A “Cluster” identifies a connection, used to transport compressed phone calls, between two Abilis. Each cluster is identified with a clear label registered in the Abilis configuration.
Cluster names basically are made from 1 to 8 characters in the range '0'..'9', 'A'..'Z', 'a'..'z', '_', ':', but to support unified namespace we have to exclude the following combinations:
Internal names used for special ports: Iax
,
Sip
, Disa
,
Vo
, Vm
, Vr
,
Mix
, Sl
(and Slink),
PBX
. Case insensitive.
Names composed of just 1 or 2 or 3 numbers, e.g. 1, 21, 999.
Names Gn
and Gnn
with
n
=number, e.g. G1
and
G99
. Case insensitive.
Names G*
, *
,
**
, #
. Case insensitive.
Names Vsp-n
, Vsp-nn
,
Vsp-nnn
, used for virtual synchronous port. Case
insensitive.
Names that start with <
or
'
. By the way, <
and
'
are character already prohibited for cluster
names
The following commands to manage the CTI Clusters use:
a cticl id:xx [par:value]: adds a new CTI Cluster;
s cticl id:xx [par:value]: sets a CTI Cluster;
c cticl id:xx : clears a CTI Cluster;
d cticl: displays the CTI Cluster table.
The d cticl ? command shows all available parameters.
The example below shows how to add the cluster Abilis2
(the number associated with the cluster is 0123456).
[15:17:02] ABILIS_CPX:a cticl id:Abilis2 descr:Cluster_to_Abilis2 num:0123456
COMMAND EXECUTED [15:17:32] ABILIS_CPX:d cticl
- Not Saved (SAVE CONF), Not Refreshed (INIT) --------------------------------- Configured Clusters:6 Activated Clusters:8 ---------+----------------------+----+-----+--------+-------------+------------ CLUS: |[DESCR:] [ID:] |NUM-IN-REWRITE: |SS: |CPO: |RG-IN: |BUSY-ON-MAX: |CLIP-RULE: |NUM: |PC: |LCS-GROUP: |ADDRBOOK-NUM: |NUMx: ---------+----------------------+----+-----+--------+-------------+------------ Abilis2 [Cluster_to_Abilis2 NO NO DISABLE NO PRIVATE [ 1] ue* NO NONE NUM 0123456
Meaning of the most important parameters:
NUM-IN-REWRITE
For incoming calls, and after NUMx
and
NUM
processing, it rewrites the calling number
for not-redirected calls (RG absent) or the redirecting number for
redirected calls (RG present). Only for NUM
: not
equal to "*
".
From 1 up to 20 characters, in the range ['0'..'9', '?' '*'] or "#" optionally preceded by TON [u, i, n, o, s, h, c] and/or NP [x, e, d, t, l, p] and/or PI [a, r, m, q] and/or SI [y, v, w, z] attributes. The '*' is allowed only alone or as the last character. Any number of '?' is allowed, but only alone or at end of the sequence (E.g. "#", "*", "nnnn*", "?????", "nnnn???" or "nnnnnnnn"). See HELP ISDN ATTRIBUTES for details on attributes. See HELP ISDN VALUES for details on meaning of special values.
Tip | |
---|---|
Interesting chapter: Section 47.4.1, “NUM and NUMx parameters for incoming calls”. |
RG-IN
Enable/disable management of incoming redirecting
[DISABLE
, ENABLE
].
DISABLE
:
The incoming CALLING NUMBER is processed as usual:
If NUM
: not equal to
"*
" it is verified according to
NUMx
and NUM
parameters, rewritten with
NUM-IN-REWRITE
then passed to
CTIR.
If NUM
:*
it
is passed unnmodified and
NUM-IN-REWRITE
ignored.
If present, the incoming REDIRECTING NUMBER is ignored, thus the REDIRECTING NUMBER is not passed to CTIR.
ENABLE
:
Incoming call WITHOUT REDIRECTING NUMBER:
If NUM
: not equal to
"*
" it is verified according to
NUMx
and NUM
parameters, rewritten with
NUM-IN-REWRITE
then passed to
CTIR.
If NUM
:*
it
is passed unnmodified and
NUM-IN-REWRITE
ignored.
Incoming call WITH REDIRECTING NUMBER:
The incoming CALLING NUMBER is passed unmodified to CTIR.
If NUM
: not equal to
"*
" the REDIRECTING NUMBER is
verified according to NUMx
and
NUM
parameters, rewritten with
NUM-IN-REWRITE
then passed to
CTIR.
If NUM
:*
the
REDIRECTING NUMBER is passed unmodified and
NUM-IN-REWRITE
ignored.
Tip | |
---|---|
Interesting chapter: Section 47.4.1, “NUM and NUMx parameters for incoming calls”. |
SS
Enable/disable supplementary services [NO, YES].
Sets for which direction the Call Path Optimization is allowed
[NO
: Call Transfer isn't sent out and it's
ignored in input, IN
: Call Transfer is accepted
in input but it isn't sent out, OUT
: Call
transfer is sent out but it's ignored in input,
BID
: Call Transfer is sent out and it's accepted
in input].
NUM
Main number assigned to this cluster.
For incoming calls it verifies and eventually adds/replaces the calling number in non-redirected calls (RG absent) or the redirecting number in redirected calls (RG present).
For outgoing calls it is used by CTI routings with
OUT
:<AUTO-I>
or
<AUTO-O>
to select the cluster from the
called number.
