| 16.4. IOBOX diagnostics and statistics | ||
|---|---|---|
 | Chapter 16. IOBOX |  |
| 16.4. IOBOX diagnostics and statistics | ||
|---|---|---|
| | Chapter 16. IOBOX | |
This command reports the current situation of the device:
[13:42:55] ABILIS_CPX:d d gpio
RES:Gpio-1 --------------------------------------------------------------------
STATE:UP USB-STATE:CONNECTED
- Digital Input Lines State --------------------------------------------
1..16| off off off off off off off off . . . . . . . .
------------------------------------------------------------------------
- Digital Output Lines State -------------------------------------------
1..16| off off off off . . . . . . . . . . . .
------------------------------------------------------------------------
- Analog Input Lines ---------------------------------------------------
| State Value Unit ADC | State Value Unit ADC
------+--------------------------------+--------------------------------
1.. 2| NORMAL 10 C 0 | NORMAL 0.0 % 0
3.. 4| . . . . | . . . .
5.. 6| . . . . | . . . .
7.. 8| . . . . | . . . .
------------------------------------------------------------------------The meaning:
STATEGPIO driver state:
DOWN - device stopped or
disconnected.
UP - device running.
INACTIVE - device good, but
inactive (configuration parameter
ACT:NO).
USB-STATEUSB device connection state:
DISCONNECTED - device disconnected
from USB port.
CONNECTED - device
connected.
D-IN:1...8 / D-OUT:1...4GPIO digital input/output line state:
OFF - logical 0 state.
ON - logical 1 state.
N/A (not available) - unknown
state.
StateGPIO analog input line state:
LOW - under the low
threshold.
NORMAL - between high and low
threshold.
HIGH - between high and low
threshold.
N/A (not available) - unknown
state.
ValueGPIO analog input line value. N/A (not
available) - unknown state.
UnitUnit for analog input/output lines.
ADCConverted value from ADC value on analog input/output lines.
This command can help to understand what is happening, in case of troubles:
[13:48:36] ABILIS_CPX:d s gpio
RES:Gpio-1 --------------------------------------------------------------------
--- Cleared 13 days 21:06:37 ago, on 11/08/2017 at 18:08:13 ------------
-----------|---INPUT---|--OUTPUT---|-----------|---INPUT---|--OUTPUT---|
USB-CONN | 67| |USB-DISC | | 66|
USB-AUTRST | 0| | | | |
CHR | 17650515| 13290463|FRM | 2777250| 2777271|
------------------------------------------------------------------------With reference to the shown interval of time («Cleared 13 days 21:06:37 ago») these counters show the number of:
USB-CONN | USB connections. |
USB-DISC | USB disconnections. |
USB-AUTRST | USB autorestarts. Troubles on USB interface. |
CHR | Bytes in received/transmitted frames. |
FRM | Received/transmitted frames. |
This command reports the current situation of the device:
[13:42:55] ABILIS_CPX:d d mfio
RES:MfIo ----------------------------------------------------------------------
Abilis_Multi_Function_IO_Interface
STATE:ACTIVE
- Digital Input Lines State --------------------------------------------
1..7| off off off off off off off
------------------------------------------------------------------------
- Digital Output Lines State -------------------------------------------
1..7| off off off off off off off
------------------------------------------------------------------------The meaning:
STATEMFIO driver state:
ACTIVE - device running.
INACTIVE - device good, but
inactive (configuration parameter
ACT:NO).
D-IN:1...7 / D-OUT:1...7MFIO digital input/output line state:
OFF - logical 0 state.
ON - logical 1 state.
N/A (not available) - unknown
state.
This command can help to understand what is happening, in case of troubles:
[13:48:36] ABILIS_CPX:d s mfio
RES:MfIo ----------------------------------------------------------------------
Abilis_Multi_Function_IO_Interface
--- Cleared 0 days 13:21:08 ago, on 25/08/2017 at 02:02:40 -------------
-----------|---INPUT---|--OUTPUT---|-----------|---INPUT---|--OUTPUT---|
IRQ | 35| | | | |
STATE | 2| |ERR-STATE | 0| |
LINE-STATE | 63| |ERR-LINE-ST| 0| |
ALARM | 63| |ERR-ALARM | 0| |
------------------------------------------------------------------------With reference to the shown interval of time («Cleared 0 days 13:21:08 ago») these counters show the number of:
IRQ | MFIO interrupts. |
STATE | Set State requests. |
LINE-STATE | Set Line State requests. |
ALARM | Set Alarm requests. |
ERR-STATE | Errors during Set State. |
ERR-LINE-ST | Errors during Set Line State. |
ERR-ALARM | Errors during Set Alarm. |
![[Note]](../images/note.png) | Note |
|---|---|
If you notice incrementation of |
This command reports the current situation of the device:
[13:42:55] ABILIS_CPX:d d rvs
RES:Rvs-1 ---------------------------------------------------------------------
STATE:UP MAC:B8-27-EB-93-FA-DF
RemAdd-RemPort:192.168.029.101-41414
CURRENT-IMAGE:5.000 FACTORY-IMAGE:5.000 BOARD:0.0
- Digital Input Lines State --------------------------------------------
1.. 4| ON ON ON ON
------------------------------------------------------------------------
- Digital Output Lines State -------------------------------------------
1.. 4| off ON off off
------------------------------------------------------------------------
- Cameras diagnostics --------------------------------------------------
CAM: State: LIVE: LIVE-REC: ALARM-REC: STORED-ALARMS: STORED-LIVE:
------------------------------------------------------------------------
Cam-1 UP 0 NO NO 54 0
------------------------------------------------------------------------The meaning:
STATERVS driver state:
DOWN - device is down.
