86.1. System Log messages

86.1. System Log messages
	Chapter 86. Log messages

Type the following command to display the System Log:

[15:41:54] ABILIS_CPX:d l

Current Local Time: Tuesday 22/08/2017 15:14:40 (UTC+2.00)

03/08/2017 07:27:52 [00103] -------------------- NEW RUN --------------------
03/08/2017 07:27:52 [00509] I: LAST RUN ENDED 03/08/2017 07:27:18 (+00..30s)
03/08/2017 07:27:52 [00398] I: ABILIS CPX Ver. 8.5.1/STD - Build 4238.7
03/08/2017 07:27:52 [00079] I: USING RECONSTRUCTED MP TABLES
03/08/2017 07:27:52 [00079] I: USING 2 CPUs
03/08/2017 07:27:52 [00474] I: CPU clock 1796 MHz
03/08/2017 07:27:52 [00079] W: PCIDEV 8086/1E01 NOT compatible with PIO32
03/08/2017 07:27:52 [00079] W: PIO32 disabled for SATA disks
03/08/2017 07:27:54 [00362] I: WATCHDOG MFLPT-2/3 FW Rev. 17
03/08/2017 07:27:54 [00459] I: ABILIS-ID:1800310
03/08/2017 07:27:54 [00163] I: SYSTEM RESET
03/08/2017 07:27:55 [00195] I: CHKDSK C: OK
03/08/2017 07:27:55 [00371] I: LICENCE, LOADED
03/08/2017 07:27:55 [00024] CONF:MISSING BCK
03/08/2017 07:27:55 [00062] CONF:BACKUP
03/08/2017 07:27:56 [00249] I: USB PCI26/0 EHCI F7F07000 16
03/08/2017 07:27:56 [00249] I: USB PCI29/0 EHCI F7F06000 23
03/08/2017 07:28:00 [00079] BSE-1 ELTI-1 ST:dn
03/08/2017 07:28:01 [00242] I: BSE-1 DSP:0 DWNL OK
03/08/2017 07:28:01 [00079] BSE-1 ELTI-1 ST:init
03/08/2017 07:28:01 [00079] BSE-1 ELTI-1 ST:dn
03/08/2017 07:28:02 [00079] BSE-1 ELTI-1 ST:init
03/08/2017 07:28:04 [00071] TRACE ACTIVATED
03/08/2017 07:28:04 [00291] I: DSP test start
03/08/2017 07:28:04 [00079] BSE-1 ELTI-1 ST:UP
03/08/2017 07:28:05 [00292] I: DSP test end
03/08/2017 07:28:05 [00286] I: CTIR ENABLED
03/08/2017 07:28:05 [00055] SYSTEM STARTED
03/08/2017 07:28:05 [00058] CONF:ACCEPTED
03/08/2017 07:28:05 [00091] I: Pad-1 L1-ST:dn DCD:dn DTR:UP
03/08/2017 07:28:05 [00270] I: Ip-2 ST:gU LINK:LR
03/08/2017 07:28:05 [00270] I: Ip-3 ST:DN LINK:ld
03/08/2017 07:28:05 [00270] I: Ip-4 ST:DN LINK:ld
03/08/2017 07:28:05 [00270] I: Ip-5 ST:DN LINK:ld
03/08/2017 07:28:05 [00270] I: Ip-7 ST:gU LINK:LR
03/08/2017 07:28:05 [00426] I: Telnet-1 ST:RD
03/08/2017 07:28:05 [00411] I: Nat-1 ST:RD
03/08/2017 07:28:05 [00427] I: Ssh-1 ST:RD
03/08/2017 07:28:05 [00345] I: Dhcp-1 ST:RD
03/08/2017 07:28:05 [00180] I: CtiP-31 L1-ST:dn
03/08/2017 07:28:05 [00182] I: CtiP-31 SapiX25:in
03/08/2017 07:28:05 [00180] I: CtiP-32 L1-ST:dn
03/08/2017 07:28:05 [00182] I: CtiP-32 SapiX25:in
03/08/2017 07:28:05 [00267] I: CtiP-501 VOICE-ST:dn PDN-ST:dn SMS-ST:dn
03/08/2017 07:28:05 [00095] I: Eth-1 ST:RD
03/08/2017 07:28:05 [00090] I: X25-999 Layer3:down
03/08/2017 07:28:05 [00089] I: X25-999 Layer2:cg  
03/08/2017 07:28:05 [00092] I: X25-999 PLink:ln SLink:RD
03/08/2017 07:28:05 [00092] I: Ip-3 PLink:d1 SLink:ln
03/08/2017 07:28:05 [00092] I: Pv-1 PLink:d1 SLink:ln
03/08/2017 07:28:05 [00406] I: Trfa-1 ST:RD
03/08/2017 07:28:05 [00092] I: Pv-2 PLink:d1 SLink:ln
03/08/2017 07:28:05 [00092] I: Pv-3 PLink:d1 SLink:ln
03/08/2017 07:28:05 [00092] I: Pv-4 PLink:d1 SLink:ln
03/08/2017 07:28:05 [00095] I: EthUsb-2 ST:NG
03/08/2017 07:28:05 [00346] I: DhcpC-1 ST:RD
03/08/2017 07:28:05 [00231] I: IpSec-1 ST:RD
03/08/2017 07:28:05 [00232] I: Ike-1 ST:RD/RD
03/08/2017 07:28:05 [00092] I: Ip-4 PLink:d1 SLink:ln
03/08/2017 07:28:05 [00092] I: Ip-5 PLink:d1 SLink:ln
03/08/2017 07:28:05 [00461] I: NPv-1 ST:UP
03/08/2017 07:28:05 [00462] I: NPvl-1    P1:dn P2:dn B:-  B-C:- 
03/08/2017 07:28:05 [00462] I: NPvl-5    P1:dn P2:dn B:-  B-C:- 
03/08/2017 07:28:05 [00462] I: NPvl-6    P1:dn P2:-  B:-  B-C:- 
03/08/2017 07:28:05 [00462] I: NPvl-7    P1:dn P2:-  B:-  B-C:- 
03/08/2017 07:28:05 [00092] I: Ip-13 PLink:d1 SLink:ln
03/08/2017 07:28:05 [00020] W: EVENTS LOST
03/08/2017 07:28:06 [00107] AUTO SAVE OK
03/08/2017 07:28:09 [00270] I: Ip-2 ST:UP LINK:LR
03/08/2017 07:28:09 [00270] I: Ip-7 ST:UP LINK:LR
03/08/2017 07:28:10 [00092] I: Ip-13 PLink:d2 SLink:ln
03/08/2017 07:28:13 [00092] I: Pv-1 PLink:d2 SLink:ln
03/08/2017 07:28:13 [00092] I: Pv-2 PLink:d2 SLink:ln
03/08/2017 07:28:13 [00092] I: Ip-4 PLink:d2 SLink:ln
03/08/2017 07:28:29 [00092] I: Ip-13 PLink:RD SLink:ln
03/08/2017 07:28:31 [00092] I: Pv-1 PLink:RD SLink:ln
03/08/2017 07:28:31 [00092] I: Pv-2 PLink:RD SLink:ln
03/08/2017 07:29:25 [00092] I: Ip-3 PLink:d2 SLink:ln
03/08/2017 07:29:26 [00092] I: Ip-5 PLink:d2 SLink:ln
03/08/2017 07:29:26 [00462] I: NPvl-5    P1:dn P2:UP B:-  B-C:- 
03/08/2017 07:29:28 [00462] I: NPvl-1    P1:UP P2:dn B:-  B-C:- 
03/08/2017 07:29:30 [00462] I: NPvl-5    P1:UP P2:UP B:-  B-C:- 
03/08/2017 07:29:43 [00092] I: Ip-3 PLink:RD SLink:ln
03/08/2017 07:29:43 [00092] I: Ip-4 PLink:RD SLink:ln
03/08/2017 07:29:47 [00092] I: Ip-5 PLink:RD SLink:ln
03/08/2017 07:29:49 [00270] I: Ip-3 ST:UP LINK:LR
03/08/2017 07:29:49 [00270] I: Ip-4 ST:UP LINK:LR
03/08/2017 07:29:52 [00270] I: Ip-5 ST:UP LINK:LR