The available values are:
*
: the Calling Number offered by CTIR
is passed transparently to the device;
#
: the Calling Number isn't passed to
the device;
##
: enforces the presentation
restricted: the Calling Number isn't passed to the
device;
nnnn
: exactly this number is passed as
Calling Number to the device;
nnnn*
: the Calling Number received from
CTIR is modified by replacing first four digits with
nnnn;
nnnn??
: similar to
nnnn*
with the difference that only an exact
number of digits as many ?
is passed after
nnnn
;
????
: only an exact number of digits as
many ?
is passed after the
nnnn
.
NUMx
Additional number(s) assigned to this cluster.
For incoming calls it verifies the calling number in non-redirected calls (RG absent) or the redirecting number in redirected calls (RG present).
For outgoing calls it is used by CTI routings with
OUT
:<AUTO-I>
or
<AUTO-O>
to select the cluster from the
called number.
From 1 up to 20 characters, in the range ['0'..'9', '?' '*'], optionally preceded by TON [u, i, n, o, s, h, c] and/or NP [x, e, d, t, l, p] attributes. One '*' is allowed only after one or more numerical characters. One or more '?' are allowed alone or after one or more numerical characters (E.g. "nnnnnnnn", "nnnn*", "?????" or "nnnn???").
Use '-
' prefix to delete a number (E.g.
"-123456"). Several numbers can be set joining values by ','. (E.g.
"NUMx:1234,5555,-77777").
LCS-GROUP
Last Calling number Service group identifier [NONE, 1..32].
BUSY-ON-MAX
Return BUSY cause when MAXCON or MAXBW are exceeded
[NO
: Return BUSY isn't sent out and it's ignored
in input, IN
: Return BUSY is accepted in input
but it isn't sent out, OUT
: Return BUSY is sent
out but it's ignored in input, BID
: Return BUSY
is sent out and it's accepted in input].
CLIP-RULE
Specifies the treatment of the CG number for calls TO the
cluster (OUTGOING) [PRIVATE
: the CG is sent
unmodified, PUBLIC
: the CG is emptied when PI is
set to RESTRICTED].
PC
Sets for which direction the Precedence Call is allowed
[NO
: Precedence Call isn't sent out and it's
ignored in input, IN
: Precedence Call is accepted
in input but it isn't sent out, OUT
: Precedence
Call is sent out but it's ignored in input, BID
:
Precedence Call is sent out and it's accepted in input]. The
priority of the sent or received call is passed transparent
mode.
ADDRBOOK-NUM
Address book phone number assigned to this cluster."#" or "NUM" or from 1 up to 20 digits ['0'..'9'], optionally preceded by TON [u, i, n, o, s, h, c] and/or NP [x, e, d, t, l, p] attributes or 'macro' (E.g.: 0'NUM' or 123'NUM.s2' or 'NUM'99).
A list of cluster numbers
(NumClus
) is automatically generated by the system; it
contains the correspondence between Clusters and their respective
numbers.
[15:22:55] ABILIS_CPX:d list
Last change: 22/04/2015 14:22:37 CET Used-Lists: 1 Used-Items: 0 Used-Resources: 80 (byte) Free-Lists:249 Free-Items: 4000 Free-Resources: 645040 (byte) Id Name Type Description Edt St RefN. First Numb ---+----------------+------+--------------------------+---+--+-----+-----+----- 1 NumClus CLNUM Automatically_generated... R 3 0 1 ------------------------------------------------------------------------------- IN:ISDN Numbers, XN:X25 NUAs, CR:CPX resources, INN:ISDN Numbers Normalized, XU:X25 UDFs, EC:CTI Clusters, IS:ISDN Sub Addresses, IP:IP Addresses, MAC:MAC Addresses, INR:ISDN Numbers Replacements, IR:IP Addresses Ranges, DN:Dialing Numbers, IN2T:ISDN Numbers to Text, IPT:Internet Protocols, TXT:Text, CLNUM:CTI Clusters Numbers, TUP:TCP/UDP ports ranges, ICAUSE:ISDN Cause codes, ICMPT:ICMP message Types, RU:Rules, OPC:OPC Unique User IDs, MR:Master Rules. ------------------------------------------------------------------------------- [15:29:34] ABILIS_CPX:d list:NumClus
LIST:NumClus - CLNUM - Ref-Numb:3 Items-Numb:1 Automatically_generated_CTI_Clusters_Numbers_list_(ReadOnly) -------------------------------------------------------------------------- 0123456 Abilis2
This list can be used to simplify the structure of the CTI Routings: a unique rule can route all the calls for the Clusters, by verifying the called number configured. See the example in the CTI Routing section further details.
Caution | |
---|---|
Changes made on the CTI Clusters aren't immediately active. To activate them, execute the initialization command init ctisys. |
For incoming calls it verifies and eventually adds/replaces the calling number in non-redirected calls (RG absent) or the redirecting number in redirected calls (RG present).
In the direct incoming call (RG absent) if the
NUM
:*
then the calling number is
passed unchanged.
