| 5.13. System management | ||
|---|---|---|
 | Chapter 5. Command language |  |
| 5.13. System management | ||
|---|---|---|
| | Chapter 5. Command language | |
In this section the most frequently used commands about system management are shown.
With conf and conflog commands it is possible to copy, restore or save configuration and Log files. Below there's the commands syntax:
[15:43:26] ABILIS_CPX:conflog ?BACKUP Copy configuration and log files to removable disk RESTORE Load configuration files from removable disk[15:43:26] ABILIS_CPX:conf ?BACKUP Copy configuration to removable disk GET Sends the configuration in memory to a remote site INFO Display/set configuration notes PUT Receives configuration from a remote site RELOAD Reload the configuration from a file RESTORE Alias of the CONFLOG RESTORE command SAVE Alias of the SAVE CONF command(s) VALIDATE Alias of the VALIDATE command
![[Tip]](../images/tip.png) | Tip |
|---|---|
Interesting chapter: Section 67.8, “How to copy files using a removable drive”. |
With file commands it is possible to copy/delete a file or to transfer a file from and to Abilis CF/HD. Abilis supports XMODEM, XMODEM-1K, ZMODEM protocols for file transfer, from and to Abilis (use a terminal emulator which is compatible with the protocols mentioned above, to transfer files or system releases).
[15:43:26] ABILIS_CPX:file ?COPY Make a copy of a file DELETE Delete a file GET Send a file using XMODEM or XMODEM-1K or ZMODEM PUT Receive a file using XMODEM or XMODEM-1K or ZMODEM
With sys commands it is possible to manage Abilis CPX system software.
The following command displays the syntax:
[15:43:26] ABILIS_CPX:sys ?COMPACT Directory re-compacting operation COMPACTR Directory re-compacting operation, recursive COPY Make a copy of a file CREATE Create a directory DELETE Delete operations DIR List operations DISK Disk and Volume management DISPLAY Display operations GET Send a file using XMODEM or XMODEM-1K or ZMODEM PUT Receive a file using XMODEM or XMODEM-1K or ZMODEM SET Set operations UPDATE Receive a package or a new disk image and update the system
This command copies configuration and Log files
(DRIVERS.CFG, DRIVERS.BCK,
DHCP.BND, CPX.LOG,
CPX.DBG and CPX.XCP) of the
current version or of the specified version to a removable disk.
The <version> string must correspond to an existing version directory in the form 'X.Y.Z' or 'X-Y-Z' or 'Y.Z' or 'Y-Z' or 'Y', where X, Y and Z are decimal digit [0 - 9] (E.g.: 8-0-2).
With the command conf backup it is possible to copy only configurations file.
[15:43:26] ABILIS_CPX:conflog backupYOU ARE GOING TO BACKUP CONFIGURATION AND LOG FILES OF CURRENT VERSION TO 'D:\__Abilis_Cpx_Backup_And_Restore__'. PROCEED (N/Y)?y PROCEEDING WITH CONFIGURATION AND LOG FILES BACKUP... FILE 'DRIVERS.CFG'... SUCCESSFULLY COPIED. FILE 'DRIVERS.BCK'... SUCCESSFULLY COPIED. FILE 'CPX.LOG'... SUCCESSFULLY COPIED. FILE 'CPX.DBG'... SUCCESSFULLY COPIED. FILE 'CPX.XCP'... SUCCESSFULLY COPIED. FILE 'C:\APP\DHCP\DHCP.BND'... SUCCESSFULLY COPIED. COMMAND COMPLETED
| Tip |
|---|---|
Interesting chapter: Section 67.8, “How to copy files using a removable drive”. |
These commands copy configuration files
(DRIVERS.CFG and DRIVERS.BCK)
from a removable disk to the current version or to the specified version
directory.
The <version> string must correspond to an existing version directory in the form 'X.Y.Z' or 'X-Y-Z' or 'Y.Z' or 'Y-Z' or 'Y', where X, Y and Z are decimal digit [0 - 9] (E.g.: 8-0-2).