Tip

	Tip
This command allows to display a log file of another version: [09:22:13] ABILIS_CPX:`d l ?` D L [ver] [dd/mm/yyyy] [hh:mm:ss] [LAST:val] [F:val] Display System Log <ver> String corresponding to a version directory in <Optional> the form [x.y.z or x-y-z or y.z or y-z or y]. (E.g. 5.3.1 or 6-1-0 or 2189). dd/mm/yyyy Starting date <Optional> hh:mm:ss Starting time <Optional> LAST: Select the display staring position [RUN, 1..999]: <Optional> - LAST:RUN display only events logged in the last run plus five events of the previous run (if any). - LAST:nnn display last 'nnn' events, where 'nnn' range is [1..999]. F: Filtering string. Case-insensitive match. <Optional> Scan the message for the occurrence of the given substring. Max 70 chars. Spaces require double quotes (E.g. "aaa bbb"). [15:17:50] AAD_MOLD_UFF:_`d l 8-5-0` Current Local Time: Tuesday 22/08/2017 15:17:58 (UTC+2.00) 27/07/2017 16:51:30 [00103] -------------------- NEW RUN -------------------- 27/07/2017 16:51:30 [00509] I: LAST RUN ENDED 27/07/2017 16:50:50 (+00..30s) 27/07/2017 16:51:30 [00398] I: ABILIS CPX Ver. 8.5.0/STD - Build 4238.4 27/07/2017 16:51:30 [00079] I: USING RECONSTRUCTED MP TABLES 27/07/2017 16:51:30 [00079] I: USING 2 CPUs 27/07/2017 16:51:30 [00474] I: CPU clock 1796 MHz 27/07/2017 16:51:30 [00079] W: PCIDEV 8086/1E01 NOT compatible with PIO32 27/07/2017 16:51:30 [00079] W: PIO32 disabled for SATA disks 27/07/2017 16:51:32 [00362] I: WATCHDOG MFLPT-2/3 FW Rev. 17 27/07/2017 16:51:32 [00459] I: ABILIS-ID:1800310 27/07/2017 16:51:32 [00163] I: SYSTEM RESET 27/07/2017 16:51:34 [00195] I: CHKDSK C: OK 27/07/2017 16:51:34 [00371] I: LICENCE, LOADED 27/07/2017 16:51:34 [00249] I: USB PCI26/0 EHCI F7F07000 16 27/07/2017 16:51:34 [00249] I: USB PCI29/0 EHCI F7F06000 23 27/07/2017 16:51:38 [00079] BSE-1 ELTI-1 ST:dn 27/07/2017 16:51:39 [00242] I: BSE-1 DSP:0 DWNL OK 27/07/2017 16:51:39 [00079] BSE-1 ELTI-1 ST:init 27/07/2017 16:51:39 [00079] BSE-1 ELTI-1 ST:dn 27/07/2017 16:51:40 [00079] BSE-1 ELTI-1 ST:init 27/07/2017 16:51:42 [00071] TRACE ACTIVATED 27/07/2017 16:51:42 [00291] I: DSP test start 27/07/2017 16:51:42 [00079] BSE-1 ELTI-1 ST:UP 27/07/2017 16:51:43 [00292] I: DSP test end 27/07/2017 16:51:43 [00286] I: CTIR ENABLED 27/07/2017 16:51:43 [00055] SYSTEM STARTED 27/07/2017 16:51:43 [00104] AUTO SAVE IN PROGRESS 27/07/2017 16:51:43 [00091] I: Pad-1 L1-ST:dn DCD:dn DTR:UP 27/07/2017 16:51:43 [00270] I: Ip-2 ST:gU LINK:LR 27/07/2017 16:51:43 [00270] I: Ip-3 ST:DN LINK:ld 27/07/2017 16:51:43 [00270] I: Ip-4 ST:DN LINK:ld 27/07/2017 16:51:43 [00270] I: Ip-5 ST:DN LINK:ld 27/07/2017 16:51:43 [00270] I: Ip-7 ST:gU LINK:LR 27/07/2017 16:51:43 [00426] I: Telnet-1 ST:RD 27/07/2017 16:51:43 [00411] I: Nat-1 ST:RD 27/07/2017 16:51:43 [00427] I: Ssh-1 ST:RD 27/07/2017 16:51:43 [00345] I: Dhcp-1 ST:RD 27/07/2017 16:51:43 [00180] I: CtiP-31 L1-ST:dn 27/07/2017 16:51:43 [00182] I: CtiP-31 SapiX25:in 27/07/2017 16:51:43 [00180] I: CtiP-32 L1-ST:dn 27/07/2017 16:51:43 [00182] I: CtiP-32 SapiX25:in 27/07/2017 16:51:43 [00267] I: CtiP-501 VOICE-ST:dn PDN-ST:dn SMS-ST:dn 27/07/2017 16:51:43 [00095] I: Eth-1 ST:RD 27/07/2017 16:51:43 [00090] I: X25-999 Layer3:down 27/07/2017 16:51:43 [00089] I: X25-999 Layer2:cg 27/07/2017 16:51:43 [00092] I: X25-999 PLink:ln SLink:RD 27/07/2017 16:51:43 [00092] I: Ip-3 PLink:d1 SLink:ln 27/07/2017 16:51:43 [00092] I: Pv-1 PLink:d1 SLink:ln 27/07/2017 16:51:43 [00406] I: Trfa-1 ST:RD 27/07/2017 16:51:43 [00092] I: Pv-2 PLink:d1 SLink:ln 27/07/2017 16:51:43 [00092] I: Pv-3 PLink:d1 SLink:ln 27/07/2017 16:51:43 [00092] I: Pv-4 PLink:d1 SLink:ln 27/07/2017 16:51:43 [00095] I: EthUsb-2 ST:NG 27/07/2017 16:51:43 [00346] I: DhcpC-1 ST:RD 27/07/2017 16:51:43 [00231] I: IpSec-1 ST:RD 27/07/2017 16:51:43 [00232] I: Ike-1 ST:RD/RD 27/07/2017 16:51:43 [00092] I: Ip-4 PLink:d1 SLink:ln 27/07/2017 16:51:43 [00092] I: Ip-5 PLink:d1 SLink:ln 27/07/2017 16:51:43 [00461] I: NPv-1 ST:UP 27/07/2017 16:51:43 [00462] I: NPvl-1 P1:dn P2:dn B:- B-C:- 27/07/2017 16:51:43 [00462] I: NPvl-5 P1:dn P2:dn B:- B-C:- 27/07/2017 16:51:43 [00462] I: NPvl-6 P1:dn P2:- B:- B-C:- 27/07/2017 16:51:43 [00462] I: NPvl-7 P1:dn P2:- B:- B-C:- 27/07/2017 16:51:43 [00092] I: Ip-13 PLink:d1 SLink:ln 27/07/2017 16:51:43 [00020] W: EVENTS LOST 27/07/2017 16:51:47 [00270] I: Ip-2 ST:UP LINK:LR 27/07/2017 16:51:47 [00270] I: Ip-7 ST:UP LINK:LR 27/07/2017 16:51:48 [00092] I: Ip-13 PLink:d2 SLink:ln 27/07/2017 16:51:51 [00092] I: Pv-1 PLink:d2 SLink:ln 27/07/2017 16:51:51 [00092] I: Pv-2 PLink:d2 SLink:ln 27/07/2017 16:51:51 [00092] I: Ip-4 PLink:d2 SLink:ln 27/07/2017 16:52:06 [00092] I: Ip-13 PLink:RD SLink:ln 27/07/2017 16:52:09 [00092] I: Pv-1 PLink:RD SLink:ln 27/07/2017 16:52:09 [00092] I: Pv-2 PLink:RD SLink:ln 27/07/2017 16:52:39 [00095] I: Eth-2 ST:NG 27/07/2017 16:52:41 [00095] I: Eth-2 ST:RD 27/07/2017 16:52:45 [00092] I: Ip-5 PLink:d2 SLink:ln 27/07/2017 16:52:46 [00092] I: Ip-3 PLink:d2 SLink:ln 27/07/2017 16:52:49 [00462] I: NPvl-5 P1:UP P2:dn B:- B-C:- 27/07/2017 16:52:54 [00462] I: NPvl-5 P1:UP P2:UP B:- B-C:- 27/07/2017 16:52:57 [00462] I: NPvl-1 P1:UP P2:dn B:- B-C:- 27/07/2017 16:53:05 [00092] I: Ip-3 PLink:RD SLink:ln 27/07/2017 16:53:05 [00092] I: Ip-4 PLink:RD SLink:ln 27/07/2017 16:53:10 [00092] I: Ip-5 PLink:RD SLink:ln 27/07/2017 16:53:10 [00270] I: Ip-3 ST:UP LINK:LR 27/07/2017 16:53:10 [00270] I: Ip-4 ST:UP LINK:LR 27/07/2017 16:53:15 [00270] I: Ip-5 ST:UP LINK:LR

This command allows to display a log file of another version:

[09:22:13] ABILIS_CPX:d l ?

D L [ver] [dd/mm/yyyy] [hh:mm:ss] [LAST:val] [F:val]    Display System Log

<ver>          String corresponding to a version directory in       <Optional> 
               the form [x.y.z or x-y-z or y.z or y-z or y].
               (E.g. 5.3.1 or 6-1-0 or 2189).
dd/mm/yyyy      Starting date                                       <Optional>
hh:mm:ss        Starting time                                       <Optional>
LAST:           Select the display staring position [RUN, 1..999]:  <Optional>
                - LAST:RUN display only events logged in the last run
                  plus five events of the previous run (if any).
                - LAST:nnn display last 'nnn' events, where 'nnn' range
                  is [1..999].
F:              Filtering string. Case-insensitive match.           <Optional>
                Scan the message for the occurrence of the given substring.
                Max 70 chars. Spaces require double quotes (E.g. "aaa bbb").

[15:17:50] AAD_MOLD_UFF:_d l 8-5-0           

Current Local Time: Tuesday 22/08/2017 15:17:58 (UTC+2.00)

27/07/2017 16:51:30 [00103] -------------------- NEW RUN --------------------
27/07/2017 16:51:30 [00509] I: LAST RUN ENDED 27/07/2017 16:50:50 (+00..30s)
27/07/2017 16:51:30 [00398] I: ABILIS CPX Ver. 8.5.0/STD - Build 4238.4
27/07/2017 16:51:30 [00079] I: USING RECONSTRUCTED MP TABLES
27/07/2017 16:51:30 [00079] I: USING 2 CPUs
27/07/2017 16:51:30 [00474] I: CPU clock 1796 MHz
27/07/2017 16:51:30 [00079] W: PCIDEV 8086/1E01 NOT compatible with PIO32
27/07/2017 16:51:30 [00079] W: PIO32 disabled for SATA disks
27/07/2017 16:51:32 [00362] I: WATCHDOG MFLPT-2/3 FW Rev. 17
27/07/2017 16:51:32 [00459] I: ABILIS-ID:1800310
27/07/2017 16:51:32 [00163] I: SYSTEM RESET
27/07/2017 16:51:34 [00195] I: CHKDSK C: OK
27/07/2017 16:51:34 [00371] I: LICENCE, LOADED
27/07/2017 16:51:34 [00249] I: USB PCI26/0 EHCI F7F07000 16
27/07/2017 16:51:34 [00249] I: USB PCI29/0 EHCI F7F06000 23
27/07/2017 16:51:38 [00079] BSE-1 ELTI-1 ST:dn
27/07/2017 16:51:39 [00242] I: BSE-1 DSP:0 DWNL OK
27/07/2017 16:51:39 [00079] BSE-1 ELTI-1 ST:init
27/07/2017 16:51:39 [00079] BSE-1 ELTI-1 ST:dn
27/07/2017 16:51:40 [00079] BSE-1 ELTI-1 ST:init
27/07/2017 16:51:42 [00071] TRACE ACTIVATED
27/07/2017 16:51:42 [00291] I: DSP test start
27/07/2017 16:51:42 [00079] BSE-1 ELTI-1 ST:UP
27/07/2017 16:51:43 [00292] I: DSP test end
27/07/2017 16:51:43 [00286] I: CTIR ENABLED
27/07/2017 16:51:43 [00055] SYSTEM STARTED
27/07/2017 16:51:43 [00104] AUTO SAVE IN PROGRESS
27/07/2017 16:51:43 [00091] I: Pad-1 L1-ST:dn DCD:dn DTR:UP
27/07/2017 16:51:43 [00270] I: Ip-2 ST:gU LINK:LR
27/07/2017 16:51:43 [00270] I: Ip-3 ST:DN LINK:ld
27/07/2017 16:51:43 [00270] I: Ip-4 ST:DN LINK:ld
27/07/2017 16:51:43 [00270] I: Ip-5 ST:DN LINK:ld
27/07/2017 16:51:43 [00270] I: Ip-7 ST:gU LINK:LR
27/07/2017 16:51:43 [00426] I: Telnet-1 ST:RD
27/07/2017 16:51:43 [00411] I: Nat-1 ST:RD
27/07/2017 16:51:43 [00427] I: Ssh-1 ST:RD
27/07/2017 16:51:43 [00345] I: Dhcp-1 ST:RD
27/07/2017 16:51:43 [00180] I: CtiP-31 L1-ST:dn
27/07/2017 16:51:43 [00182] I: CtiP-31 SapiX25:in
27/07/2017 16:51:43 [00180] I: CtiP-32 L1-ST:dn
27/07/2017 16:51:43 [00182] I: CtiP-32 SapiX25:in
27/07/2017 16:51:43 [00267] I: CtiP-501 VOICE-ST:dn PDN-ST:dn SMS-ST:dn
27/07/2017 16:51:43 [00095] I: Eth-1 ST:RD
27/07/2017 16:51:43 [00090] I: X25-999 Layer3:down
27/07/2017 16:51:43 [00089] I: X25-999 Layer2:cg  
27/07/2017 16:51:43 [00092] I: X25-999 PLink:ln SLink:RD
27/07/2017 16:51:43 [00092] I: Ip-3 PLink:d1 SLink:ln
27/07/2017 16:51:43 [00092] I: Pv-1 PLink:d1 SLink:ln
27/07/2017 16:51:43 [00406] I: Trfa-1 ST:RD
27/07/2017 16:51:43 [00092] I: Pv-2 PLink:d1 SLink:ln
27/07/2017 16:51:43 [00092] I: Pv-3 PLink:d1 SLink:ln
27/07/2017 16:51:43 [00092] I: Pv-4 PLink:d1 SLink:ln
27/07/2017 16:51:43 [00095] I: EthUsb-2 ST:NG
27/07/2017 16:51:43 [00346] I: DhcpC-1 ST:RD
27/07/2017 16:51:43 [00231] I: IpSec-1 ST:RD
27/07/2017 16:51:43 [00232] I: Ike-1 ST:RD/RD
27/07/2017 16:51:43 [00092] I: Ip-4 PLink:d1 SLink:ln
27/07/2017 16:51:43 [00092] I: Ip-5 PLink:d1 SLink:ln
27/07/2017 16:51:43 [00461] I: NPv-1 ST:UP
27/07/2017 16:51:43 [00462] I: NPvl-1    P1:dn P2:dn B:-  B-C:- 
27/07/2017 16:51:43 [00462] I: NPvl-5    P1:dn P2:dn B:-  B-C:- 
27/07/2017 16:51:43 [00462] I: NPvl-6    P1:dn P2:-  B:-  B-C:- 
27/07/2017 16:51:43 [00462] I: NPvl-7    P1:dn P2:-  B:-  B-C:- 
27/07/2017 16:51:43 [00092] I: Ip-13 PLink:d1 SLink:ln
27/07/2017 16:51:43 [00020] W: EVENTS LOST
27/07/2017 16:51:47 [00270] I: Ip-2 ST:UP LINK:LR
27/07/2017 16:51:47 [00270] I: Ip-7 ST:UP LINK:LR
27/07/2017 16:51:48 [00092] I: Ip-13 PLink:d2 SLink:ln
27/07/2017 16:51:51 [00092] I: Pv-1 PLink:d2 SLink:ln
27/07/2017 16:51:51 [00092] I: Pv-2 PLink:d2 SLink:ln
27/07/2017 16:51:51 [00092] I: Ip-4 PLink:d2 SLink:ln
27/07/2017 16:52:06 [00092] I: Ip-13 PLink:RD SLink:ln
27/07/2017 16:52:09 [00092] I: Pv-1 PLink:RD SLink:ln
27/07/2017 16:52:09 [00092] I: Pv-2 PLink:RD SLink:ln
27/07/2017 16:52:39 [00095] I: Eth-2 ST:NG
27/07/2017 16:52:41 [00095] I: Eth-2 ST:RD
27/07/2017 16:52:45 [00092] I: Ip-5 PLink:d2 SLink:ln
27/07/2017 16:52:46 [00092] I: Ip-3 PLink:d2 SLink:ln
27/07/2017 16:52:49 [00462] I: NPvl-5    P1:UP P2:dn B:-  B-C:- 
27/07/2017 16:52:54 [00462] I: NPvl-5    P1:UP P2:UP B:-  B-C:- 
27/07/2017 16:52:57 [00462] I: NPvl-1    P1:UP P2:dn B:-  B-C:- 
27/07/2017 16:53:05 [00092] I: Ip-3 PLink:RD SLink:ln
27/07/2017 16:53:05 [00092] I: Ip-4 PLink:RD SLink:ln
27/07/2017 16:53:10 [00092] I: Ip-5 PLink:RD SLink:ln
27/07/2017 16:53:10 [00270] I: Ip-3 ST:UP LINK:LR
27/07/2017 16:53:10 [00270] I: Ip-4 ST:UP LINK:LR
27/07/2017 16:53:15 [00270] I: Ip-5 ST:UP LINK:LR