[14:14:03] ABILIS_CPX:d cticl id:2
Configured Clusters:2 Activated Clusters:8
---------+----------------------+----+-----+--------+-------------+------------
CLUS: |[DESCR:]
[ID:] |NUM-IN-REWRITE: |SS: |CPO: |RG-IN: |BUSY-ON-MAX: |CLIP-RULE:
|NUM: |PC: |LCS-GROUP: |ADDRBOOK-NUM:
|NUMx:
---------+----------------------+----+-----+--------+-------------+------------
AADM - NO NO DISABLE NO PRIVATE
[ 2] * NO NONE NUM
-------------------------------------------------------------------------------
Suppose we have this CTIR rule:
[14:14:04] ABILIS_CPX:d ctir pr:0
Last change: 20/01/2016 07:12:32 CET
---+------+-----------------+---------+--------------------+--------------------
PR |[DESCR]
|BCI |POI |SR |GI |OUT |CDI |CDO
ACT|NEXT |LAST |EEC |T301|CGI |CGO
EDT|SP |SC |DJ |MJ |FMDJ|FMMJ|SDI |SDO
|SPOUT |SCOUT|DJOUT|MJOUT|LCS |LCST|SGI |SGO
| |BCO |RGI |RGO
|FMRLY |FAXSP|MODSP|FMLVL|ECM |UDT |IG |OG |SG |DL |DH
|CODERS
|CODERSOUT
|TI1 .. TI5
--------------------------------------------------------------------------------
0 VOICE # * # 101 ???* *
--------------------------------------------------------------------------------
Direct call from 767 to 555.
[14:14:08] ABILIS_CPX:start ldme
Current Local Time: Thursday 21/01/2016 14:14:59 (UTC+1.00)
Start Debug Log content real-time logging (Type CTRL+C + ENTER to stop):
Date Time Resource Ses Id Event Parameters
------ ------ ---------- ----- ---- -------------- --------------------------------------
210116 141524 CtiCl-2 40 40 E-DialRx CH:78 BC:Speech CD:ux5 CG:uxq767
USER:test2 CODERS:Spirit,G.723.1
210116 141525 CtiCl-2 40 40 E-CallRx CH:78 BC:Speech CD:ux555 CG:uxq767
USER:test2 CODERS:Spirit,G.723.1
210116 141525 CtiCl-2 40 40 E-Route Match PR:0
210116 141525 CtiP-101 40 40 E-CallTx BC:Speech TY:CtoV CD:ux555 CG:uxq767
210116 141525 CtiCl-2 40 40 E-NumComplete CDI:ux555 CDO:ux555
210116 141525 CtiP-101 40 40 E-AlertRx CH:1 USER:11
210116 141525 CtiCl-2 40 40 E-AlertTx CH:78 CODERS:Spirit
Redirected call from 777 with original calling number 767 to 555.
[14:15:38] ABILIS_CPX:start ldme
Current Local Time: Thursday 21/01/2016 14:21:46 (UTC+1.00)
Start Debug Log content real-time logging (Type CTRL+C + ENTER to stop):
210116 143117 CtiCl-2 43 43 E-CallRx CH:90 BC:Speech CD:ux555 CG:uxq767
USER:test2 CODERS:Spirit
210116 143117 CtiCl-2 43 43 E-Route Match PR:0
210116 143117 CtiP-101 43 43 E-CallTx BC:Speech TY:CtoV CD:ux555 CG:uxq767
210116 143117 CtiCl-2 43 43 E-NumComplete CDI:ux555 CDO:ux555
210116 143117 CtiP-101 43 43 E-AlertRx CH:1 USER:11
The redirected number isn't passing because the management of incoming redirecting numbers is disable.
Type the following command to enable the management of incoming redirecting numbers for this cluster:
[14:39:32] ABILIS_CPX:s cticl id:2 rg-in:enable
COMMAND EXECUTED [14:39:43] ABILIS_CPX:d cticl id:2
- Not Saved (SAVE CONF), Not Refreshed (INIT) --------------------------------- Configured Clusters:2 Activated Clusters:8 ---------+----------------------+----+-----+--------+-------------+------------ CLUS: |[DESCR:] [ID:] |NUM-IN-REWRITE: |SS: |CPO: |RG-IN: |BUSY-ON-MAX: |CLIP-RULE: |NUM: |PC: |LCS-GROUP: |ADDRBOOK-NUM: |NUMx: ---------+----------------------+----+-----+--------+-------------+------------ AADM - NO NO ENABLE NO PRIVATE [ 2] * NO NONE NUM -------------------------------------------------------------------------------
Caution | |
---|---|
Changes made on the CTI clusters aren't immediately active. To activate them, execute the initialization command init ctisys. |
Direct call from 767 to 555.
[15:03:08] ABILIS_CPX:start ldme
Current Local Time: Thursday 21/01/2016 15:03:16 (UTC+1.00)
Start Debug Log content real-time logging (Type CTRL+C + ENTER to stop):
Date Time Resource Ses Id Event Parameters
------ ------ ---------- ----- ---- -------------- --------------------------------------
210116 150319 CtiCl-2 45 45 E-DialRx CH:98 BC:Speech CD:ux5 CG:uxq767
USER:test2 CODERS:Spirit,G.723.1
210116 150320 CtiCl-2 45 45 E-CallRx CH:98 BC:Speech CD:ux555 CG:uxq767
USER:test2 CODERS:Spirit,G.723.1
210116 150320 CtiCl-2 45 45 E-Route Match PR:0
210116 150320 CtiP-101 45 45 E-CallTx BC:Speech TY:CtoV CD:ux555 CG:uxq767
210116 150320 CtiCl-2 45 45 E-NumComplete CDI:ux555 CDO:ux555
210116 150320 CtiP-101 45 45 E-AlertRx CH:1 USER:11
210116 150320 CtiCl-2 45 45 E-AlertTx CH:98 CODERS:Spirit
Redirected call from 777 with original calling number 767 to 555.
