:call res:pv-1COMMAND EXECUTED
Open connection must be closed using the disc res: command.
If the command has been already executed on the specified resource, while the disc res: one was not, then the message “CONNECTION ALREADY OPENED” will be displayed. The command will work only on present, active and running resources; otherwise the error message “RESOURCE NOT PRESENT OR NOT RUNNING” will be displayed.
[11:38:04] ABILIS_CPX:disc res:pv-1COMMAND EXECUTED
| |  | |
| 5.6. Resources or Ports |  | 5.8. General and system information |