Notification messages are stored in the Abilis CPX System Log file in the following format:

Table 86.1. System Log event's format

Date	Time	Event Code	Event Text
dd/mm/yyyy	hh:mm:ss	[nnnnn]	Textual message

Notification messages are classified on the basis of the importance of the reported event. The event importance is indicated by a prefix reported in the text of the event message itself.

The following table lists Event types and the corresponding Event text prefix:

Table 86.2. System Log event's classification

Event type	Event text prefix	Meaning
Unclassified	none	Indications of general events.
Error	E:	Notifications of critical errors which require the reset of Abilis CPX. All the sessions are closed and Abilis CPX automatically restarts. Note that an exception is generated and saved in the Exceptions Log for a possible use by Abilis engineers.
Warning	W:	Notifications of not critical events that could be caused by some malfunction. The reason must be carefully identified, but the system will continue to function.
Informative	I:	Notifications of events of particular interest that occur in the regular system operation.

Each message also has a Severity level indicator, based on SYSLOG protocol severity classification. See SYSLOG section for a description of SYSLOG Message Severities.

Table 86.3. System Log event's List

Event code	Severity	Event Text	Meaning
00020	WARNING	W: EVENTS LOST	Events has been lost because the system wasn't able to write all of them in the log file. Usually this event could appears at system start-up when many events are generated at the same time.
00021	INFO	<message string>	This event is used to signal high priority messages, that could be meaningless for the user, but that is very useful for the Abilis CPX technicians for solving eventual problems.
00022	INFO	CONF:MISSING CFG	The configuration file `drivers.cfg` is missing.
00023	INFO	CONF:LOAD BCK	Abilis CPX is loading the configuration backup file `drivers.bck`, because configuration file `drivers.cfg` is missing or not valid.
00024	INFO	CONF:MISSING BCK	The configuration backup file `drivers.bck` is missing.
00025	INFO	CONF:CORRUPTED	Error in the content, or in the format of configuration file `drivers.cfg`.
00026	INFO	CONF:INVALID BCK	Error in the content, or in the format of configuration backup file `drivers.bck`.
00027	ERROR	E: DEBUG LOG Err:xx	Error in Debug Log Service. 'xx' is the error code to be reported to the Abilis CPX Help desk.
00028	ERROR	E: E00	The System exit because Esc or Alt/X key was pressed by the user.
00029	ERROR	E: PO1	Software exception of type 01. Note that software exceptions are generated and saved in the Exceptions Log for a possible use by Abilis engineers.
00030	ERROR	E: PO2	Software exception of type 02. Note that software exceptions are generated and saved in the Exceptions Log for a possible use by Abilis engineers.
00031	ERROR	E: PO3	Software exception of type 03. Note that software exceptions are generated and saved in the Exceptions Log for a possible use by Abilis engineers.
00032	INFO	AUTO WARM START	Automatic restart of Abilis CPX usually caused by an error.
00033	INFO	WARM START	A request for unconditional system restart has been submitted by the user, through the WARM START command.
00034	INFO	RESTART SYSTEM	A request for system restart has been submitted by the user through the RESTART SYSTEM command. The RESTART SYSTEM can be either issued to the command interpreter of the CP (Control Port) resource or executed from the Abilis CPX frontal panel.
00035	ERROR	E: C01	Error in the DCP Service (i.e. The data compression/expansion service) during allocation of data compression/expansion buffers.
00036	ERROR	E: Mdd	Error in memory allocation phase. 'dd' is the error code to be reported to the Abilis CPX Help desk.
00037	ERROR	E: Mxx yy	Error in memory allocation phase. 'xx' and 'yy' are the error code and sub-code to be reported to the Abilis CPX Help Desk.
00038	ERROR	E: Nxx yy ddd zz	Error in the Ncb exchange between two drivers. 'xx' represents the hexadecimal value of the driver's return code; 'yy' represents the hexadecimal code of the command which has caused the warning; 'ddd' represents the driver's port number; 'zz' represents and additional code whose usage is intended for Abilis engineers only.
00039	ERROR	E: D00 xxxx	Software driver error of type 00. 'xxxx' is the error sub-code that must be reported to the Abilis CPX Help Desk.
00040	ERROR	E: D01 xx yy	Software driver error of type 01. 'xx' and 'yy' are the error code and sub-code to be reported to the Abilis CPX Help Desk.
00041	ERROR	E: D02 xx	Software driver error of type 02. 'xx' is the error sub-code that must be reported to the Abilis CPX Help Desk.
00042	ERROR	E: D03	Software driver error of type 03; it must be reported to the Abilis CPX Help Desk.
00043	ERROR	E: B01 xxxx	The Configuration Service detected that a mandatory configuration block is missing. 'xxxx' is the exadecimal code that identifies the configuration block.
00044	ERROR	E: B02 xxxx	The Configuration Service detected that a configuration block is corrupted. 'xxxx' is the hexadecimal code that identifies the configuration block.
00045	ERROR	E: Xxx	Software error in “exit” function installation. “xx” is the hexadecimal code that identifies the software function for which the error is generated and that must be reported to the Abilis CPX Help Desk.
00046	ERROR	E: GSxx	Error in Global Submit Service. 'xx' is the hexadecimal code that identifies the error and that must be reported to the Abilis CPX Help Desk.
00047	ERROR	E: Gxx yyyy	Generic software errors. 'xx' and 'yy' are the error code and sub-code to be reported to the Abilis CPX Help Desk.
00048	ERROR	E: Axx yy ddd	Severe error in the Ncb exchange between two drivers. 'xx' represents the hexadecimal value of the driver's return code; 'yy' represents the hexadecimal code of the command which has caused the warning; 'ddd' represents the driver's port number.
00049	INFO	TIMEOUT EXIT	System exit loop timed out.
00050	ERROR	E: Txx	Error in Terminator Service. 'xx' is the hexadecimal code that identifies the error and that must be reported to the Abilis CPX Help Desk.
00051	INFO	PNP REBOOT	Automatic restart of Abilis CPX caused by the PNP/PCI manager.
00052	INFO	ALARMED RESOURCEs	Indicates that there are alarmed resources.
00053	ERROR	E: OS EXIT	Severe error at operating system level. It's often caused by defective or extremely low amount of system RAM. If the problem persist after replacing or increasing the amount the system RAM, contact Abilis CPX technical assistance.
00054	INFO	<message string>	This event is used to signal low priority messages, that could be meaningless for the user, but that is useful for the Abilis CPX technicians for detecting problems.
00055	INFO	SYSTEM STARTED	The initialization phases of the system is complete and then system is active.
00056	WARNING	I: WATCHDOG LIVE1	The system watchdog (WDG) detected that in the previous run CPX was restarted because of Live signal 1.
00057	WARNING	I: WATCHDOG LIVE2	The system watchdog (WDG) detected that in the previous run CPX was restarted because of Live signal 2.
00058	INFO	CONF:ACCEPTED	The previously saved main configuration has been checked and accepted as valid because the system was able to successfully start with it. Main configuration is stored in `drivers.cfg` file, backup configuration in `drivers.bck` file.
00059	INFO	CONF:REFUSED	The state of configuration file drivers.cfg isn't valid (i.e. Equal to 2 or 4).
00060	INFO	CONF:RESTORE	The system is going to restore configuration backup file `drivers.bck` to configuration file `drivers.cfg`.
00061	INFO	CONF:RESTORE ERR	Error while the system was restored configuration backup file `drivers.bck` to configuration file `drivers.cfg`.
00062	INFO	CONF:BACKUP	This event indicates that a backup copy of the main configuration has been created. Usually it occurs after the System Log event 00058.
00063	INFO	CONF:BACKUP ERR	Error while the system was creating a backup copy of the configuration file `drivers.cfg` into the backup configuration file '`drivers.bck`.
00064	WARNING	W: C03 dd	This event is generated by the DCP Service (i.e. The data compression/expansion service) to inform that only a sub-set of the dictionaries is available. Usually this is caused by an insufficient system memory. 'dd' is the number of dictionaries that are currently available in the system.
00065	WARNING	W: C02	This event is generated by the DCP Service (i.e. The data compression/expansion service) to inform that no dictionaries are available. By consequence the data compression isn't available. Usually this is caused by an insufficient system memory.
00066	WARNING	W: C04 D:xx R:yy	This event is used to signal that the DCP Service (i.e. The data compression/expansion service) initialization fails. 'xx' is the hexadecimal code that identifies a dictionary; 'yy' is the hexadecimal code that identifies that the error must be reported to the Abilis CPX Help Desk.
00067	INFO	SAVING DEBUG LOG	Debug Log is going to be saved into the `cpx.dbg` file.
00068	INFO	DEBUG LOG SAVED	Debug Log was successfully saved into the file `cpx.dbg`.
00069	INFO	DEBUG LOG ERROR	Debug Log wasn't saved into the file `cpx.dbg`, because it was empty.
00070	INFO	DEBUG LOG ERROR	Debug Log wasn't saved into `cpx.dbg` file, because an error occurred.
00071	INFO	TRACE ACTIVATED	Ncb Trace activated at system start up. This event signals that the function for tracing internal events has been automatically activated at the system start-up.
00072	INFO	TRACE NOT ACTIVE	Ncb Trace not activated because an error occurred. This event signals that it wasn't possible to activate the tracing of internal events at the system start-up.
00073	WARNING	W: Axx yy ddd	Ncb management error. Error in the Ncb exchange between two drivers. It must be reported to the Abilis CPX Help desk. 'xx' represents the hexadecimal value of the driver's return code; 'yy' represents the hexadecimal code of the command which has caused the warning; 'ddd' represents the driver's port number.
00074	WARNING	W: L94	Error in the length of the data part of the Ncb exchanged between two drivers, that must be reported to the Abilis CPX Help desk. This event is usually followed by the System Log event 00075.
00075	WARNING	xxxx LSN:yy P:ddd	Error in the length of the data part of the Ncb exchanged between two drivers, that must be reported to the Abilis CPX Help desk. This event is always preceded by the System Log event 00074. 'xxxx' is the hexadecimal value of the length of data part; 'yy' represents the hexadecimal code of the command which has caused the warning; 'ddd' represents the driver's port number.