[15:07:28] ABILIS_CPX:start ldme
Current Local Time: Thursday 21/01/2016 15:07:31 (UTC+1.00)
Start Debug Log content real-time logging (Type CTRL+C + ENTER to stop):
Date Time Resource Ses Id Event Parameters
------ ------ ---------- ----- ---- -------------- --------------------------------------
210116 150742 CtiCl-2 48 48 E-CallRx CH:110 BC:Speech CD:ux555 CG:uxq767
RG:uxay777 USER:test2 CODERS:Spirit
210116 150742 CtiCl-2 48 48 E-Route Match PR:0
210116 150742 CtiP-101 48 48 E-CallTx BC:Speech TY:CtoV CD:ux555 CG:uxq767
RG:uxay777
210116 150742 CtiCl-2 48 48 E-NumComplete CDI:ux555 CDO:ux555
210116 150742 CtiP-101 48 48 E-AlertRx CH:1 USER:11
210116 150742 CtiCl-2 48 48 E-AlertTx CH:110 CODERS:Spirit
Now the new parameter RG
is present on the
call. This parameter is possible to use for CTI routings, see: Section 47.7, “Redirecting”.
Type the following command to assign 2 numbers for this cluster:
[08:20:31] ABILIS_CPX:s cticl id:2 num:888 numx:999
COMMAND EXECUTED [08:21:05] ABILIS_CPX:d cticl id:2
- Not Saved (SAVE CONF), Not Refreshed (INIT) --------------------------------- Configured Clusters:2 Activated Clusters:8 ---------+----------------------+----+-----+--------+-------------+------------ CLUS: |[DESCR:] [ID:] |NUM-IN-REWRITE: |SS: |CPO: |RG-IN: |BUSY-ON-MAX: |CLIP-RULE: |NUM: |PC: |LCS-GROUP: |ADDRBOOK-NUM: |NUMx: ---------+----------------------+----+-----+--------+-------------+------------ AADM ue* NO NO ENABLE NO PRIVATE [ 2] 888 NO NONE NUM 999 ------------------------------------------------------------------------------
Caution | |
---|---|
Changes made on the CTI clusters aren't immediately active. To activate them, execute the initialization command init ctisys. |
Direct call from 767 to 555.
[08:26:01] ABILIS_CPX:start ldme
Current Local Time: Friday 22/01/2016 08:26:21 (UTC+1.00)
Start Debug Log content real-time logging (Type CTRL+C + ENTER to stop):
Date Time Resource Ses Id Event Parameters
------ ------ ---------- ----- ---- -------------- --------------------------------------
220116 082624 CtiCl-2 82 82 E-DialRx CH:42 BC:Speech CD:ux5 CG:ueq888
USER:test2 CODERS:Spirit,G.723.1
220116 082624 CtiCl-2 82 82 E-CallRx CH:42 BC:Speech CD:ux555 CG:ueq888
USER:test2 CODERS:Spirit,G.723.1
220116 082624 CtiCl-2 82 82 E-Route Match PR:0
220116 082624 CtiP-101 82 82 E-CallTx BC:Speech TY:CtoV CD:ux555 CG:ueq888
220116 082624 CtiCl-2 82 82 E-NumComplete CDI:ux555 CDO:ux555
220116 082624 CtiP-101 82 82 E-AlertRx CH:1 USER:11
220116 082624 CtiCl-2 82 82 E-AlertTx CH:42 CODERS:Spirit
Because for this cluster now the NUM
and
NUMx
parameters are present, the original calling
number (767) is changed with the NUM parameter (888). When the
NUM
and NUMx
parameters are
configured the calling number is verified with the
NUM
and NUMx
parameters, if the
calling number is different, then it's changed with
NUM
parameter.
Redirected call from 777 with original calling number 767 to 555.
[08:32:16] ABILIS_CPX:start ldme
Current Local Time: Friday 22/01/2016 08:32:19 (UTC+1.00)
Start Debug Log content real-time logging (Type CTRL+C + ENTER to stop):
Date Time Resource Ses Id Event Parameters
------ ------ ---------- ----- ---- -------------- --------------------------------------
220116 083223 CtiCl-2 83 83 E-CallRx CH:46 BC:Speech CD:ux555 CG:uxq767
RG:ueay888 USER:test2 CODERS:Spirit
220116 083223 CtiCl-2 83 83 E-Route Match PR:0
220116 083223 CtiP-101 83 83 E-CallTx BC:Speech TY:CtoV CD:ux555 CG:uxq767
RG:ueay888
220116 083223 CtiCl-2 83 83 E-NumComplete CDI:ux555 CDO:ux555
220116 083223 CtiP-101 83 83 E-AlertRx CH:1 USER:11
220116 083223 CtiCl-2 83 83 E-AlertTx CH:46 CODERS:Spirit
When the RG
parameter is present in the call
and NUM
and NUMx
parameters are
configured for cluster, then the redirected number (777) is changed with
the NUM
parameter (888). When the
NUM
and NUMx
parameters are
configured and the RG
parameter is present, the
redirected number is verified with the NUM
and
NUMx
parameters, if the redirected number is
different, then it's changed with NUM
parameter. The
calling number in this situation is passed unchanged.
Type the following command to configure the
NUM-IN-REWRITE
parameter for this cluster:
[08:43:11] ABILIS_CPX:s cticl id:2 num-in-rewrite:ue7*
COMMAND EXECUTED [08:43:45] ABILIS_CPX:d cticl id:2
- Not Saved (SAVE CONF), Not Refreshed (INIT) --------------------------------- Configured Clusters:2 Activated Clusters:8 ---------+----------------------+----+-----+--------+-------------+------------ CLUS: |[DESCR:] [ID:] |NUM-IN-REWRITE: |SS: |CPO: |RG-IN: |BUSY-ON-MAX: |CLIP-RULE: |NUM: |PC: |LCS-GROUP: |ADDRBOOK-NUM: |NUMx: ---------+----------------------+----+-----+--------+-------------+------------ AADM ue7* NO NO ENABLE NO PRIVATE [ 2] 888 NO NONE NUM 999 -------------------------------------------------------------------------------
Caution | |
---|---|
Changes made on the CTI clusters aren't immediately active. To activate them, execute the initialization command init ctisys. |
Direct call from 767 to 555.
