| 85.9. UMTS Box | ||
|---|---|---|
 | Chapter 85. FAQ - Frequently Asked Questions |  |
| 85.9. UMTS Box | ||
|---|---|---|
| | Chapter 85. FAQ - Frequently Asked Questions | |
To ensure high quality for calls with UMTS Box, it's needed to verify that:
The Silence Compression isn't enabled
(SC:NO in the setting of
CTISYS resource, or if SC:NO
in the CTI Routings that are used by the UMTS BOX).
The GSM/UMTS signal (SIGNAL parameter) is
sufficient; to show the available signal, type the d d
ctip:<xxx> command, where
<xxx> is the number of the CTIP port
associated to the SIM card that you want to monitor.
[19:03:49] ABILIS_CPX:d d ctip:501
CTIP:501 ----------------------------------------------------------------------
SIM_320-0666666
USER:# OPSTATE:UP STATE:UP
------------------------------------------------------------------------
CH: STATE: [Q932-STATE:] CG: [SG:] CD: [SD:]
------------------------------------------------------------------------
*** All channels disconnected ***
------------------------------------------------------------------------
VOICE-STATE:READY PDN-STATE:READY SMS-STATE:READY
------------------------------------------------------------------------
NET:WIND NET-MODE:GSM ROAMING:NO
SIGNAL:11 SIGNAL-dbm:-91 RXQUAL:0
IMEI:357396012641537 IMSI:222881672196219 SIM:8939880367011211389
SMSC:+393205858500 CODEC-ISO-BW:1304000 SIM-SEL:FIX-SIM-A
CELL-MODEL:SIM5210 CELL-VER:V1.92 CELL-FEAT:VOICE,DATA,SMS
CELL:CONNECTED CELL-STATE:READY CELL-ERR:NONE
CODEC:CONNECTED CODEC-STATE:READY CODEC-ERR:NONE
CONTROL:CONNECTED CONTROL-STATE:READY CONTROL-ERR:NONE
Signal ranges (the maximum value is 30):
0-10: the signal isn't sufficient; the UMTS Box doesn't work correctly.
11-13: the signal is low; the UMTS Box can have some problems.
14-20: the signal is good.
20-30: the signal is high and the UMTS Box works correctly.
DJ:0 and
MJ:80 in the CTIR routing used
by UMTS Box in order to reduce the delays of packets.
![[Tip]](../images/tip.png) | Tip |
|---|---|
It's possible to increase the call volume setting the
...
- CELL (GSM/UMTS) defaults ---------------------------------------------
CELL-GAIN-IN:0 CELL-GAIN-OUT:0 pdn-rxbuf:30
CELL-CODEC-GAIN-IN:0 CELL-CODEC-GAIN-OUT:0
- HDLC -----------------------------------------------------------------
... |
It's possible to set the PIN code of a SIM card in the
PIN parameter of its related CTIP port.
[19:10:24] ABILIS_CPX:d p ctipe:501
CTIP:501 DESCR:SIM_320-0666666
Act card:CELL32-1<1> USER:#
Run OPSTATE:UP LOG:DS TYPE:NET-PUBLIC
signalling:CELL HOLD:NO
VOICE-ROAMING:DISABLED
NUM:* ADDRBOOK-NUM:NUM
CDO:# SIM-SEL:SIM-A
NET-MODE:GSM NET-SEL:AUTO NET:
PDN-MODE:AUTO PDN-ROAMING:DISABLED
PDN-APN:
HOLD-ENABLE-LIST:# DIAL-IN-LIST:#
LOOP:NO PIN:1234 GAIN-IN:SYS CODEC-GAIN-IN:SYS
DIALT:5 PIN2:# GAIN-OUT:SYS CODEC-GAIN-OUT:SYS
LCS-GROUP:NONE BUSY-NOCHAN:NO ![[Caution]](../images/caution.png) | Caution |
|---|---|
If you change the position of the SIM card in the UMTS Box, you
must modify the |
It's ALWAYS better to remove the PIN code from the SIM card because Abilis inserts it into the SIM for each init ctisys command.
In order to avoid that the SIM card gets blocked, Abilis can
insert the PIN code for maximum 2 times. If the value in the
PIN parameter is changed with another one wrong, the
card gets blocked.
To unlock the SIM card, it's needed to insert the PUK code using the following DEBUG command:
debug res:ctisys cmd:l1pxxxtkyyyyyyyy lsn:254, where xxx is the number of the CTIP port and yyyyyyyy is the PUK code (PUK code has to be always a 8 digit number).
The entering of PUK code, takes some time, so the CP response isn't immediate. The response then should be:
[19:12:02] ABILIS_CPX:debug res:ctisys cmd:l1p501tk12345678 lsn:254
RES:CtiSys --------------------------------------------------------------------
CTI_System_general_properties
BufferLength:63 Date/Time:05/06/2015 08:41:00 TraceTime:58954168
PUK code 12345678 sent into the GSM module.
New PIN is 1234| |  | |
| 85.8. CTISMS |  | Part VII. Separate software tools |