00076	INFO	MAIN_STACK SIZE < 2500 BYTES	The Main thread stack is less than 2500 bytes.
00077	INFO	I: Sim-nnn Lsn:xx CONNECTED	This event is generated by the SIM (Simulator) resource to signal a connection establishment. 'nnn' is the resource identifier; 'xx' is the connection identifier.
00078	INFO	I: Sim-nnn Lsn:xx DISCONNECTED	This event is generated by the SIM (Simulator) resource to signal a connection closing. 'nnn' is the resource identifier; 'xx' is the connection identifier.
00079	INFO	<message string>	This event is used by software drivers to write generic messages in the System Log file. Usually this message is meaningless for the user, but they could be useful for Abilis engineers for SW debugging.
00080	INFO	DPMI MEMORY STATISTICs N/A	DPMI memory status check function fails.
00081	WARNING	W: C05	DCP Service (i.e. The data compression/expansion service) has been reinitialized.
00082	WARNING	W: RC:xx NCB:yy Type-nnn (ddd)	Unexpected return code in the Ncb exchange between two drivers. It must be reported to the Abilis CPX Help desk. 'xx' represents the hexadecimal value of the driver's return code; 'yy' represents the hexadecimal code of the command which has caused the warning; 'Type-nnn' are the driver's resource type and identifier; 'ddd' is the driver's port number.
00083	WARNING	W: WATCHDOG START	The system watchdog (WDG) detected that in the previous run the CPX boot phase was timed-out.
00084	ERROR	E: HWINT ERROR	Hardware interfaces (system watchdog (WDG), Front panel, LCD, etc) initialization fails.
00085	WARNING	W: ALARM SETTED	An alarm is on.
00086	W: ALARM RESET	The ALARM RESET command has been issued.
00087	INFO	I: Sim-nnn CAUSE: F1,xx	This event is generated by the SIM (Simulator) resource to inform about a connection closing cause. 'nnn' is the resource identifier; 'F1,xx' are the connection close cause and diagnostic codes.
00088	INFO	I: Sync-nnn ST:s1 DCD:s2 DTR:s3	Diagnostic information about a Synchronous resource; 'nnn' is the resource identifier; 's1' is the Layer 1 state [down, UP, HT (Halted), FL (failed)]; 's2' is the DCD signal state [dn (down), UP, NA (Not Available)].
00089	INFO	I: X25-nnn Layer2:ssss	Diagnostic information about the Layer 2 (LAPB) of an X.25 resource; 'nnn' is the resource identifier; 'ssss' is the Layer 2 (LAPB) state[down, cg (connecting), CONN (connected), frmr (FRMR), wait (waiting)].
00090	INFO	I: X25-nnn Layer3:ssss	Diagnostic information about the Layer 3 (X.25) of an X.25 resource. 'nnn' is the resource identifier; 'ssss' is the Layer 3 (X.25) state [down, rstg (restarting), rstd (restarted), RDY (ready)].
00091	INFO	I: Pad-nnn L1-ST:s1 DCD:s2 DTR:s3	Diagnostic information about a PAD resource. 'nnn' is the resource identifier; 's1' is the Asynchronous Layer 1 state [down, UP, HT (halted), FL (failed)]; 's2' is the DCD signal state [dn, UP, NA (not-available)]; 's3' is the DTR signal state [dn, UP, NA (not-available)].
00092	INFO	I: Type-nnn PLink:s1 SLink:s2	Diagnostic information about the Link layer (MLM) of a resource. 'Type' is the resource type; 'nnn' is the resource identifier; 's1' is the P-Link state [RD (ready), ln (link not-present), le (link error), d1 (down1) d2 (down2); 's2' is the S-Link state [RD (ready), CN (connected), ln (link not-present), s1 (stopped1), s2 (stopped2)].
00093	INFO	I: Fr-nnn ST:ssss	Diagnostic information about a Frame Relay resource. 'nnn' is the resource identifier; 'ssss' is the resource state [down, L-dn (LMI down) L-UP (LMI), BLND (blind)].
00094	INFO	I: Ip-nnn LAN-ST:ss	Diagnostic information about the LAN layer of an Ip resource. 'nnn' is the resource identifier; 'ss' is the LAN layer state [LD (link down), LR (link ready), LN (link not-present), HD (halted), FD (failed)].
00095	INFO	I: Eth-nnn ST:ss	Diagnostic information about a Fast Ethernet (Ethernet) resource. 'nnn' is the resource identifier; 'ss' is the resource state [DN ( down), RD (ready), TD (tx disabled), HD (halted), FD (failed), NG (negotiating)].
00096	INFO	I: Tr-nnn ST:ss	Diagnostic information about a Token Ring resource. 'nnn' is the resource identifier. 'ss' is the resource state [HR (hw reset), SR (sw reset), TR (tx reset), IG (initializing), ID (initialized), OG (opening), ON (open), CG (closing), CD (closed), DN (down), RD (ready), HD (halted), FD (failed)].
00097	INFO	I: Hdlct-nnn ST:ss	Diagnostic information about an HDLCT resource. 'nnn' is the resource identifier; 'ss' is the resource state [DN (down), RD (ready), ST (stopped), CL (calling), CN (connected), CR (clearing)].
00098	INFO	I: Fr-nnn DLCI:ddddddd ST:ss	Diagnostic information about a DLCI of a Frame Relay resource. 'nnn' is the resource identifier; 'ddddddd' is the DLCI number; 'ss' is the DLCI state [nu (not-used), dn (down). id (idle), np (not-present), AC (active), in (inactive), BL (blind), rm (removed).
00099	INFO	I: Sdlc-nnn PU AD:xx ST:ss	Diagnostic information about a Physical Unit of an Sdlc resource. 'nnn' is the resource identifier; 'xx' is the Physical Unit address; 'ss' is the Physical Unit state [ dn (down), st (stopped), CN (connected)].
00100	INFO	I: Type-nnn PLink:s1 SLink:s2	Diagnostic information about the Multi-Links layer (ML) of a resource. 'Type' is the resource type; 'nnn' is the resource identifier; 's1' is the Global P-Links state[dn (all links are in down state), rd (some links are in ready state), RD (all links are in ready state), np (no links are present)]; 's2' is the Global S-Links state [ s1 (stopped1), RD (ready), np (no links are present)].
00101	INFO	I: Type-nn PL-dd:ss	Diagnostic information about a P-Link of the Multi-Links layer (ML) of a resource. 'Type' is the resource type; 'nnn' is the resource identifier; 'dd' is the P-Link identifier; 'ss' is the P-Link state [dn (down), st (stopped), CN (connected)].
00102	INFO	I: Ip-nnn PPP-ST:ss	Diagnostic information about PPP layer of an Ip resource. 'nnn' is the resource identifier; 'ss' is the PPP layer state [s1 (stopped 1 ), s2 (stopped 2), s3 ( stopped 3), DL (delaying), DN (down), UP (up)].
00103	INFO	-------------------- NEW RUN --------------------	This event indicates the start-up of the system: the software has been loaded and the initialization phase is in progress.
00104	INFO	AUTO SAVE IN PROGRESS	The system has initiated the automatic saving of the current configuration as the main configuration. Main configuration is stored in `drivers.cfg` file, backup configuration in `drivers.bck` file.
00105	INFO	AUTO SAVE ABORTED	The automatic saving of the current configuration has been aborted because of an error. Main configuration is stored in `drivers.cfg` file, backup configuration in `drivers.bck` file.
00106	INFO	AUTO SAVE FAIL	The automatic saving of the current configuration failed because of an error. Main configuration is stored in `drivers.cfg` file, backup configuration in `drivers.bck` file.
00107	INFO	AUTO SAVE OK	The automatic saving of the current configuration was successful. Main configuration is stored in `drivers.cfg` file, backup configuration in `drivers.bck` file.
00108	WARNING	W: Heap Corrupted xx	A corruption of System memory (called 'heap') has been detected. The error can be caused by a software bug or by defective system RAM memory. 'xx' is an hexadecimal code to be reported to the Abilis CPX Help desk.
00109	WARNING	W: Heap Empty xx	System memory (called 'heap') cannot be inspected. The error can be caused by a software bug or by defective system RAM memory. 'xx' is a hexadecimal code to be reported to the Abilis CPX Help desk.
00110	WARNING	W: Heap Check Fail xx	The cyclic check of System memory (called 'heap') could not be completed because it's probably corrupted. The error can be caused by a software bug or by defective system RAM memory. 'xx' is a hexadecimal code to be reported to the Abilis CPX Help desk.
00111	WARNING	W: Heap Register Err01	The markers of a software module cannot be written in the System memory (called 'heap'). The error can be caused by a software bug or by defective system RAM memory.
00112	WARNING	W: PCI MANY CARDs	The maximum limit of 32 PCI cards which the system can support, has been reached. Report the error to the Abilis CPX Help Desk.
00113	WARNING	W: PCI LAST DEVICE PARKING CHIP SET	The chipset present on the mother board is incompatible with CPX software. Report the error to the Abilis CPX Help desk.
00114	WARNING	W: PCI UNKNOWN CHIP SET	The chipset present on the mother board isn't in the list of the known ones. Report the error to the Abilis CPX Help desk.
00115	WARNING	W: PCISRV FAIL	The initialization of the PCI service failed. Report the error to the Abilis CPX Help desk.
00116	WARNING	W: PNP FAIL	The initialization of the PNP service failed. Report the error to the Abilis CPX Help desk.
00117	WARNING	W: PNP REFRESH FAIL	The updating of the PNP service failed. Report the error to the Abilis CPX Help desk.
00118	INFO	I: CP DTR ss RES:Sync-nnn	Execution on a Synchronous resource of the command for setting up the status of the DTR signal. 'ss' is the state of the DTR signal which has been set up [UP (up), DN (down), PL (pulse)]. 'nnn' is the Synchronous resource identifier.
00119	INFO	I: Sdlc-nnn QTEST	Reception by an SDLC resource, of a 'QLLC TEST' notification for activating the control procedure of the DTR signal. 'nnn' is the resource identifier.
00120	INFO	I: Sync-nnn DTR ss	Reception by a Synchronous resource of the command for setting up the status of the DTR signal. 'nnn' is the Synchronous resource identifier; 'ss' is the state of the DTR signal which has been set up [UP (up), DN (down), PL (pulse)].
00121	INFO	I: CHANGE from DST to STD time mode	The system time mode is going to be changed from Daylight Savings time mode to Standard time mode.
00122	INFO	I: CHANGE from DST to STD time mode DONE	The system time mode has been changed from Daylight Savings time mode to Standard time mode.
00123	INFO	I: CHANGE from STD to DST time mode	The system time mode is going to be changed from Standard time mode to Daylight Savings time mode.
00124	INFO	I: CHANGE from STD to DST time mode DONE	The system time mode has been changed from Standard time mode to Daylight Savings time mode.
00125	INFO	I: TIME UPDATE, Delta > 1 min.(ddddddd sec.)	This event is generated by the system time synchronization service (SNTP): local date and time adjustment is in progress and the time delta, between the local clock and the synchronization Server, is greater than 1 minute. This event is followed by the System Log event 00126. 'ddddddd' is the time delta, between the local clock and the synchronization Server, in second.