[15:43:26] ABILIS_CPX:conflog restoreYOU ARE GOING TO RESTORE CONFIGURATION FILES OF CURRENT VERSION FROM 'D:\__Abilis_Cpx_Backup_And_Restore__'. PROCEED (N/Y)?y PROCEEDING WITH CONFIGURATION FILES RESTORE... FILE 'D:\__Abilis_Cpx_Backup_And_Restore__\DRIVERS.CFG'... SUCCESSFULLY COPIED. FILE 'D:\__Abilis_Cpx_Backup_And_Restore__\DRIVERS.BCK'... SUCCESSFULLY COPIED. COMMAND COMPLETED
| Tip |
|---|---|
Interesting chapter: Section 67.8, “How to copy files using a removable drive”. |
This command makes a copy of the “srcname” file into the specified “dtsname” path/file. The following command displays the syntax.
[15:43:26] ABILIS_CPX:file copy ?FILE COPY srcname dstname Make a copy of a file SYS COPY srcname dstname Make a copy of a file srcname Path or name of the source file to be copied. <Mandatory> When the file path is omitted the running version directory path is used. Spaces are allowed. Strings holding spaces must be written between quotation marks. (E.g.: "C:\APP\MY USERS\aaa.log") dstname Path or name of the target file. <Mandatory> When the file path is omitted the running version directory path is used. Spaces are allowed. Strings holding spaces must be written between quotation marks. (E.g.: A: or C:\4-3-1\ or Fdsp.bin or C:\4-3-2\drivers.cfg)
The “srcname” must be a file name. If the path is omitted the source file is assumed to be located in the current running version directory.
The “dstname” can either a path or a file name. If the path is omitted the destination directory is assumed to be the current running version directory.
Wildcards characters are not accepted either in the source file name nor in the destination name.
File copies to root directory are not allowed.
Log files (Cpx.log,
Cpx.dbg and Cpx.xcp) and
Cpx.rtb file cannot be overwritten.
This command deletes the specified file. The following command displays the syntax.
[15:43:26] ABILIS_CPX:file delete ?FILE DELETE filename Delete a file SYS DELETE FILE filename Delete a file filename Path or name of the file to be deleted. <Mandatory> When the file path is omitted the running version directory path is used. Spaces are allowed. Strings holding spaces must be written between quotation marks. (E.g.: "C:\APP\MY DATA\aaa bbb.dat")
The “filename” must be a file name. If the path is omitted the source file is assumed to be located into the current running version directory.
Wildcards characters are not accepted in the file name.
Files that are located into root directory cannot be deleted.
File copies to root directory are not allowed.
Configuration files, log files (Cpx.log,
Cpx.dbg and Cpx.xcp) and any
other system file cannot be deleted from the current running version
directory.
This command allows to download files from the Abilis CPX. The following command displays the syntax.
[15:43:26] ABILIS_CPX:file get ?FILE GET [X] fname [<ver>][1K] Send a file using XMODEM or XMODEM-1K FILE GET Z fname [<ver>] Send a file using ZMODEM SYS GET [X] fname [<ver>][1K] Send a file using XMODEM or XMODEM-1K SYS GET Z fname [<ver>] Send a file using ZMODEM X or Z Select the X or Z MODEM protocol (by default XMODEM is used) XMODEM transfer is allowed only on files relative to the running version directory or to the specified '<ver>' version directory. ZMODEM transfer is allowed on any files. For file not relative either to the running version directory or to the '<ver>' version directory, the absolute file name is required i.e. including the full path. fname Name of the file to be sent <Mandatory> Spaces are allowed. Strings holding spaces must be written between quotation marks. (E.g.: "C:\APP\MY DATA\aaa bbb.dat") <ver> String corresponding to a version directory in <Optional> the form [x.y.z or x-y-z or y.z or y-z or y]. (E.g.: 5.3.1 or 6-1-0 or 2189). Accepted only if 'fname' does not contain the full path. 1K Select XMODEM-1K transfer protocol <Optional>
The transfer procedure signals its availability to send the file by the message:
READY TO SEND FILE...