[08:45:15] ABILIS_CPX:start ldme
Current Local Time: Friday 22/01/2016 08:45:20 (UTC+1.00)
Start Debug Log content real-time logging (Type CTRL+C + ENTER to stop):
Date Time Resource Ses Id Event Parameters
------ ------ ---------- ----- ---- -------------- --------------------------------------
220116 084525 CtiCl-2 84 84 E-DialRx CH:50 BC:Speech CD:ux5 CG:ueq788
USER:test2 CODERS:Spirit,G.723.1
220116 084526 CtiCl-2 84 84 E-CallRx CH:50 BC:Speech CD:ux555 CG:ueq788
USER:test2 CODERS:Spirit,G.723.1
220116 084526 CtiCl-2 84 84 E-Route Match PR:0
220116 084526 CtiP-101 84 84 E-CallTx BC:Speech TY:CtoV CD:ux555 CG:ueq788
220116 084526 CtiCl-2 84 84 E-NumComplete CDI:ux555 CDO:ux555
220116 084526 CtiP-101 84 84 E-AlertRx CH:1 USER:11
220116 084526 CtiCl-2 84 84 E-AlertTx CH:50 CODERS:Spirit
When the NUM-IN-REWRITE
parameter is configured
the original calling number is changed twice. First change is with
NUM
parameter (from 767 to 888) and the second change
is the NUM with NUM-IN-REWRITE
(from 888 to 788). The
NUM-IN-REWRITE
:ue7*
means what the
first digit is changed with 7 and the following digits are passed
unchanged.
Redirected call from 777 with original calling number 767 to 555.
[08:54:52] ABILIS_CPX:start ldme
Current Local Time: Friday 22/01/2016 08:54:55 (UTC+1.00)
Start Debug Log content real-time logging (Type CTRL+C + ENTER to stop):
Date Time Resource Ses Id Event Parameters
------ ------ ---------- ----- ---- -------------- --------------------------------------
220116 085458 CtiCl-2 85 85 E-CallRx CH:54 BC:Speech CD:ux555 CG:uxq767
RG:ueay788 USER:test2 CODERS:Spirit
220116 085458 CtiCl-2 85 85 E-Route Match PR:0
220116 085458 CtiP-101 85 85 E-CallTx BC:Speech TY:CtoV CD:ux555 CG:uxq767
RG:ueay788
220116 085458 CtiCl-2 85 85 E-NumComplete CDI:ux555 CDO:ux555
220116 085458 CtiP-101 85 85 E-AlertRx CH:1 USER:11
220116 085458 CtiCl-2 85 85 E-AlertTx CH:54 CODERS:Spirit
When the RG
parameter is present in the call
and NUM
, NUMx
and
NUM-IN-REWRITE
parameters are configured for cluster,
then the redirected number (777) is changed with the
NUM
parameter (888) and the NUM
parameter (888) is changed with NUM-IN-REWRITE
parameter (obtaining the redirected number 788). The
NUM-IN-REWRITE
:ue7*
means what the
first digit is changed with 7 and the following digits are passed
unchanged.
We will follow the same situation when RG-IN
is
disabled. Type the following command to disable the management of
incoming redirecting numbers for this cluster:
[09:21:09] ABILIS_CPX:s cticl id:2 rg-in:disable
COMMAND EXECUTED [09:21:20] ABILIS_CPX:d cticl id:2
- Not Saved (SAVE CONF), Not Refreshed (INIT) --------------------------------- Configured Clusters:2 Activated Clusters:8 ---------+----------------------+----+-----+--------+-------------+------------ CLUS: |[DESCR:] [ID:] |NUM-IN-REWRITE: |SS: |CPO: |RG-IN: |BUSY-ON-MAX: |CLIP-RULE: |NUM: |PC: |LCS-GROUP: |ADDRBOOK-NUM: |NUMx: ---------+----------------------+----+-----+--------+-------------+------------ AADM ue7* NO NO DISABLE NO PRIVATE [ 2] 888 NO NONE NUM 999 -------------------------------------------------------------------------------
Caution | |
---|---|
Changes made on the CTI clusters aren't immediately active. To activate them, execute the initialization command init ctisys. |
Direct call from 767 to 555.
[09:38:30] ABILIS_CPX:start ldme
Current Local Time: Friday 22/01/2016 09:38:34 (UTC+1.00)
Start Debug Log content real-time logging (Type CTRL+C + ENTER to stop):
Date Time Resource Ses Id Event Parameters
------ ------ ---------- ----- ---- -------------- --------------------------------------
220116 093838 CtiCl-2 86 86 E-DialRx CH:58 BC:Speech CD:ux5 CG:ueq788
USER:test2 CODERS:Spirit,G.723.1
220116 093838 CtiCl-2 86 86 E-CallRx CH:58 BC:Speech CD:ux555 CG:ueq788
USER:test2 CODERS:Spirit,G.723.1
220116 093838 CtiCl-2 86 86 E-Route Match PR:0
220116 093838 CtiP-101 86 86 E-CallTx BC:Speech TY:CtoV CD:ux555 CG:ueq788
220116 093838 CtiCl-2 86 86 E-NumComplete CDI:ux555 CDO:ux555
220116 093838 CtiP-101 86 86 E-AlertRx CH:1 USER:11
220116 093838 CtiCl-2 86 86 E-AlertTx CH:58 CODERS:Spirit
When the NUM-IN-REWRITE
parameter is configured
the original calling number is changed twice. First change is with
NUM
parameter (from 767 to 888) and the second change
is the NUM
with NUM-IN-REWRITE
(from 888 to 788). The
NUM-IN-REWRITE
:ue7*
means what the
first digit is changed with 7 and the following digits are passed
unchanged.