UP - device is active and
ready.
INACTIVE - device is
inactive.
MACRVS device driver MAC address.
RemAdd-RemPortRemote IP address and remote port.
CURRENT-IMAGECurrent image version.
FACTORY-IMAGEFactory image version.
D-IN:1...4 / D-OUT:1...4RVS digital input/output line state:
OFF - logical 0 state.
ON - logical 1 state.
. (not available) - unknown
state.
This command can help to understand what is happening, in case of troubles:
[13:48:36] ABILIS_CPX:d s rvs
RES:Rvs-1 ---------------------------------------------------------------------
--- Cleared 0 days 14:12:29 ago, on 25/08/2017 at 02:02:39 -------------
-----------|---INPUT---|--OUTPUT---|-----------|---INPUT---|--OUTPUT---|
CONN-SUCC | | 1|BOARD-ERR | 0| |
CONN-FAIL | | 0| | | |
CLOSE | 0| 0| | | |
CFG-FAIL | 0| |SET-AO-CUT | 0| |
SET-FAIL | | 0| | | |
PROT-ERR | 0| 0| | | |
IMAGE-ERR | 0| | |
------------------------------------------------------------------------With reference to the shown interval of time («Cleared 0 days 14:12:29») these counters show the number of:
CONN-SUCC | Successful opened sessions, at least a response received. |
CONN-FAIL | Aborted sessions (on opening), TCP failed or no response received. |
CFG-FAIL | Failed configuration of digital/analog parameters. |
SET-FAIL | Failed setting of digital/analog outputs. |
PROT-ERR | JMUX Errors. |
BOARD-ERR | Connections aborted on Missing board. |
SET-AO-CUT | Setting of analog outputs that where cutted. |
| Note |
|---|---|
If you notice incrementation of these counters consult Abilis support (tem@antek.it). |
This command reports the current situation of the device:
[13:42:55] ABILIS_CPX:d d rio
RES:Rio-1 ---------------------------------------------------------------------
RIO
STATE:UP MAC:B8-27-EB-12-F7-FB
RemAdd-RemPort:192.168.001.222-41414
CURRENT-IMAGE:5.001 FACTORY-IMAGE:5.001 BOARD:1.6
- Digital Input Lines State --------------------------------------------
1.. 8| ON ON ON ON ON ON ON ON
------------------------------------------------------------------------
- Digital Output Lines State -------------------------------------------
1.. 8| off off off off off off off off
------------------------------------------------------------------------
- Analog Input Lines ---------------------------------------------------
| State Value Unit ADC | State Value Unit ADC
------+--------------------------------+--------------------------------
1.. 2| NORMAL 50.0 % 2048 | NORMAL 50.0 % 2048
3.. 4| NORMAL 50.0 % 2048 | NORMAL 50.0 % 2048
------------------------------------------------------------------------
- Analog Output Lines --------------------------------------------------
| State Value Unit ADC | State Value Unit ADC
------+--------------------------------+--------------------------------
1.. 2| NORMAL 0.0 % 0 | NORMAL 0.0 % 0
3.. 4| NORMAL 0.0 % 0 | NORMAL 0.0 % 0
------------------------------------------------------------------------The meaning:
STATERIO driver state:
DOWN - device is down.
UP - device is active and
ready.
INACTIVE - device is
inactive.
MACRIO device driver MAC address.
RemAdd-RemPortRemote IP address and remote port.
CURRENT-IMAGECurrent image version.
FACTORY-IMAGEFactory image version.
D-IN:1...8 / D-OUT:1...8RIO digital input/output line state:
OFF - logical 0 state.
ON - logical 1 state.
. (not available) - unknown
state.
StateRIO analog input/output line state:
LOW - under the low
threshold.
NORMAL - between high and low
threshold.
HIGH - between high and low
threshold.
. (not available) - unknown
state.
ValueRIO analog input line value. N/A (not
available) - unknown state.
UnitUnit for analog input/output lines.
ADCConverted value from ADC value on analog input/output lines.
This command can help to understand what is happening, in case of troubles:
[13:48:36] ABILIS_CPX:d s rio
RES:Rio-1 ---------------------------------------------------------------------
RIO
--- Cleared 17 days 01:07:47 ago, on 08/08/2017 at 15:19:38 ------------
-----------|---INPUT---|--OUTPUT---|-----------|---INPUT---|--OUTPUT---|
CONN-SUCC | | 1|BOARD-ERR | 0| |
CONN-FAIL | | 0| | | |
CLOSE | 0| 0| | | |
CFG-FAIL | 0| |SET-AO-CUT | 0| |
SET-FAIL | | 0| | | |
PROT-ERR | 0| 0| | | |
------------------------------------------------------------------------With reference to the shown interval of time («Cleared 17 days 01:07:47 ago») these counters show the number of:
CONN-SUCC | Successful opened sessions, at least a response received. |
CONN-FAIL | Aborted sessions (on opening), TCP failed or no response received. |
CFG-FAIL | Failed configuration of digital/analog parameters. |
SET-FAIL | Failed setting of digital/analog outputs. |
PROT-ERR | JMUX Errors. |
BOARD-ERR | Connections aborted on Missing board. |
SET-AO-CUT | Setting of analog outputs that where cutted. |
| Note |
|---|---|
If you notice incrementation of these counters consult Abilis support (tem@antek.it). |
| |  | |
| 16.3. Activating IOBOX devices |  | 16.5. Activation of the alarms for IOBOX devices |