When the transfer is completed the following message is shown:
FILE TRANSFER ENDED, PRESS <ENTER> TO CONTINUE...
After pressing the Enter button, if the transfer was successful, the following message will be shown.
FILE TRANSFER SUCCESFULLY COMPLETED
This command allows to upload files to the Abilis CPX. The following command displays the sintax:
[15:43:28] ABILIS_CPX:file put ?FILE PUT [X] fname [<ver>] Receive a file using XMODEM or XMODEM-1K FILE PUT Z fname [<ver>] Receive a file using ZMODEM SYS PUT [X] fname [<ver>] Receive a file using XMODEM or XMODEM-1K SYS PUT Z fname [<ver>] Receive a file using ZMODEM X or Z Select the X or Z MODEM protocol (by default XMODEM is used) XMODEM transfer is allowed only on files relative to the running version directory or to the specified '<ver>' version directory and only DRIVERS.CFG, DRIVERS.BCK, DHCP.BND, IKE.CNS files and mandatory fw files and optional USB devices and cards fw files are allowed. ZMODEM transfer is allowed on any files. For file not relative either to the running version directory or to the '<ver>' version directory, the absolute file name is required i.e. including the full path. fname Name of the file to be received <Mandatory> Spaces are allowed. Strings holding spaces must be written between quotation marks. (E.g.: "C:\APP\MY DATA\aaa bbb.dat") <ver> String corresponding to a version directory in <Optional> the form [x.y.z or x-y-z or y.z or y-z or y]. (E.g.: 5.3.1 or 6-1-0 or 2189). Accepted only if 'fname' does not contain the full path.
The transfer procedure signals its availability to receive the file by the message:
READY TO RECEIVE FILE...
When the transfer is completed the following message is shown:
FILE TRANSFER ENDED, PRESS <ENTER> TO CONTINUE...
After pressing the Enter button, if the transfer was successful, the following message will be shown.
FILE TRANSFER SUCCESFULLY COMPLETED
Once the file is received, it is submitted to a congruence control for checking its content validity. The User is informed through the message:
RECEIVED FILE 'namefile' CHECK IN PROGRESS...
If the file content is not correct:
CHECK FAILED: FILE 'namefile' DELETED
If file content and version are correct:
CHECK PASSED
This command compacts the specified directory. It's useful when a lot of files have been deleted or renamed in a directory to reduce its size.
[14:13:06] ABILIS_CPX:sys compact c:
COMPACTING DIRECTORY 'c:' ...
COMMAND EXECUTED, RECOVERED 2 SHORT DIRECTORY ENTRIES![[Note]](../images/note.png) | Note |
|---|---|
This command copies all used directory entries to the start of the directory and zeros out all slack space. If the slack space is larger than one cluster, the slack space is freed, reducing the allocated size of a directory. |
This command compacts specified directory and sub-directories. It's useful when a lot of files have been deleted or renamed in a directory and sub-directories to reduce their size.
[14:14:43] ABILIS_CPX:sys compactr c:
THIS OPERATION MAY TAKE FEW MINUTES AND LOCKS ACCESS TO DISK c:
PROCEED ANYWAY (N/Y)?y
COMPACTING DIRECTORY 'c:' AND ALL OF ITS SUBDIRECTORIES...
COMMAND EXECUTED, RECOVERED 0 SHORT DIRECTORY ENTRIES | Note |
|---|---|
This command copies all used directory entries to the start of the directory and zeros out all slack space. If the slack space is larger than one cluster, the slack space is freed, reducing the allocated size of a directory. |
This command deletes the specified package file. Use sys delete package <name of package> where <name of package> must be the name of a package file located in 'C:\pkg' or an absolute package file name (the full path is required).
[14:21:22] ABILIS_CPX:sys delete package test.pkg
YOU ARE GOING TO DELETE THE 'C:\PKG\TEST.PKG' PACKAGE FILE.
PROCEED (N/Y)?y
PACKAGE 'C:\PKG\TEST.PKG' DELETEDIt deletes the specified version directory.