Redirected call from 777 with original calling number 767 to 555.
[09:38:49] ABILIS_CPX:start ldme
Current Local Time: Friday 22/01/2016 09:42:10 (UTC+1.00)
Start Debug Log content real-time logging (Type CTRL+C + ENTER to stop):
Date Time Resource Ses Id Event Parameters
------ ------ ---------- ----- ---- -------------- --------------------------------------
220116 094214 CtiCl-2 87 87 E-CallRx CH:62 BC:Speech CD:ux555 CG:ueq788
USER:test2 CODERS:Spirit
220116 094214 CtiCl-2 87 87 E-Route Match PR:0
220116 094214 CtiP-101 87 87 E-CallTx BC:Speech TY:CtoV CD:ux555 CG:ueq788
220116 094214 CtiCl-2 87 87 E-NumComplete CDI:ux555 CDO:ux555
220116 094214 CtiP-101 87 87 E-AlertRx CH:1 USER:11
220116 094214 CtiCl-2 87 87 E-AlertTx CH:62 CODERS:Spirit
It is the same as the above example, because the
RG-IN
is disabled for this cluster, and the
redirected number isn't passed for this call. The calling number changes
in this situation.
We will follow the same situation when RG-IN
is
disabled and the NUM-IN-REWRITE
have the default
value ue*
. Type the following command to set the
NUM-IN-REWRITE
to the default value for this
cluster:
[09:55:58] ABILIS_CPX:s cticl id:2 num-in-rewrite:ue*
COMMAND EXECUTED [09:56:06] ABILIS_CPX:d cticl id:2
- Not Saved (SAVE CONF), Not Refreshed (INIT) --------------------------------- Configured Clusters:2 Activated Clusters:8 ---------+----------------------+----+-----+--------+-------------+------------ CLUS: |[DESCR:] [ID:] |NUM-IN-REWRITE: |SS: |CPO: |RG-IN: |BUSY-ON-MAX: |CLIP-RULE: |NUM: |PC: |LCS-GROUP: |ADDRBOOK-NUM: |NUMx: ---------+----------------------+----+-----+--------+-------------+------------ AADM ue* NO NO DISABLE NO PRIVATE [ 2] 888 NO NONE NUM 999 -------------------------------------------------------------------------------
Caution | |
---|---|
Changes made on the CTI clusters aren't immediately active. To activate them, execute the initialization command init ctisys. |
Direct call from 767 to 555.
[09:57:20] ABILIS_CPX:start ldme
Current Local Time: Friday 22/01/2016 09:57:26 (UTC+1.00)
Start Debug Log content real-time logging (Type CTRL+C + ENTER to stop):
Date Time Resource Ses Id Event Parameters
------ ------ ---------- ----- ---- -------------- --------------------------------------
220116 095739 CtiCl-2 88 88 E-DialRx CH:66 BC:Speech CD:ux5 CG:ueq888
USER:test2 CODERS:Spirit,G.723.1
220116 095739 CtiCl-2 88 88 E-CallRx CH:66 BC:Speech CD:ux555 CG:ueq888
USER:test2 CODERS:Spirit,G.723.1
220116 095739 CtiCl-2 88 88 E-Route Match PR:0
220116 095739 CtiP-101 88 88 E-CallTx BC:Speech TY:CtoV CD:ux555 CG:ueq888
220116 095739 CtiCl-2 88 88 E-NumComplete CDI:ux555 CDO:ux555
220116 095739 CtiP-101 88 88 E-AlertRx CH:1 USER:11
220116 095739 CtiCl-2 88 88 E-AlertTx CH:66 CODERS:Spirit
Because for this cluster now the NUM
and
NUMx
parameters are present, the original calling
number (767) is changed with the NUM
parameter (888).
When the NUM
and NUMx
parameters
are configured the calling number is verified with the
NUM
and NUMx
parameters, if the
calling number is different, then it's changed with
NUM
parameter.
Redirected call from 777 with original calling number 767 to 555.
[09:58:56] ABILIS_CPX:start ldme
Current Local Time: Friday 22/01/2016 09:59:02 (UTC+1.00)
Start Debug Log content real-time logging (Type CTRL+C + ENTER to stop):
Date Time Resource Ses Id Event Parameters
------ ------ ---------- ----- ---- -------------- --------------------------------------
220116 095905 CtiCl-2 89 89 E-CallRx CH:70 BC:Speech CD:ux555 CG:ueq888
USER:test2 CODERS:Spirit
220116 095905 CtiCl-2 89 89 E-Route Match PR:0
220116 095905 CtiP-101 89 89 E-CallTx BC:Speech TY:CtoV CD:ux555 CG:ueq888
220116 095905 CtiCl-2 89 89 E-NumComplete CDI:ux555 CDO:ux555
220116 095905 CtiP-101 89 89 E-AlertRx CH:1 USER:11
220116 095905 CtiCl-2 89 89 E-AlertTx CH:70 CODERS:Spirit
It's the same as the above example, because the
RG-IN
is disabled for this cluster, and the
redirected number isn't passed for this call. The calling number changes
in this situation.