00126	INFO	I: TIME UPDATE DONE	This event is generated by the system time synchronization service (SNTP): local date and time adjustment has been executed. This event appears after the System Log event 00125.
00127	WARNING	W: PVC:nn INVALID POINTER	This event is generated by the Connection Oriented Router when it detects invalid setting in PVC structure. Please report the error to the Abilis CPX Help desk. 'nn' is the PVC identifier to be reported to the Abilis CPX Help desk, together with the `drivers.cfg` file.
00128	ERROR	E: HNDL dd	This event is generated by the software when it detects invalid setting in internal data structure. Please report the error to the Abilis CPX Help desk. 'dd' is the data identifier to be reported to the Abilis CPX Help desk, together with the `drivers.cfg` file.
00129	WARNING	W: ACNT dd	Accounting (ACNT) driver's specific warning message. It's the first one of a set of six messages (see System Log events 00130..00134). They're meaningless for the user, but it's useful for Abilis engineers for sw debugging. Please report the event to Abilis CPX Help desk. 'dd' is an internal error code to be reported to the Abilis CPX Help desk, together with the `drivers.cfg` file.
00130	WARNING	STA: dd	Accounting (ACNT) driver's specific warning message. It's the second one of a set of six messages (see System Log events 00129..00134). They're meaningless for the user, but it's useful for Abilis engineers for SW debugging. Please report the event to the Abilis CPX Help desk. 'dd' is an internal error code to be reported to the Abilis CPX Help desk, together with the `drivers.cfg` file.
00131	WARNING	LSN: dd	Accounting (ACNT) driver's specific warning message. It's the third one of a set of six messages (see System Log events 00129..00134). They're meaningless for the user, but it's useful for Abilis engineers for SW debugging. Please report the event to the Abilis CPX Help desk. 'dd' is an internal error code to be reported to the Abilis CPX Help desk, together with the `drivers.cfg` file.
00132	WARNING	MOD: dd	Accounting (ACNT) driver's specific warning message. It's the forth one of a set of six messages (see System Log events 00129..00134). They're meaningless for the user, but it's useful for Abilis engineers for sw debugging. Please report the event to Abilis CPX Help desk. 'dd' is an internal error code to be reported to the Abilis CPX Help desk, together with the `drivers.cfg` file.
00133	WARNING	DRC: dd	Accounting (ACNT) driver's specific warning message. It's the fifth one of a set of six messages (see System Log events 00129..00134). They're meaningless for the user, but it's useful for Abilis engineers for SW debugging. Please report the event to the Abilis CPX Help desk. 'dd' is an internal error code to be reported to the Abilis CPX Help desk, together with the `drivers.cfg` file.
00134	WARNING	COD: dd	Accounting (ACNT) driver's specific warning message. It's the sixth one of a set of six messages (see System Log events 00129..00133). They're meaningless for the user, but it's useful for Abilis engineers for sw debugging. Please report the event to Abilis CPX Help desk. 'dd' is an internal error code to be reported to the Abilis CPX Help desk, together with the `drivers.cfg` file.
00135	ERROR	MEMORY SUMMARY:	Informative message about the state of the system memory. It's the first one of a set of six messages (see System Log events 00136..00140). These messages indicate a possible internal error, please report the event to the Abilis CPX Help desk.
00136	ERROR	TOT: nnn.nnn.nnn	Informative message about the state of the system memory. It's the second one of a set of six messages (see System Log events 00135..00140). These messages indicate a possible internal error, please report the event to the Abilis CPX Help desk. 'nnn.nnn.nnn' is the total system memory size in bytes.
00137	ERROR	FREE:nnn.nnn.nnn	Informative message about the state of the system memory. It's the third one of a set of six messages (see System Log events 00135..00140). These messages indicate a possible internal error, please report the event to the Abilis CPX Help desk. 'nnn.nnn.nnn' is the availble system memory size in bytes.
00138	ERROR	HU: nnn.nnn.nnn	Informative message about the state of the system memory. It's the fourth one of a set of six messages (see System Log events 00135..00140). These messages indicate a possible internal error, please report the event to the Abilis CPX Help desk. 'nnn.nnn.nnn' is the used system memory size in bytes.
00139	ERROR	HLFB:nnn.nnn.nnn	informative message about the state of the system memory. It's the fifth one of a set of six messages (see System Log events 00135..00140). These messages indicate a possible internal error, please report the event to the Abilis CPX Help desk. 'nnn.nnn.nnn' is the size, in bytes, of the biggest block of contiguous system memory that is currently available.
00140	ERROR	HLUB:nnn.nnn.nnn	Informative message about the state of the system memory. It's the last one of a set of six messages (see System Log events 00135..00139). These messages indicate a possible internal error, please report the event to the Abilis CPX Help desk. 'nnn.nnn.nnn' is the size, in bytes, of the biggest block of contiguous system memory that is currently in use.
00141	WARNING	W: Iprtr Table OVERFLOW	The IP Router (Iprtr) routing table reached its maximum capacity.
00142	WARNING	W: Iprtr Table DANGER ON	The IP Router (Iprtr) Routings table going in DANGER state.
00143	WARNING	W: Iprtr Table DANGER OFF	The IP Router (Iprtr) Routings table exiting from DANGER state.
00144	WARNING	W: Rip Table OVERFLOW	The internal routings table of Rip driver reached its maximum capacity.
00145	WARNING	W: Rip Table DANGER ON	The internal routings table of Rip driver entered the DANGER state.
00146	WARNING	W: Rip Table DANGER OFF	The internal routings table of Rip driver exited from the DANGER state.
00147	INFO	ASSERT: Line nn, Parameter dd	This event is used by software drivers to signal unexpected conditions. They could be meaningless for the user, but that is useful for the Abilis CPX technicians for detecting problems. Please report it to the Abilis CPX Help desk. 'nn' is the line number of the file where this event is generated; 'dd' is an addition decimal code to be reported to Abilis CPX technicians.
00148	WARNING	W: FRMWR M:sss L:nnn P:ddd	This event is used by sw drivers to inform about rare conditions. They could be meaningless for the user, but they're useful for the Abilis CPX technicians for detecting problems. Please report it to the Abilis CPX Help desk. 'sss' is an addition string used to identify the origin of the event; 'nnn' is the line number of the file where this event is generated; 'ddd' is an addition decimal code to be reported to Abilis CPX technicians.
00149	INFO	I: Ip-nnn PPP-ST:s1 LINK-ST:s2	This event reports diagnostic information about the PPP layer of an Ip resource. 'nnn' is the resource identifier. 's1' is the PPP layer state [s1 (stopped 1), s2 (stopped 2), s3 (stopped 3), DL (delaying), DN (down), UP (up)]; 's2' is the PPP link state [dn (down), CN (connected)].
00150	WARNING	W: MISSING '<file-name>'	The '<file-name>' file is missing. Please report the event to the Abilis CPX Help desk.
00151	WARNING	W: '<file-name>' Err:xx	An error (whose hexadecimal code is 'xx') occurred during the '<file-name>' file treatment. Please report the event to the Abilis CPX Help desk.
00152	WARNING	W: WATCHDOG NOT FOUND	An error occurred during Hw interface(s) (system watchdog (WDG), Front panel, LCD display, etc) initialization phase.
00153	ERROR	<message string>	This event is used to report MFIDE2 interface's warning/error messages [ “W: MF OK” (MFIDE2 interface properly initialized), “E: MF CONF MISS” (MFIDE2 interface configuration is missing), “E: WD NOTPRESENT” (Watchdog not found or not present on MFIDE2 equipment), “E: MF IDENT FAIL” (MFIDE2 interface identification failure), “E: MF DBL INIT” (MFIDE2 interface initialized more than once), “E: MF NOT INIT” MFIDE2 (interface not properly initialized)].
00154	WARNING	W: PNP DISABLED	PNP service is currently disabled.
00155	WARNING	W: NAT OVERFLOW	The NAT dynamic translation table has reached its capacity limit. In this situation, additional required translation cannot be performed.
00156	WARNING	W: TRACE DISK-FULL	The system wasn't able to save the Abilis CPX trace file because there wasn't enough space on HD/CF. When this event occurs the Abilis CPX trace file can be either partially saved or not saved at all.
00157	WARNING	W: SWITI SSSS-NN recovery NN OK	The 'NN' attempt of the SWITI driver of card 'SSSS-NN' failure recovering procedure was successful.
00158	WARNING	W: SWITI SSSS-NN recovery NN FAIL	Failure of the 'NN' attempt of the SWITI driver of card 'SSSS-NN' failure recovering procedure.
00159	WARNING	W: SWITI SSSS-NN failure, recovering...	The SWITI driver of card 'SSSS-NN' started the failure recovering procedure.
00160	WARNING	W: SWITI SSSS-NN recovered	A failure, that has been occurred on the SWITI driver of card 'SSSS-NN', has been recovered.
00161	ERROR	E: SWITI SSSS-NN unrecoverable failure	A not recoverable failure occurred on SWITI driver of card 'SSSS-NN'. For this reason the Abilis CPX system rebooted. Please report the event to the Abilis CPX Help desk.
00162	ERROR	E: SWITI error: reboot	A not recoverable error occurred on SWITI driver. For this reason the Abilis CPX system rebooted. Please report the event to the Abilis CPX Help desk.
00163	INFO	I: SYSTEM RESET	In the previous run the system was restarted using the RESTART SYSTEM command.
00164	INFO	I: RESET PRESSED	In the previous Abilis CPX run the system was restarted because the RESET button was pressed.
00165	WARNING	W: WDGMEM GETERR	The system didn't save system Watchdog memory content into Abilis CPX Exception Log file, because it wasn't able to access it. Please report the event to the Abilis CPX Help desk.
00166	WARNING	W: WDGMEM EMPTY	The system didn't save system Watchdog memory content into Abilis CPX Exception Log file, because it found it was empty.
00167	WARNING	W: WDGMEM SAVERR	The system tried to save system Watchdog memory content into Abilis CPX Exception Log file, because it found it wasn't successful.
00168	INFO	I: WDGMEM SAVED	The system Watchdog memory content has been successfully saved into Abilis CPX Exception Log file.
00169	WARNING	W: \USR DIR CREATE ERR-xx	The system wasn't able to create C:\USR directory at the Abilis CPX start-up. 'xx' is the error code to be reported to the Abilis CPX Help desk.