[14:23:25] ABILIS_CPX:sys dir c:\Directory listing of c:\ PKG <DIR> 18/02/2015 18:02:46 LOG <DIR> 18/02/2015 18:02:46 USR <DIR> 18/02/2015 18:02:46 7-9-14 <DIR> 07/04/2015 13:08:18 8-0-2 <DIR> 16/04/2015 11:40:50 LICENCE <DIR> 18/02/2015 18:52:12 7-9-10 <DIR> 18/02/2015 18:52:12 APP <DIR> 18/02/2015 18:52:12 BM.CFG 108 16/04/2015 11:44:46 autorun.inf 14229 18/04/2014 14:03:52 BM.LOG 4096 16/04/2015 11:44:46 TIMECFG.DAT 30 22/04/2015 11:45:42 CPXRUN.CFG 80 16/04/2015 11:45:02 BOOTSECT.RTT 512 18/02/2015 18:51:58 bm.RTA 107008 18/02/2015 18:51:58 8 directory, 7 file (126,063 byte). Total 121 MiB, Used 36 MiB, Free 84 MiB. [14:23:42] ABILIS_CPX:sys delete version 7-9-10YOU ARE GOING TO DELETE THE 'C:\7-9-10' VERSION DIRECTORY. PROCEED (N/Y)?y VERSION 'C:\7-9-10' DELETED [14:24:23] ABILIS_CPX:sys dir c:\Directory listing of c:\ PKG <DIR> 18/02/2015 18:02:46 LOG <DIR> 18/02/2015 18:02:46 USR <DIR> 18/02/2015 18:02:46 7-9-14 <DIR> 07/04/2015 13:08:18 8-0-2 <DIR> 16/04/2015 11:40:50 LICENCE <DIR> 18/02/2015 18:52:12 APP <DIR> 18/02/2015 18:52:12 BM.CFG 108 16/04/2015 11:44:46 autorun.inf 14229 18/04/2014 14:03:52 BM.LOG 4096 16/04/2015 11:44:46 TIMECFG.DAT 30 22/04/2015 11:45:42 CPXRUN.CFG 80 16/04/2015 11:45:02 BOOTSECT.RTT 512 18/02/2015 18:51:58 bm.RTA 107008 18/02/2015 18:51:58 7 directory, 7 file (126,063 byte). Total 121 MiB, Used 24 MiB, Free 96 MiB.
This command makes possible the system software update in two ways:
By receiving from a remote source the package file holding the updated software and installing it on the CF/HD in a proper version directory.
The transfer procedure signals its availability to receive the package file by the following messages:
[18:01:32] ABILIS_CPX:sys updateSYSTEM UPDATE PROCEDURE PLEASE UPLOAD THE PACKAGE FILE. READY TO RECEIVE PACKAGE...
When the transfer is completed the following message is shown:
PACKAGE TRANSFER ENDED, PRESS <ENTER> TO CONTINUE...
Once the Enter button is pressed by the User, if the transfer was successful, an informative message will be shown and the system will start the received package integrity check procedure. If the received package passes the validation procedure, the software extraction and installation takes place.
PACKAGE TRANSFER SUCCESSFULLY COMPLETED RECEIVED PACKAGE CHECK and EXTRACTION IN PROGRESS... CHECK PASSED, EXTRACTION DONE. VERSION '8-0-2' SUCCESSFULLY INSTALLED.
By a package file already present in the 'C:\PKG' directory, installing it on the HD/CF in a proper version directory.
In this case the package file name specification is required by the User on the command line: sys update <package>. The <package> string must be the name of a package file located in 'C:\PKG' or an absolute package file name (i.e. the full path is required). If the specified package file is not present, the message “FILE 'C:\PKG\<package> NOT FOUND” will be shown.
The procedure starts with a package integrity check. If the package passes the validation phase, the software extraction and installation takes place.
[18:01:32] ABILIS_CPX:sys update 8-0-2 PACKAGE 'C:\PKG\8-0-2.PKG' CHECK and EXTRACTION IN PROGRESS (8-0-2)... CHECK PASSED, EXTRACTION DONE. VERSION '8-0-2' SUCCESSFULLY INSTALLED.