To delete a number from a cluster, type the following command:
[11:04:03] ABILIS_CPX:s cticl id:2 numx:-999
COMMAND EXECUTED [11:04:23] ABILIS_CPX:d cticl id:2
- Not Saved (SAVE CONF), Not Refreshed (INIT) --------------------------------- Configured Clusters:2 Activated Clusters:8 ---------+----------------------+----+-----+--------+-------------+------------ CLUS: |[DESCR:] [ID:] |NUM-IN-REWRITE: |SS: |CPO: |RG-IN: |BUSY-ON-MAX: |CLIP-RULE: |NUM: |PC: |LCS-GROUP: |ADDRBOOK-NUM: |NUMx: ---------+----------------------+----+-----+--------+-------------+------------ AADM ue* NO NO DISABLE NO PRIVATE [ 2] 888 NO NONE NUM -------------------------------------------------------------------------------
Caution | |
---|---|
Changes made on the CTI clusters aren't immediately active. To activate them, execute the initialization command init ctisys. |
For outgoing calls NUM
and
NUMx
are used by CTI
routings with
OUT
:<AUTO-I>
or
<AUTO-O>
to select the cluster from the called
number:
<AUTO-I>
: by specifying this value
in OUT
, the routing will be matched according to
the standard rules. The destination cluster will be chosen by
comparing the field CDI
with the NUMs set in each
cluster. When the match is found, the corresponding cluster will be
the real destination of the call.
<AUTO-O>
: by specifying this value
in OUT
, the routing will be matched according to
the standard rules. The destination cluster will be chosen by
comparing the field CDO
with the NUMs set in each
cluster. When the match is found, the corresponding cluster will be
the real destination of the call.
These values are useful to reduce the number of rules in the CTIR
table, but to use these values is needed to configure for cluster the
NUM
and NUMx
parameters.
Suppose we have four clusters:
[08:51:37] ABILIS_CPX:d cticl
- Not Saved (SAVE CONF), Not Refreshed (INIT) ---------------------------------
Configured Clusters:4 Activated Clusters:8
---------+----------------------+----+-----+--------+-------------+------------
CLUS: |[DESCR:]
[ID:] |NUM-IN-REWRITE: |SS: |CPO: |RG-IN: |BUSY-ON-MAX: |CLIP-RULE:
|NUM: |PC: |LCS-GROUP: |ADDRBOOK-NUM:
|NUMx:
---------+----------------------+----+-----+--------+-------------+------------
AADM ue* NO NO DISABLE NO PRIVATE
[ 2] 888 NO NONE NUM
-------------------------------------------------------------------------------
Antek - NO NO DISABLE NO PRIVATE
[ 1] * NO NONE NUM
-------------------------------------------------------------------------------
test - NO NO DISABLE NO PRIVATE
[ 3] * NO NONE NUM
-------------------------------------------------------------------------------
test2 - NO NO DISABLE NO PRIVATE
[ 4] * NO NONE NUM
-------------------------------------------------------------------------------
Suppose we have this CTIR table:
[09:00:44] ABILIS_CPX:d ctir
- Not Saved (SAVE CONF), Not Refreshed (INIT) ---------------------------------
Last change: 25/01/2016 09:00:20 CET
---+------+-----------------+---------+--------------------+--------------------
PR |[DESCR]
|BCI |POI |SR |GI |OUT |CDI |CDO
ACT|NEXT |LAST |EEC |T301|CGI |CGO
EDT|SP |SC |DJ |MJ |FMDJ|FMMJ|SDI |SDO
|SPOUT |SCOUT|DJOUT|MJOUT|LCS |LCST|SGI |SGO
| |BCO |RGI |RGO
|FMRLY |FAXSP|MODSP|FMLVL|ECM |UDT |IG |OG |SG |DL |DH
|CODERS
|CODERSOUT
|TI1 .. TI5
--------------------------------------------------------------------------------
0 VOICE PBX # # AADM 888 *
--------------------------------------------------------------------------------
1 VOICE PBX # # Antek 777 *
--------------------------------------------------------------------------------
2 VOICE PBX # # test 666 *
--------------------------------------------------------------------------------
3 VOICE PBX # # test 55? *
--------------------------------------------------------------------------------
To reduce the number of rules in the CTIR table, the first step is needed to configure for clusters the NUM and NUMx parameters:
[09:23:32] ABILIS_CPX:s cticl id:1 num:777
COMMAND EXECUTED [09:24:28] ABILIS_CPX:s cticl id:3 num:666
COMMAND EXECUTED [09:24:42] ABILIS_CPX:s cticl id:4 num:55?
COMMAND EXECUTED [09:25:20] ABILIS_CPX:d cticl
- Not Saved (SAVE CONF), Not Refreshed (INIT) --------------------------------- Configured Clusters:4 Activated Clusters:8 ---------+----------------------+----+-----+--------+-------------+------------ CLUS: |[DESCR:] [ID:] |NUM-IN-REWRITE: |SS: |CPO: |RG-IN: |BUSY-ON-MAX: |CLIP-RULE: |NUM: |PC: |LCS-GROUP: |ADDRBOOK-NUM: |NUMx: ---------+----------------------+----+-----+--------+-------------+------------ AADM ue* NO NO DISABLE NO PRIVATE [ 2] 888 NO NONE NUM ------------------------------------------------------------------------------- Antek ue* NO NO DISABLE NO PRIVATE [ 1] 777 NO NONE NUM ------------------------------------------------------------------------------- test ue* NO NO DISABLE NO PRIVATE [ 3] 666 NO NONE NUM ------------------------------------------------------------------------------- test2 ue* NO NO DISABLE NO PRIVATE [ 4] 55? NO NONE NUM -------------------------------------------------------------------------------
Caution | |
---|---|
Changes made on the CTI clusters aren't immediately active. To activate them, execute the initialization command init ctisys. |
Type the following command to add a rule with
<AUTO-I>
value for the OUT
field.
