67.8. How to copy files using a removable drive
Prev Chapter 67. HowTo - Management Next

67.8. How to copy files using a removable drive

67.8.1. How to copy configuration and log files on an USB disk through the command-line interface

Insert an USB disk in one of the Abilis USB ports.

[Tip]Tip

Type the command sys disk info to verify that the USB device is correctly mounted.

[17:11:41] ABILIS_CPX:_sys disk info

Logical drive(s) information:

Drv Disk   Label       FAT     Free space      Used space      Total space
    Interface          Sectors per block       Cluster size    Bootable
-------------------------------------------------------------------------------
C:  HD-0               16      105 MB          13 MB           119 MB
    IDE-PIO-32         1                       2,048 Bytes     YES
-------------------------------------------------------------------------------
D:  HD-4   UDISK       32      978 MB          4 KB            978 MB
    USB                                        4,096 Bytes     YES
-------------------------------------------------------------------------------

Enter into the Abilis control-program and type the following commands.

conflog backup

or

conf backup

Copy the configuration (DRIVERS.CFG and DRIVERS.BCK) and log files (CPX.LOG, CPX.DBG and CPX.XCP).

or

Copy only the configuration files (DRIVERS.CFG and DRIVERS.BCK).

67.8.2. How to copy configuration and log files on an USB disk using the MFIDE front panel

  1. Switch on the Abilis and keep pressed the “Up” button during the system start-up. The following messages are displayed:

  2. Press “OK” button: the request to insert a floppy disk in the drive will be shown:

  3. Press “OK” button. The messages “CONFLOG BACKUP”, “IN PROGRESS...” will be shown and Abilis CPX will copy current configuration and Log files (DRIVERS.CFG, DRIVERS.BCK, DHCP.BND, CPX.LOG, CPX.DBG and CPX.XCP) to the floppy disk. During the configuration and Log files copying procedure, a message is shown informing the User about the file that is going to be copied and about the result of the operation. These messages are of the following form:

    Where:

    • FFFFFFF.FFFF is the name of the file that is going to be processed (DRIVERS.CFG, DRIVERS.BCK, DHCP.BND, CPX.LOG, CPX.DBG and CPX.XCP);

    • ... signals that the operation is still in progress;

    • done signals that the operation was successfully ended;

    • E-nn signals that an error occurred on the file that is going to be processed, nn is a decimal value.

    If the operation is successful, the messages “CONFLOG BACKUP”, “EXECUTED” are shown; otherwise the messages “CONFLOG BACKUP”, “ENDED WITH ERROR” will be displayed.

  4. After the backup phase completion, the next step of the procedure (i.e. configuration files restore phase) is initiated:

    Pressing “Left” button it is possible to go to the next step of the procedure (i.e. configuration files restore), while pressing “Left” button it is possible to end the procedure.

  5. If you press the “Left” button, these messages will be displayed:

    Press “Ok” button to proceed with Abilis CPX software initialization.

    Press “Left” button to restart Abilis CPX system.

    Press “Up” button to execute the configuration recovery procedure from the beginning once again.

67.8.3. How to copy configuration files from an USB disk to the Abilis HD/CF through the command-line interface

Insert an USB disk in one of the Abilis USB ports.

[Tip]Tip

Type the command sys disk info to verify that the USB device is correctly mounted.

[17:11:41] ABILIS_CPX:_sys disk info

Logical drive(s) information:

Drv Disk   Label       FAT     Free space      Used space      Total space
    Interface          Sectors per block       Cluster size    Bootable
-------------------------------------------------------------------------------
C:  HD-0               16      105 MB          13 MB           119 MB
    IDE-PIO-32         1                       2,048 Bytes     YES
-------------------------------------------------------------------------------
D:  HD-4   UDISK       32      978 MB          4 KB            978 MB
    USB                                        4,096 Bytes     YES
-------------------------------------------------------------------------------

Enter into the Abilis control-program and type the following commands.

conflog restore / conf restoreCopy the configuration files (DRIVERS.CFG, DRIVERS.BCK) on HD/CF.

67.8.4. How to copy configuration files from an USB disk to the Abilis HD/CF using the MFIDE front panel

  1. Switch on the Abilis and keep pressed the “Up” button during the system start-up. The following messages are displayed:

  2. Press “Left” button.

  3. Press “OK” button: the request to insert a floppy disk in the drive will be shown:

  4. Press “OK” button. The messages “CONFLOG RESTORE”, “IN PROGRESS...” will be shown and Abilis CPX will copy configuration files (DRIVERS.CFG and DRIVERS.BCK) from the floppy disk to the HD/CF. During the configuration and Log files copying procedure, a message is shown informing the user about the file that is going to be copied and about the result of the operation. These messages are of the following form:

    Where:

    • FFFFFFF.FFFF is the name of the file that is going to be processed (DRIVERS.CFG and DRIVERS.BCK);

    • ... signals that the operation is still in progress;

    • done signals that the operation was successfully ended;

    • E-nn signals that an error occurred on the file that is going to be processed, nn is a decimal value.

    If the operation is successful, the messages “CONFLOG RESTORE”, “EXECUTED” are shown; otherwise the messages “CONFLOG RESTORE”, “ENDED WITH ERROR” will be displayed.

    After the configuration files restore phase completion, it possible either to make the Abilis CPX system start-up to proceed; or to make the system to be restarted; or to re-execute the procedure from the beginning.

Prev Up Next
67.7. How to upgrade configuration files to newer firmware versions Home 67.9. How to know which kind of hardware is mounted on Abilis