If the package verifications and extraction is successful, the package file is always deleted.
If the procedure fails for any reason, the package deletion takes place only after the User confirmation.
The list of currently available package files can be displayed by the command sys display packages; while a package file can be deleted by the command sys delete package.
Once a new software version is installed on the system, it can be set to be loaded at next system startup by the command sys set boot version. The list of currently available versions can be displayed by the command sys display versions. Old versions, not longer useful, can be deleted by the command sys delete version.
| Tip |
|---|---|
Interesting chapter: Section 67.4, “How to remotely upgrade the Abilis firmware”. |
It shows the directory listing of the specified path.
[14:26:13] ABILIS_CPX:sys dir c:\
Directory listing of c:\
PKG <DIR> 18/02/2015 18:02:46
LOG <DIR> 18/02/2015 18:02:46
USR <DIR> 18/02/2015 18:02:46
7-9-14 <DIR> 07/04/2015 13:08:18
8-0-2 <DIR> 16/04/2015 11:40:50
LICENCE <DIR> 18/02/2015 18:52:12
APP <DIR> 18/02/2015 18:52:12
BM.CFG 108 16/04/2015 11:44:46
autorun.inf 14229 18/04/2014 14:03:52
BM.LOG 4096 16/04/2015 11:44:46
TIMECFG.DAT 30 22/04/2015 11:45:42
CPXRUN.CFG 80 16/04/2015 11:45:02
BOOTSECT.RTT 512 18/02/2015 18:51:58
bm.RTA 107008 18/02/2015 18:51:58
7 directory, 7 file (126,063 byte).
Total 121 MiB, Used 24 MiB, Free 96 MiB.It displays logical drive(s) information.
[14:43:07] ABILIS_CPX:sys disk info
Logical drive(s) information:
Drv Disk Label FAT Free space Used space Total space
Interface Sectors per block Cluster size Bootable
-------------------------------------------------------------------------------
C: HD-0 16 72 MB 52 MB 124 MB
IDE-PIO-32 1 2,048 Bytes YES
-------------------------------------------------------------------------------
D: HD-4 USB_DRIVE 32 976 MB 2 KB 976 MB
USB 2,048 Bytes YES
-------------------------------------------------------------------------------It checks the disk drive integrity. Use sys disk chk ? to display options.
[14:27:57] ABILIS_CPX:sys disk chk
THIS OPERATION MAY TAKE FEW MINUTES AND LOCKS ACCESS TO ALL DISKS.
PROCEED ANYWAY (N/Y)?y
DISK 'C:' INTEGRITY CHECK IN PROGRESS...
DISK 'C:' INTEGRITY CHECK SUCCESSFULLY COMPLETED
NO ERRORs WERE FOUNDIt formats the specified drive. Note that system drive c: can't be formatted.
[14:35:22] ABILIS_CPX:sys disk format d:
DO YOU REALLY WANT TO FORMAT DRIVE 'D:' (N/Y)?y
THIS OPERATION WILL DELETE ALL EXISTING DATA FROM DRIVE 'D:'.
PROCEED ANYWAY (N/Y)?y
DRIVE 'D:' FORMAT IN PROGRESS... DONE.
ENTER VOLUME LABEL (MAX. 11 CHARACTERs, PRESS <ENTER> FOR NO LABEL): udisk
DRIVE 'D: FORMATTED:
FILE SYSTEM IS FAT-32, Size: 976 MB
Bytes per sector: 512, Sectors per cluster: 4, Clusters: 500054
Serial N. 3E35-746F, Label: UDISK
COMMAND COMPLETEDIt set the label of the selected drive or remove any existing label.