[09:30:52] ABILIS_CPX:a ctir pr:0 poi:pbx out:<auto-i> cdi:'numclus'
COMMAND EXECUTED [09:36:44] ABILIS_CPX:d ctir pr:0
Last change: 25/01/2016 09:31:44 CET ---+------+-----------------+---------+--------------------+-------------------- PR |[DESCR] |BCI |POI |SR |GI |OUT |CDI |CDO ACT|NEXT |LAST |EEC |T301|CGI |CGO EDT|SP |SC |DJ |MJ |FMDJ|FMMJ|SDI |SDO |SPOUT |SCOUT|DJOUT|MJOUT|LCS |LCST|SGI |SGO | |BCO |RGI |RGO |FMRLY |FAXSP|MODSP|FMLVL|ECM |UDT |IG |OG |SG |DL |DH |CODERS |CODERSOUT |TI1 .. TI5 -------------------------------------------------------------------------------- 0 VOICE PBX # # <AUTO-I> 'NumClus' * --------------------------------------------------------------------------------
Warning | |
---|---|
Changes made on the CTI routing table aren't immediately active. To activate them, execute the initialization command init ctir. |
Now we have just one rule, those old can be deleted, see: Section 47.5.3, “Clear CTI Routing Table (C CTIR)”.
To transfer compressed phone calls the CTI Link associates a cluster with a data resource.
The data resources that may be associated with clusters are:
AIPT (Abilis IP Tunnel)
PV (Packet Voice)
NPV (New Packet Voice)
The following commands to manage the CTI Links use:
a ctil id:xx [par:value]: adds a new CTI Link;
s ctil id:xx [par:value]: sets a CTI Link;
c ctil id:xx: clears a CTI Link;
d ctil: displays the CTI Link table.
The d ctil ? command shows all available parameters.
The example below shows how to associate the cluster
Abilis2
with the resource PV-1
.
[15:55:24] ABILIS_CPX:a ctil id:1 res:pv-1 clus:abilis2 maxbw:64000
COMMAND EXECUTED [15:55:35] ABILIS_CPX:d ctil
- Not Saved (SAVE CONF) ------------------------------------------------------- Configured Links:1 ID: RES: CLUS: MAXBW: MAXCON: GROUP: (GROUP-MAXBW: GROUP-MAXCON:) ------------------------------------------------------------------------------- 1 Pv-1 Abilis2 64000 NOMAX NONE
Tip | |
---|---|
For each CTI Link you can define a maximum bandwidth to use with
compressed phone calls; this could be very interesting if you want to
limit the number of calls toward a specific direction. A link inside a
group and a further maximum bandwidth ( |
Caution | |
---|---|
Changes made on the CTI Links aren't immediately active. To activate them, execute the initialization command init ctisys. |
CTI Link can be joined together in groups. For each group a value of MAX Bandwidth can be established. This can be very useful to limit the number of simultaneous compressed calls for the CTI Links which belong to the group.
The following commands to manage the CTI Link Groups use:
a ctilg id:<ctilg_number> [group-maxbw:<maxbw_value>] [descr:<description>]: adds a new CTI Link Group;
s ctilg id:<ctilg_number> [group-maxbw:<maxbw_value>] [descr:<description>]: sets an existing CTI Link Group;
c ctilg id:<ctilg_number>: clears a CTI Link Group;
d ctilg [id:<ctilg_number>]: displays the list of CTI Link Group or a specific one.
The d ctilg ? command shows all available parameters. The Example below shows how to create a new CTI Link Group and how join a CTI Link in the group.
[09:31:12] ABILIS_CPX:a ctilg id:1 group-maxbw:64000 descr:Collaborators
COMMAND EXECUTED [09:37:00] ABILIS_CPX:d ctilg
- Not Saved (SAVE CONF), Not Refreshed (INIT) --------------------------------- ID: GROUP-MAXBW: GROUP-MAXCON: DESCR: ------------------------------------------------------------------------------- 1 64000 NOMAX Collaborators [11:28:10] ABILIS_CPX:d ctil
- Not Saved (SAVE CONF), Not Refreshed (INIT) --------------------------------- Configured Links:1 Activated Links:8 ID: RES: CLUS: MAXBW: MAXCON: GROUP: (GROUP-MAXBW: GROUP-MAXCON:) ------------------------------------------------------------------------------- 1 Pv-1 Abilis2 64000 NOMAX NONE [11:28:23] ABILIS_CPX:s ctil id:1 group:1
COMMAND EXECUTED [11:28:43] ABILIS_CPX:d ctil
- Not Saved (SAVE CONF), Not Refreshed (INIT) --------------------------------- Configured Links:1 Activated Links:8 ID: RES: CLUS: MAXBW: MAXCON: GROUP: (GROUP-MAXBW: GROUP-MAXCON:) ------------------------------------------------------------------------------- 1 Pv-1 Abilis2 64000 NOMAX 1 ( 64000 NOMAX)
Caution | |
---|---|
Changes made on the CTI Link Groups aren't immediately active. To activate them, execute the initialization command init ctisys. |