00170	WARNING	W: \USR\PUB DIR CREATE ERR-xx	The system wasn't able to create C:\USR\PUB directory at the Abilis CPX start-up. 'xx' is the error code to be reported to the Abilis CPX Help desk.
00171	WARNING	W: CONFLICTING CARD:Type-nnn DEACTIVATED	A card has been deactivated at system start up, because it was configured to use IRQ 14 or IRQ 15 in a system where this interrupts value should be reserved for IDE or MFIDE2 equipments. Please report the event to the Abilis CPX Help desk, together with the configuration file `drivers.cfg`. 'Type' is the card type; 'nnn' is the card identifier.
00172	INFO	I: Ftp-nnn ST:ss	Diagnostic information about the state of FTP Server resource. 'nnn' is the resource identifier; 'ss' is the FTP Server state [in (inactive), dn (down), RD (ready)].
00173	INFO	I: Bridge-nnn ST:s1.s2	Diagnostic information about the state of IEEE Bridge resource. 'nnn' is the resource identifier; 's1' is the Bridge resource global state [dn (down), RD (ready)]; 's2' is the Bridge resource links global state [dn (all links are in down state), rd (some links are in ready state), RD (all links are in ready state), np (no links are present)].
00174	INFO	I: Bridge-nnn LAN-ddd:ss	Diagnostic information about the state of a lan of IEEE Bridge resource. 'nnn' is the resource identifier; 'ddd' is the lan identifier; 'ss' is the lan state [dn (down), np (link not-present), DN (lower layer is down), RD (ready)].
00175	INFO	I: Bridge-nnn LNK-ddd:ss	Diagnostic information about the state of a link of IEEE Bridge resource. 'nnn' is the resource identifier; 'ddd' is the link identifier; 'ss' is the link state [dn (down), np (link not-present), DN (lower layer is down), RD (ready)].
00176	INFO	I: Arc-nnn ST:ss	Diagnostic information about the Archive resource state. 'nnn' is the resource identifier; 'ss' is the resource state [in (initialization), dn (down), RD (active/ready)].
00177	INFO	I: Arc-nnn SES-dd:ss	Diagnostic information about a session of the Archive resource 'nnn' is the resource identifier; 'dd' is the session identifier; 'ss' is the session state [in (initialization), dn (down), RD (active/ready)].
00178	WARNING	W: \LOG DIR CREATE ERR-xx	The system wasn't able to create C:\LOG directory at the Abilis CPX start-up. 'xx' is the error code to be reported to the Abilis CPX Help desk.
00179	INFO	I: CtiP-nnn L1-ST:ss	Diagnostic information about the Primary Rate layer 1 of a CTI port. 'nnn' is the CTI port identifier; 'ss' is the state of the layer 1 [dn (down), up].
00180	INFO	I: CtiP-nnn L1-ST:ss	Diagnostic information about the Basic Rate layer 1 of a CTI port. 'nnn' is the CTI port identifier; 'ss' is the state of the layer 1 [dn (down), RD (ready), HL (halted), FL (failed)].
00181	INFO	I: CtiP-nnn SapiQ931:s1 SapiX25:s2	Diagnostic information about the Primary Rate layer 2 (LAPD) of a CTI port. nnn' is the CTI port identifier; 's1' is the state of the Q.931 Sapi [in (inactive), dn (down), UP]; 's2' is the state of the X.25 Sapi [in (inactive), dn (down), UP].
00182	INFO	I: CtiP-nnn SapiX25:ss	Diagnostic information about the Basic Rate layer 2 (LAPD) of a CTI port.'nnn' is the CTI port identifier; 'ss' is the state of the X.25 Sapi [in (inactive), dn (down), UP].
00183	WARNING	W: ESB2 PCI fail	Failure in ESB2 card driver. Please report the error to the Abilis CPX Help desk.
00184	WARNING	W: ESB2 PCIS fail	Failure in ESB2 card driver. Please report the error to the Abilis CPX Help desk.
00185	WARNING	W: ESB2 JBC dd	Failure in ESB2 card driver. Please report the error to the Abilis CPX Help desk.
00186	WARNING	W: ESB2 EBIR0 fail	Failure in ESB2 card driver. Please report the error to the Abilis CPX Help desk.
00187	WARNING	W: ESB2 E-CRC fail	Failure in ESB2 card driver. Please report the error to the Abilis CPX Help desk.
00188	WARNING	W: DHCP STOPPED	Severe error in the DHCP driver related to bindings file `dchp.bnd`. Please report the error to the Abilis CPX Help desk.
00189	WARNING	W: Ospf LSA OVERFLOW	The 'LSA' table of Ospf resource reached its maximum capacity.
00190	WARNING	W: Ospf LSA DANGER ON	The 'LSA' table of Ospf resource in going in 'DANGER' state.
00191	WARNING	W: Ospf LSA DANGER OFF	The 'LSA' table of Ospf resource is exiting the 'DANGER' state.
00192	WARNING	W: Ospf ROUTE OVERFLOW	The 'ROUTE' table of Ospf resource reached its maximum capacity.
00193	WARNING	W: Ospf ROUTE DANGER ON	The 'ROUTE' table of Ospf resource is going in 'DANGER' state.
00194	WARNING	W: Ospf ROUTE DANGER OFF	The 'ROUTE' table of Ospf resource is exiting from 'DANGER' state.
00195	INFO	I: CHKDSK <drive> OK	The integrity check of the disk <drive> has been successfully executed and no errors were found.
00196	WARNING	W: CHKDSK <drive> ERRORs FOUND	The integrity check of the disk <drive> detected error(s). It's the first one of a set of messages (see System Log event 00197). Please report the error to the Abilis CPX Help desk.
00197	WARNING	W: CHKDSK ERROR: ssss	The integrity check of the disk <drive> detected the reported error 'ssss'.
00198	INFO	I: ESB2 SRC Update	Information message related to ESB2 card driver, i.e. src code should be updated. Please report the event to the Abilis CPX Help desk.
00199	WARNING	W: ESB2 OLD FW	Failure in ESB2 card driver, i.e. old firmware, ESB2 cannot be started. Please report the error to the Abilis CPX Help desk.
00200	WARNING	W: Invalid ESB	Failure in ESB2 card driver, i.e. ESB card is invalid. Please report the error to the Abilis CPX Help desk.
00201	WARNING	W: ESB2 FALC Fail1	Failure in ESB2 card driver, i.e. troubles during the FALC configuration. Please report the error to the Abilis CPX Help desk.
00202	WARNING	W: ESB2 FALC Fail2	Failure in ESB2 card driver, i.e. troubles during the FALC registers aren't accessible. Please report the error to the Abilis CPX Help desk.
00203	WARNING	W: ESB2 FALC Fail3	Failure in ESB2 card driver, i.e. troubles during the FALC refresh. Please report the error to the Abilis CPX Help desk.
00204	INFO	I: Sync-nnn LOOP ss	Execution on a Synchronous resource of the command for setting up the loop-back feature. 'ss' is the state of the loop-back which has been set up; 'nnn' is the Synchronous resource identifier.
00205	INFO	I: CP LOOP ss RES:Sync-nnn	Execution on a Synchronous resource of the command for setting up the loop-back feature. 'nnn' is the Synchronous resource identifier; 'ss' is the state of the loop-back which has been set up.
00206	ERROR	E: ssssss INIT ERROR	FPanel interface's initialization error messages. Please report the error to the Abilis CPX Help desk. 'ssssss' is the FPanel interface type: “FP-IDE” or “FP-LPT”.
00209	WARNING	W: EXCP TOUT	In the previous system run a sw exception occurred, but the exception handing procedure has been timed-out. Please report the error to the Abilis CPX Help desk.
00210	WARNING	W: WS TOUT	In the previous system run a request for unconditional system restart has been submitted by the user, through the WARM START command, but the procedure has been timed-out. Please report the error to the Abilis CPX Help desk.
00211	WARNING	W: RS TOUT	In the previous system run a request for system restart has been submitted by the user through the RESTART SYSTEM command, but the procedure has been timed-out. Please report the error to the Abilis CPX Help desk.
00212	INFO	I: SET BOOT VER xxxxxxxx	'SYS SET BOOT VERSION command has been executed. At next system start-up the version 'xxxxxxxx' of the Abilis CPX sw will be loaded.
00213	WARNING	W: QFALC SSSS-NN manual restart	Manually activated hardware reset of QuadFALC of card 'SSSS-NN'.
00214	WARNING	W: QFALC SSSS-NN automatic restart	Automatically performed hardware reset of QuadFALC of card 'SSSS-NN'.
00215	WARNING	W: SWITI SSSS-NN manual restart	Manually activated hardware reset of SWITI of card 'SSSS-NN'.
00216	WARNING	W: \PKG DIR CREATE ERR-xx	The system wasn't able to create C:\PKG directory at the Abilis CPX start-up. 'xx' is the error code to be reported to the Abilis CPX Help desk.
00217	WARNING	W: ESB-nnn INT FAIL	The interface module of the ESB card 'nnn' returned an invalid type code, it's probably damaged. Please report the error to the Abilis CPX Help desk.
00218	WARNING	W: \APP DIR CREATE ERR-xx	The system wasn't able to create C:\APP directory at the Abilis CPX start-up. 'xx' is the error code to be reported to the Abilis CPX Help desk.
00219	WARNING	W: CONF RELOAD	The configuration reloading procedure has been activated.
00220	WARNING	W: CONF RELOAD ABORT	The configuration reloading procedure failed and has been aborted because of an error.
00221	INFO	I: DEBUG SIMULATE EXCEPTION	The DEBUG SIMULATE EVENT:xcp command has been executed.
00222	INFO	I: DEBUG SIMULATE WDLIVE-1	The DEBUG SIMULATE EVENT:wdl command has been executed.
00223	WARNING	W: HFC2 JBC nn	Error in downloading firmware to HFC2 card. Please report the error to the Abilis CPX Help desk
00224	WARNING	W: SSSS-NN EEPROM Chunk:dd Code:ss	Problems for cards that use serial EEPROM for identification. The problem happens during information downloading by the driver of the card 'SSSS-NN'. The EEPROM it's probably damaged. Please report the error to the Abilis CPX Help desk.
00225	INFO	I: CtiP-nnn L1-ST:ss	This event reports diagnostic information about the layer 1 of a CTI port belonging to a POTS card. 'nnn' is the CTI port identifier;'ss' is the state of the layer 1 [ONH (the port HOOK is ON), RING (the phone is RINGING), OFFH (the port HOOK is OFF), down (the port is administratively deactivated by OPERSTATE:DOWN), stby (the port is in stand-by mode, which is a mode with limited power consumption and an automatic recovery to normal operation when telephone goes off-hook or an incoming call has to be delivered, FAIL (the port is in FAILED state, because of detected errors during the initialization or running)].
00226	ERROR	E: MISSING '<file-name>'	The mandatory '<file-name>' file is missing. By consequence of this the system will be restarted. Please report the event to the Abilis CPX Help desk.
00227	WARNING	W: CtiP-nnn MISSING <file-name>	This event is used only by CTI ports belonging to a POTS card, it informs that the specified country coefficient file is missing. 'nnn' is the CTI port identifier; '<file-name>' is the name of the required country coefficient file.
00228	WARNING	W: CtiP-nnn CHECKSUM FAIL	This event is used only by CTI ports belonging to a POTS card, it informs that the checksum verification fails. 'nnn' is the CTI port identifier.
00229	WARNING	W: INV RING DEF	This event is used only by a POTS card, it informs that the Ring signal definition isn't valid.