[14:41:40] ABILIS_CPX:sys disk label d:ENTER VOLUME LABEL (MAX. 11 CHARACTERs, PRESS <ENTER> FOR NO LABEL): usb_drive COMMAND EXECUTED [14:41:51] ABILIS_CPX:sys disk infoLogical drive(s) information: Drv Disk Label FAT Free space Used space Total space Interface Sectors per block Cluster size Bootable ------------------------------------------------------------------------------- C: HD-0 16 72 MB 52 MB 124 MB IDE-PIO-32 1 2,048 Bytes YES ------------------------------------------------------------------------------- D: HD-4 USB_DRIVE 32 976 MB 2 KB 976 MB USB 2,048 Bytes YES -------------------------------------------------------------------------------
It displays Master Boot Record of a disk.
[14:45:58] ABILIS_CPX:sys disk mbr dump hd:0
Address | Hexadecimal values | Ascii values
---------+-------------------------------------------------+-----------------
00000000 | FA BE 00 7C BF 00 7A B9 00 01 FC 0E 1F 0E 07 F3| ...|..z.........
00000010 | A5 EA 16 7A 00 00 BB BE 7B 33 C9 80 3F 80 75 06| ...z....{3..?.u.
00000020 | FE C5 8B F3 EB 07 80 3F 00 75 02 FE C1 83 C3 10| .......?.u......
00000030 | 81 FB FE 7B 72 E5 83 F9 04 74 0B 81 F9 03 01 74| ...{r....t.....t
00000040 | 0A BB A6 7A EB 2C BB 87 7A EB 27 8B 4C 02 8B 14| ...z.,..z.'.L...
00000050 | B8 01 02 BB 00 7C CD 13 73 05 BB BE 7A EB 13 2E| .....|..s...z...
00000060 | A1 FE 7D 3D 55 AA 74 05 BB BE 7A EB 05 EA 00 7C| ..}=U.t...z....|
00000070 | 00 00 2E 8A 07 3C 00 74 0C 53 BB 07 00 B4 0E CD| .....<.t.S......
00000080 | 10 5B 43 EB ED EB FE 4E 6F 20 62 6F 6F 74 61 62| .[C....No bootab
00000090 | 6C 65 20 70 61 72 74 69 74 69 6F 6E 20 69 6E 20| le partition in
000000A0 | 74 61 62 6C 65 00 49 6E 76 61 6C 69 64 20 50 61| table.Invalid Pa
000000B0 | 72 74 69 74 69 6F 6E 20 74 61 62 6C 65 00 49 6E| rtition table.In
000000C0 | 76 61 6C 69 64 20 6F 72 20 64 61 6D 61 67 65 64| valid or damaged
000000D0 | 20 42 6F 6F 74 61 62 6C 65 20 70 61 72 74 69 74| Bootable partit
000000E0 | 69 6F 6E 00 53 79 73 74 65 6D 53 6F 66 74 20 42| ion.SystemSoft B
000000F0 | 6F 6F 74 20 50 61 72 74 69 74 69 6F 6E 20 53 65| oot Partition Se
00000100 | 63 74 6F 72 00 00 00 00 00 00 00 00 00 00 00 00| ctor............
00000110 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00| ................
00000120 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00| ................
00000130 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00| ................
00000140 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00| ................
00000150 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00| ................
00000160 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00| ................
00000170 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00| ................
00000180 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00| ................
00000190 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00| ................
000001A0 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00| ................
000001B0 | 00 00 00 00 00 00 00 00 14 9B 61 92 00 00 80 01| ..........a.....
000001C0 | 01 00 06 07 E0 E8 20 00 00 00 E0 E8 03 00 00 00| ...... .........
000001D0 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00| ................
000001E0 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00| ................
000001F0 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 55 AA| ..............U.It displays partition(s) information.
[14:47:41] ABILIS_CPX:sys disk partition info
Available Hard Disk(s) information:
HD Size Partition Drive Label FAT Size Bootable
-------------------------------------------------------------------------------
0 125 MB 1 C: 16 124 MB YES
4 984 MB 1 D: USB_DRIVE 32 976 MB YESIt adds partition(s) to the specified disk.