00230	INFO	I: Dsl-nnn ST:ss	Diagnostic information about an DSL resource. 'nnn' is the DSL resource identifier; 'ss' is the DSL resource state [ DOWN, BLCK (blocked), SYNC (synchronizing), UP].
00231	INFO	I: IpSec-nnn ST:ss	Diagnostic information about IpSec resource. 'nnn' is the IpSec resource identifier. (only value 1 is possible); 'ss' is the IpSec resource state [in (IpSec is inactive), RD (IpSec is active)].
00232	INFO	I: Ike-nnn ST:ss/tt	Diagnostic information about IKE resource. 'nnn' is the IKE resource identifier. (only value 1 is possible); 'ss' is the IKE resource state [dn (IKE isn't functioning), in (IKE administratively set inactive), RD (IKE is active), ig (IKE is executing INIT command)]; 'tt' is the IpSec resource state [dn (Ipsec isn't functioning), in (IpSec administratively set inactive), RD (IpSec is active), ig (IpSec is executing INIT command)].
00233	INFO	I: Ike-nnn HOST:h IP:x.x.x.x:y s	Diagnostic information about IKE resource. 'nnn' is the IKE resource identifier (only value 1 is possible); 's' is the IKE HOST SA state [UP ( connection opened), dn (connection closed)].
00234	WARNING	W: SYNC-nnn Interface failure	Unsupported or defective interface module has been detected for the indicated SYNC interface. Please report the error to the Abilis CPX Help desk. 'nnn' is the SYNC resource identifier.
00235	WARNING	W: DSL-nnn (xxx) RSTR AUTO	The specified DSL modem has been restarted automatically as a consequence of a serious anomaly, precisely the modem stopped to respond. 'nnn' is the DSL resource identifier. 'xxx' is the internal Abilis CPX port number, as seen through D PSTACK command.
00236	WARNING	W: DSL-nnn STH Invalid Modem type	A modem of STH family is connected but it isn't supported by Abilis CPX. 'nnn' is the DSL resource identifier.
00237	WARNING	W: ETH-nnn Failed Reset	An attempt to reset the indicated ETH interface failed. 'nnn' is the ETH resource identifier.
00238	WARNING	W: ETH-nnn Filter Overflow	The MAC addresse filter table needed for IEEE bridge functionality was saturated. 'nnn' is the ETH resource identifier.
00239	INFO	I: ETH-nnn Limited Auto Mode	This event should not happen, it's reserved to development process. 'nnn' is the ETH resource identifier.
00240	WARNING	W: cccc-nnn DELIC DWNL FAIL eee	Failure during the download of firmware into DELIC chip of BRI4 and BRI8 cards. It must be reported to the Abilis CPX Helpdesk. 'cccc' is the type of the card, either BRI4 or BRI8; 'nnn' is the BRI4 or BRI8 card identifier; 'eee' is the internal error code.
00241	WARNING	W: POTS-nnn 12V Absent	12V voltage isn't supplied to the indicated POTS card. 'nnn' is the POTS card identifier.
00242	INFO	I: cccc-nnn DSP:xx DWNL OK	Successful download of firmware into indicated DSP. 'cccc' is the type of the card where DSP is hosted; 'nnn' is the card identifier where DSP is hosted; 'xx' is the DSP identifier on the specified card.
00243	INFO	I: cccc-nnn DSP:xx DWNL KR FAIL	Kernel download failure for the indicated DSP. 'cccc' is the type of the card where DSP is hosted; 'nnn' is the card identifier where DSP is hosted; 'xx' is the DSP identifier on the specified card.
00244	INFO	I: cccc-nnn DSP:xx DWNL PR FAIL	Program download failure for the indicated DSP. 'cccc' is the type of the card where DSP is hosted; 'nnn' is the card identifier where DSP is hosted; 'xx' is the DSP identifier on the specified card.
00245	INFO	I: cccc-nnn DSP:xx RSTR USER	Manual restart of the indicated DSP through R CTIAC command. 'cccc' is the type of the card where DSP is hosted; 'nnn' is the card identifier where DSP is hosted; 'xx' is the DSP identifier on the specified card.
00246	INFO	I: cccc-nnn DSP:xx RSTR AUTO	The occurrence of an automatic restart of the indicated DSP as a consequence of a DSP blockage automatically detected. 'cccc' is the type of the card where DSP is hosted; 'nnn' is the card identifier where DSP is hosted; 'xx' is the DSP identifier on the specified card.
00247	INFO	I: cccc-nnn DSP:xx RSTR FAIL	The automatic restart of DSP did not succeed three times consecutively, and DSP is permanently put in failed state. 'cccc' is the type of the card where DSP is hosted; 'nnn' is the card identifier where DSP is hosted; 'xx' is the DSP identifier on the specified card.
00248	INFO	I: USB PCIxx/yy tttt aaaa ii	This event indicates recognized USB controllers, I/O mapped. 'xx' is the PCI SlotId of the controller, as shown with the D PCIDEV command; 'yy' is the PCI Function of the controller, as shown with the D PCIDEV command; 'tttt' is the type of controller, which can be OHCI, UHCI or EHCI; 'aaaa' isthe I/O address at which controller is accessible; 'ii' is the IRQ assigned to the controller.
00249	INFO	I: USB PCIxx/yy tttt aaaaaaaa ii	This event indicates recognized USB controllers, memory mapped. 'xx' is the PCI SlotId of the controller, as shown with the D PCIDEV command; 'yy' is the PCI Function of the controller, as shown with the D PCIDEV command; 'tttt' is the type of controller, which can be OHCI, UHCI or EHCI; 'aaaaaaaa' is the memory address at which controller is accessible; 'ii' is the IRQ assigned to the controller.
00250	INFO	I: USB PCIxx/yy Failure	Failure in the operation with the indicated USB controller. 'xx' is the PCI SlotId of the controller, as shown with the D PCIDEV command; 'yy' is the PCI Function of the controller, as shown with the D PCIDEV command.
00251	WARNING	W: LDM Corrupted, LDM Cleared	A content corruption occurred for the debug log in memory. The log had to be cleared in order to recover from the error.
00252	INFO	I: Smtp-1 ST:ssss	SMTP Server resource state information. 'ssss' is the resource state [RD (ACTIVE), in (INACTIVE)].
00253	INFO	I: Pop3-1 ST:ssss	POP3 Server resource state information. 'ssss' is the resource state [RD (ACTIVE), in (INACTIVE)].
00254	INFO	I: POWER ON	WDG detects that in the previous run CPX was switched off.
00255	INFO	I: WATCHDOG xx	Hw Interface initialization/detection success notification. 'xx' identifies the Front Panel/WatchDog interface type.
00256	WARNING	W: ABNORMAL SYSTEM REBOOT	SYSTEM was abnormal rebooted; LIVE state was detected during the boot phase.
00257	INFO	I: SYSTEM LOG CLEARED	System log clearing event; i.e. C L command was issued.
00258	INFO	I: PoeCli-nnn ST:ssss	Diagnostic information: PoeCli resource. 'nnn' is the resource identifier; 'ssss' is the resource state [dn (DOWN), RD (READY)]
00259	INFO	I: PoeAc-nnn ST:ssss	Diagnostic information: PoeAc resource. 'nnn' is the resource identifier; 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE), ee (ETH-ERROR)]
00260	WARNING	W: WATCHDOG DISABLED	Watchdog is disabled.
00261	WARNING	W: WATCHDOG NOT DRIVEN	Watchdog isn't driven.
00262	INFO	I: CPX LIGHT EDITION	CPX is running its Light edition.
00264	INFO	I: CtiGkc-1 ST:ssss	Diagnostic information about CtiGkc resource.
00265	INFO	I: CtiIax-1 ST:ssss	Diagnostic information about CtiIax resource. 'ssss' is the resource state [in (INACTIVE), AC (ACTIVE)].
00266	INFO	I: CtiDisa-1 ST:ssss	Diagnostic information about CtiDisa resource. 'ssss' is the resource state [in (INACTIVE), AC (ACTIVE)].
00267	INFO	I: CtiP-nnn VOICE-ST:sss1 PDN-ST:sss2	Diagnostic information about CTI port belonging to CELL (GSM/UMTS) card. 'nnn' is the CTI port number.
00268	INFO	I: Radius-1 ST:ssss	Diagnostic information about Radius resource. 'ssss' is the resource state [dn (DOWN), in (INACTIVE), RD (ACTIVE)].
00269	INFO	I: Vrrp-1 ST:ssss	Diagnostic information about Vrrp resource. 'ssss' is the resource state [dn (DOWN), in (INACTIVE), RD (ACTIVE)].
00270	INFO	I: Ip-nnn ST:sss1 LINK:sss2	Diagnostic information about IP resource. 'nnn' is the resource identifier; 'sss1' is the main resource state [DN (DOWN), UP (UP), gU (GOING-UP), gD (GOING-DOWN)]; 'sss2' is the link state [ld (LINKDOWN), LR (LINKREADY), ln (LINKNOTPRESENT), RD (X25READY), cg (X25CALLING), cd (X25CALLED), CN (X25CONNECTED), dl (X25DELAY), wt (X25WAITING), ht (HALTED), fl (FAILED)].
00271	INFO	I: CtiSip-1 ST:ssss	Diagnostic information about CTISIP resource. 'ssss' is the resource state [in (INACTIVE), AC (ACTIVE)].
00272	INFO	I: Stun-1 ST:ssss	Diagnostic information about Stun resource. 'ssss' is the resource state [in (INACTIVE), RD (READY)].
00273	WARNING	W: USB autoreset parent hub of xxx	USB Reset of the device's parent hub; 'xxx' is the number of USB port.
00274	WARNING	W: USB unavailable parent hub of xxx	USB Unavailable device's parent hub; 'xxx' is the number of USB port.
00275	INFO	I: TRACE AUTO SAVE: STARTED	Automatic tracer saving feature: the trace has started.
00276	WARNING	W: TRACE AUTO SAVE: TSAVE:NO	Automatic tracer saving feature: the `TSAVE` parameter is set to NO.
00277	WARNING	W: TRACE AUTO SAVE: REQ CANCELLED	Automatic tracer saving feature: the trace has received a request for cancellation.
00278	WARNING	W: TRACE AUTO SAVE: TRACE NOTRUNNING	Automatic tracer saving feature: the trace isn't running.
00279	INFO	I: TRACE AUTO SAVE: TRACE STOPPED	Automatic tracer saving feature: the trace has been stopped.
00280	INFO	I: TRACE AUTO SAVE: TRACE SAVED	Automatic tracer saving feature: the trace has been saved.
00281	WARNING	W: TRACE AUTO SAVE: TRACE NOT SAVED	Automatic tracer saving feature: the trace has not been saved.
00282	INFO	I: TRACE AUTO SAVE: TRACE EMPTY	Automatic tracer saving feature: the trace is empty.
00283	INFO	I: TRACE AUTO SAVE: TRACE RE-STARTED	Automatic tracer saving feature: the trace has been restarted.
00284	INFO	I: DEBUG SIMULATE TRACE AUTO SAVE	The DEBUG SIMULATE EVENT:tsave command has been executed.
00285	WARNING	W: CTIR DISABLED	The DISABLE CTIR command has been executed.
00286	INFO	I: CTIR ENABLED	The ENABLE CTIR command has been executed.
00287	WARNING	W: AC DISABLED	The DISABLE AC command has been executed.
00288	INFO	I: AC ENABLED	The ENABLE AC command has been executed.
00289	INFO	I: UpnpC-1 ST:ssss	Diagnostic information about UpnpC resource. 'ssss' is the resource state [in (INACTIVE), RD (READY)].
00290	INFO	I: UpnpS-1 ST:ssss	Diagnostic information about UpnpS resource. 'ssss' is the resource state [in (INACTIVE), RD (READY)].
00291	INFO	I: DSP test start	DSP Test: Start test.
00292	INFO	I: DSP test end	DSP Test: End test.
00293	WARNING	W: cccc-nnn DSP#n ssss recover	DSP Test: Recovery attempt. 'cccc' is the type of the card and 'nnn' is the card identifier.
00294	WARNING	W: cccc-nnn DSP#n ssss bad	DSP Test: DSP failure. 'cccc' is the type of the card and 'nnn' is the card identifier.
00295	WARNING	W: CELL-nnn - AT RX garbage XX	CELL message, AT RX garbage 1.
00296	WARNING	W: CELL-nnn - AT RX garbage	CELL message, AT RX garbage 2.
00297	WARNING	W: CELL-nnn - SHUTDOWN DD	CELL message, SHUTDOWN URC on GSM detected.