[14:47:41] ABILIS_CPX:sys disk partition infoAvailable Hard Disk(s) information: HD Size Partition Drive Label FAT Size Bootable ------------------------------------------------------------------------------- 0 125 MB 1 C: 16 124 MB YES 4 984 MB 1 D: USB_DRIVE 32 976 MB YES [14:48:05] ABILIS_CPX:sys disk partition add ?HD: Hard disk index [0..31] [14:48:33] ABILIS_CPX:sys disk partition add hd:4Hard Disk '4' information: HD Size Partition Drive Label FAT Size Bootable ------------------------------------------------------------------------------- 4 984 MB 1 D: USB_DRIVE 32 976 MB YES HARD DISK '4' ALREADY HOLDS 1 PARTITIONs. DO YOU WANT TO ADD A NEW PARTITION (N/Y)?y THIS OPERATION WILL SPLIT PARTITION 1 ('D:') INTO TWO PARTITIONs. ALL DATA ON 1 ('D:') PARTITION WILL BE LOST. PROCEED (N/Y)?yPLEASE ENTER THE SIZE YOU WANT TO RESERVE FOR PARTITION 1 ('D:'), THE REMAINING SPACE WILL BE ASSIGNED TO THE NEW PARTITION, IN MBytes (0 TO EXIT):400THE SIZE OF PARTITION 1 ('D:') WILL BE ABOUT 400 MB THE SIZE OF THE NEW PARTITION WILL BE ABOUT 576 MB PROCEED (N/Y)?yHARD DISK PARTITIONING OPERATIONS REQUIRE THAT NO FILES ARE OPENED. IF SOME FILES ARE CURRENTLY OPENED IN THE SYSTEM, THE COMMAND WILL WAIT UNTIL ALL FILES WILL BE CLOSED. PROCEED (N/Y)?yWAITING THAT ALL FILES GET CLOSED (TYPE CTRL+C + ENTER TO STOP)... DONE. NEW PARTITION CREATION IN PROGRESS... DONE. PARTITION 1 ('D:') SUCCESSFULLY SPLITTED ON HARD DISK '4' PARTITION 2 ('E:') SUCCESSFULLY CREATED ON HARD DISK '4' DRIVE 'D:' FORMAT IN PROGRESS... DONE. ENTER VOLUME LABEL (MAX. 11 CHARACTERs, PRESS <ENTER> FOR NO LABEL):usb_driveDRIVE 'D: FORMATTED: FILE SYSTEM IS FAT-32, Size: 976 MB Bytes per sector: 512, Sectors per cluster: 4, Clusters: 500054 Serial N. 3E35-7630, Label: USB_DRIVE
It resets all existing partition(s) for the specified disk.
[15:01:10] ABILIS_CPX:sys disk partition reset hd:4Hard Disk '4' information: HD Size Partition Drive Label FAT Size Bootable ------------------------------------------------------------------------------- 4 984 MB 1 D: PENDRIVE 32 976 MB YES DO YOU REALLY WANT TO DELETE ALL EXISTING PARTITIONs ON HARD DISK '4' (N/Y)?yTHIS OPERATION WILL DELETE ALL EXISTING PARTITIONs AND CREATE A SINGLE NEW PARTITION ON HARD DISK '4'. PROCEED (N/Y)?yHARD DISK PARTITIONING OPERATIONS REQUIRE THAT NO FILES ARE OPENED. IF SOME FILES ARE CURRENTLY OPENED IN THE SYSTEM, THE COMMAND WILL WAIT UNTIL ALL FILES WILL BE CLOSED. PROCEED (N/Y)?yWAITING THAT ALL FILES GET CLOSED (TYPE CTRL+C + ENTER TO STOP)... DONE. CREATING A SINGLE NEW PARTITION ON HARD DISK '4'... DONE. PARTITION 1 ('D:') SUCCESSFULLY CREATED ON HARD DISK '4' DRIVE 'D:' FORMAT IN PROGRESS... DONE. ENTER VOLUME LABEL (MAX. 11 CHARACTERs, PRESS <ENTER> FOR NO LABEL): drive1 DRIVE 'D: FORMATTED: FILE SYSTEM IS FAT-32, Size: 980 MB Bytes per sector: 512, Sectors per cluster: 4, Clusters: 501837 Serial N. 3E35-7851, Label: DRIVE1 COMMAND COMPLETED
This command allows to change Boot Manager configuration setting the version that must be loaded at next system startup.
The list of available versions can be displayed by sys display versions command; while the current/new Boot Manager configuration is displayed by sys display boot command.
[15:43:26] ABILIS_CPX:sys display bootAbilis CPX Boot Manager configuration: Previous version Current version Next Version to load ------------------------------------------------------------------------------ 7-9-14 8-0-0 8-0-0[15:43:26] ABILIS_CPX:sys set boot version 8-0-2BOOT MANAGER CONFIGURATION UPDATED: THE NEXT VERSION THAT WILL BE LOADED IS '8-0-2'. COMMAND EXECUTED [[15:43:26] ABILIS_CPX:sys display bootAbilis CPX Boot Manager configuration: Previous version Current version Next Version to load ------------------------------------------------------------------------------ 7-9-14 8-0-0 8-0-2
This command allows to show some information about Abilis boot. Every time Abilis CPX boots a log, showing the date and time, is generated.
[14:14:57] ABILIS_CPX:_d tCurrent Local Time : Wednesday 22/04/2015 12:19:20 (UTC+2.00) Local Time Zone : CET - Central Europe (Rome, Paris, Berlin, Pragu... Currently Observing : Daylight Savings Time (DST) Clock Reference : SNTP Clock Reference state : Working Clock last synchronized : 22/04/2015 at 11:45:42 Delta:-1 sec. [14:15:00] ABILIS_CPX:_warm start PROCEED WITH WARM START (N/Y)?y ... [14:16:37] ABILIS_CPX:_sys display boot logBoot Manager log file: ... ***** New run at 2015-04-16 11:44:46 +0200 ***** CPX Boot manager: v. 2034 - 04/10/2013 Setting current directory Loading configuration Loading CPX response file Accepting 'new' version Saving configuration Removing CPX response file Writing info to shared region Loading file: 8-0-2\CPX.RTB Starting loaded RTB file
This command immediately executes the system restart.
[11:38:04] ABILIS_CPX:warm start
If in the current session the configuration was modified but not saved, the command displays a warning message and queries the User for proceeding with configuration saving or not.
In case of affirmative answer, the save conf command is executed, the reset of the Abilis CPX is not executed and the Control Port prompt is shown.
[11:38:04] ABILIS_CPX:warm startTHE CURRENT CONFIGURATION WAS MODIFIED BUT NOT SAVED. PROCEED WITH 'SAVE CONF' COMMAND (N/Y/A)?yVALIDATION IN PROGRESS... VALIDATION SUCCESSFULLY EXECUTED SAVE EXECUTED
If a different version from the currently running one was set to be loaded at next system start up (sys set boot version), the command displays a warning message and queries the User for proceeding with system restart.
[11:38:04] ABILIS_CPX:warm startBOOT MANAGER CONFIGURATION WAS MODIFIED: THE NEXT VERSION THAT WILL BE LOADED IS '8-0-2', WHILE THE CURRENTLY RUNNING VERSION IS '8-0-0'. PROCEED WITH WARM START (N/Y)?y
The options of warm start command:
[11:38:04] ABILIS_CPX:warm start ?WARM START [opt] System warm start is executed Allowed options: -DELAY hh:mm The system will reboot after the specified delay, <Optional> where 'hh' [0..2400], 'mm' [0..59]. -NOCALL The system will reboot as soon as all CTI calls are <Optional> closed. -CLEAR Clear any scheduled system reboot. <Optional> -SHOW Show currently set system reboot delay or condition. <Optional> -F Force system warm start interrupting any operation <Optional> in progress (E.g. configuration saving, system updating, file uploading/downloading and so on).
| Note |
|---|---|
The -f option, force system warm start interrupting any operation that is in progress (e.g. configuration saving, system updating, file uploading/downloading and so on).
In case of affirmative answer, the reset of the Abilis CPX is executed, while in case of negative answer the Control Port prompt is shown. |
| |  | |
| 5.12. Configuration validating and saving |  | 5.14. Diagnostics and Statistics |