00298	WARNING	W: CELL-nnn - PIN STATE FAIL	CELL message, PIN state fail on UMTS detected.
00299	WARNING	W: CELL-nnn - UNKNOWN DISC REASON DD	CELL message, UNKNOWN disconnect reason.
00300	WARNING	W: CELL-nnn - PUK REQUIRED	CELL message, PUK required CME error.
00301	WARNING	W: CELL-nnn - Invalid PIN	CELL message, INVALID PIN CME error.
00302	WARNING	W: CELL-nnn - Invalid PIN2	CELL message, INVALID PIN2 CME error.
00303	WARNING	W: CELL-nnn - Invalid PUK	CELL message, INVALID PUK CME error.
00304	WARNING	W: CELL-nnn - Invalid PUK2	CELL message, INVALID PUK2 CME error.
00305	INFO	I: Opc-1 ST:ssss	Diagnostic information about Opc resource. 'ssss' is the resource state [DN (DOWN), UP].
00306	INFO	I: SysLog-1 ST:ssss	Diagnostic information about SysLog resource. 'ssss' is the resource state [in (INACTIVE), RD (READY)].
00307	INFO	I: Rjs-nnn ST:sss1 USB-ST:sss2	Diagnostic information about Rjs resource. 'nnn' is the resource identifier; 'sss1' is the resource state [DN (DOWN), UP, in (INACTIVE)]; 'sss2' is the USB state [ ds (DISCONNECTED), CN (CONNECTED)].
00308	WARNING	W: cccc-nnn ssss FW - C:n.m - R:x.y	C64xx error, incorrect FW version. 'cccc' is the type of the card and 'nnn' is the card identifier.
00309	WARNING	W: cccc-nnn ssss FW missing	C64xx error, missing FW. 'cccc' is the type of the card and 'nnn' is the card identifier.
00310	WARNING	W: cccc-nnn ssss FW damaged	C64xx error, FW damaged - not BIH file. 'cccc' is the type of the card and 'nnn' is the card identifier.
00311	WARNING	W: cccc-nnn C64xx FW Init failed	C64xx error, initialization failed. 'cccc' is the type of the card and 'nnn' is the card identifier.
00312	WARNING	W: cccc-nnn FPGA FW missing	QPRIX error, missing FPGA FW. 'cccc' is the type of the card and 'nnn' is the card identifier.
00313	WARNING	W: cccc-nnn C64xx CCB Init failed	QPRIX error, CCB initialization failed. 'cccc' is the type of the card and 'nnn' is the card identifier.
00314	WARNING	W: cccc-nnn C64xx PCM Init failed	QPRIX error, PCM initialization failed. 'cccc' is the type of the card and 'nnn' is the card identifier.
00315	INFO	I: SimBox-nnn ST:sss1 USB-ST:sss2	Diagnostic information about SimBox resource. 'nnn' is the resource identifier; 'sss1' is the resource state [DN (DOWN), UP, in (INACTIVE)]; 'sss2' is the USB state [ ds (DISCONNECTED), CN (CONNECTED)].
00316	ERROR	W: cccc-nnn C64xx IQ overflow	QPRIX error, interrupt queue overflow. 'cccc' is type of the card and 'nnn' is the card identifier.
00317	INFO	CONF:MOVED DRIVERS.CFG TO DRIVERS.BAD	Corrupted Configuration file copied to DRIVERS.BAD file.
00318	INFO	I: Gps-nnn ST:sss1 USB-ST:sss2	Diagnostic information about Gps resource. 'nnn' is the resource identifier; 'sss1' is the resource state [DN (DOWN), UP, in (INACTIVE)]; 'sss2' is the USB state [ ds (DISCONNECTED), CN (CONNECTED)].
00321	WARNING	W: <user>-in.log CORRUPTED	The Incoming Calls log file of the specified user <user> is corrupted.
00322	WARNING	W: <user>-in.log DELETED	The Incoming Calls log file of the specified user <user> was deleted.
00323	WARNING	W: <user>-out.log CORRUPTED	The Outgoing Calls log file of the specified user <user> is corrupted.
00324	WARNING	W: <user>-out.log DELETED	The Outgoing Calls log file of the specified user <user> was deleted.
00325	INFO	I: Gpio-nnn ST:sss1 USB-ST:sss2	Diagnostic information about Gpio resource. 'nnn' is the resource identifier; 'sss1' is the resource state [DN (DOWN), UP, in (INACTIVE)]; 'sss2' is the USB state [ ds (DISCONNECTED), CN (CONNECTED)].
00326	INFO	I: GpioPc-nnn ST:ssss	Diagnostic information about GpioPc resource. 'nnn' is the resource identifier; 'ssss' is the resource state [DN (DOWN), UP]
00327	INFO	I: CtiSms-1 ST:ssss	Diagnostic information about CtiSms resource. 'ssss' is the resource state [ dn (INACTIVE), RD (ACTIVE)]
00328	INFO	W: cccc-nnn FPGA FW - C:n.m - R:x.y	QPRIX error, incorrect FPGA FW version. 'cccc' is type of the card and 'nnn' is the card identifier.
00329	ERROR	E: EEC open - XX - ssss	Echo canceler channel open fail.
00330	INFO	I: Sntp-1 CLI-ST:ssss	Diagnostic information about Sntp resource, where 'ssss' is the SNTP client state [in (INACTIVE), dn (ACTIVE), RD (READY), dg (DISCONNECTING), hl (HALTED), ds (DISABLED)].
00331	WARNING	W: cccc-nnn FPGA init failed	HFC3 error, cannot init (upload FW) FPGA (SWIX). 'cccc' is the type of the card and 'nnn' is the card identifier.
00332	WARNING	W: \LICENCE DIR CREATE ERR-XX	System wasn't able to create C:\LICENCE directory at start-up.
00336	WARNING	W: FW UPLOAD START XXXX XXXX ssss	USB BootLoader, FW Update started.
00337	WARNING	W: FW UPLOAD SUCCESS XXXX XXXX ssss	USB BootLoader, FW Update success.
00338	WARNING	W: FW UPLOAD FAILURE XXXX XXXX ssss	USB BootLoader, FW Update failure.
00339	WARNING	W: FW MISSING <file-name>	USB BootLoader, FW <file-name> file is missing.
00340	WARNING	W: FW UPLOAD REQUEST XXXX XXXX ssss	USB BootLoader, FW Update request.
00341	WARNING	W: FW UPLOAD REQUEST SUCCESS XXXX XXXX ssss	USB BootLoader, FW Update request success.
00342	WARNING	W: FW UPLOAD REQUEST FAIL XXXX XXXX ssss	USB BootLoader, FW Update request fail.
00343	WARNING	W: FW UPLOAD SKIPPED XXXX XXXX ssss	USB BootLoader, FW Update skipped.
00344	INFO	I: Ip-nnn ST:sss1 LINK:ssss2 PING:sss3	Diagnostic information about IP resources. 'nnn' is the resource identifier; 'sss1' is the main resource state [DN (DOWN), UP (UP), gU (GOING-UP), gD (GOING-DOWN)]; 'sss2' is the link state [ld (LINKDOWN), LR (LINKREADY), ln (LINKNOTPRESENT), RD (X25READY), cg (X25CALLING), cd (X25CALLED), CN (X25CONNECTED), dl (X25DELAY), wt (X25WAITING), ht (HALTED), fl (FAILED)] and 'sss3' is the ping state [DN (DOWN), UP, UN (UNKNOWN)].
00345	INFO	I: Dhcp-1 ST:ssss	Diagnostic information about Dhcp resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE), st (STOPPED)].
00346	INFO	I: DhcpC-1 ST:ssss	Diagnostic information about DhcpC resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE)].
00347	ERROR	E: USB EXIT MSG: ssss	USB fatal exit, 'ssss' is the reported error message.
00348	ERROR	E: USB EXIT CODE: nnnn	USB fatal exit, 'nnnn' is the reported error code.
00349	INFO	I: Ddns-1 ST:ssss	Diagnostic information about Ddns resource. 'ssss' is the resource state [RD (READY), in (INACTIVE)].
00350	INFO	I: TIME CHANGE, from UTC to LOCAL time	Time service information: change from UTC to LOCAL time.
00351	INFO	I: TIME CHANGE, S T command executed	Time service information, S T command executed.
00352	INFO	I: LOCAL vs. RTC resyn, Delta > 1 min.(nn sec.)	Time service information, RTC resyncronisation.
00353	INFO	I: LOCAL vs. RTC resyn done	Time service information, RTC resyncronization done.
00354	INFO	I: Upgrade from version prior to 7.0.0	Time service information, detected upgrade from ver. < 7.0.0.
00355	INFO	I: CMOS clock changed from LOCAL to UTC time	Time Service information, CMOS clock changed from LOCAL to UTC time
00356	INFO	I: C:\TIMECFG.DAT missing, indicated time is UTC	Time Service information, C:\TIMECFG.DAT file is missing.
00357	INFO	I: TIME CHANGE, from <zone1> to <zone2> time zone	Time Service information, time zone changed from <zone1> to <zone2> time zone.
00358	INFO	LINUX WARM START	System warm start, requested by LINUX OS.
00359	INFO	SHUTDOWN	System shutdown, requested by Abilis CPX.
00360	INFO	LINUX SHUTDOWN	System shutdown, requested by LINUX OS.
00361	ERROR	E: MFPCI or MFIDE3(FW Rev. >= 28) is required	Incorrect Hw interface (WatchDog, LCD display, etc) found.
00362	INFO	I: WATCHDOG MFIDE3 FW Rev. nnn	MFIDE3 firmware version report.
00363	ERROR	E: MFIDE3 FW Rev. 28 or higher is required	Incorrect MFIDE3 firmware version.
00364	INFO	I: Rsim-nnn ST:ssss	Diagnostic information about RSim resource. 'nnn' is the Rsim resource identifier. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE)].
00365	INFO	I: DEBUG SIMULATE BLOCKAGE	The DEBUG SIMULATE EVENT:blockage command has been executed.
00366	WARNING	W: LICENCE, FILE MISSING	Licence not activated because the licence file is missing.
00367	WARNING	W: LICENCE, FILE CORRUPTED	Licence not activated because the licence file content isn't valid.
00368	WARNING	W: LICENCE, ABILIS-ID MISMATCH	Licence not activated because Abilis ID reported in the licence file isn't valid.
00369	WARNING	W: LICENCE, EXPIRED	Licence not activated because it's expired.
00370	WARNING	W: LICENCE, LOAD ERROR XXXX (ssss)	Licence not specified error. 'xxxx' is the error code and 'ssss' is the raw description.
00371	INFO	I: LICENCE, LOADED	Licence successfully activated.
00372	ERROR	E: MISSING 'VMX' LICENCE	Missing VMX Licence error message.
00373	INFO	W: LICENCE, rrrr-nnn NOT ACTIVATED	Not licenced resource warning message, where 'rrrr' is the resource type and 'nnn' is the resource identifier.
00374	INFO	W: LICENCE, <service> DISABLED	Not licenced service warning message: the specified <service> service was disabled.
00375	INFO	W: LICENCE, IKE HOSTs NUMBER CHANGED	IKE HOSTs number changed: the parameter 'max-hosts' has been set equal to IKEHOSTS licence value.
00376	INFO	AUTO SAVE FAIL, RC:XX (ssss)	Auto-save of configuration file failure. 'xxxx' is the error code and 'ssss' is the raw description.
00377	WARNING	W: <user>-in.log BAD VERSION	The Incoming Calls log file of the specified user <user> has invalid version.
00378	WARNING	W: <user>-in.log CONVERTED	The Incoming Calls log file of the specified user <user> was converted to the correct version.
00379	WARNING	W: <user>-out.log BAD VERSION	The Outgoing Calls log file of the specified user <user> has invalid version.
00380	WARNING	W: <user>-out.log CONVERTED	The Outgoing Calls log file of the specified user <user> was converted to the correct version.
00381	WARNING	W: CTIR DB overflow.	CTIR internal DB overflow.
00382	WARNING	W: cccc-nnn, Debug mode, FW not downloaded	QPRIX debug mode, FW not downloaded. 'cccc' is the type of the card and 'nnn' is the card identifier.
00383	WARNING	W: cccc-nnn, C64xx channel config failed	QPRIX Channel configuration. 'cccc' is the type of the card and 'nnn' is the card identifier.
00384	WARNING	W: Ip-nnn NAT ALIAS networks overflow	IP resource: NAT ALIAS networks overflow. 'nnn' is the IP resource identifier.
00385	WARNING	W: Ip-nnn VIRTUAL secondary networks overflow	IP resource: VIRTUAL SECONDARY networks overflow. 'nnn' is the IP resource identifier.
00386	WARNING	W: Ip-nnn VRRP networks overflow	IP resource: VRRP VIRTUAL networks overflow. 'nnn' is the IP resource identifier.
00387	INFO	I: DSL-nnn ST:ssss TX/RX:xxxx/yyyy	Diagnostic information about DSL resource. 'nnn' is the DSL resource identifier. 'ssss' is the resource state [DOWN, BLCK (BLOCKED), SYNC (SYNCHRONISING), UP, FAIL, TEST, RTN (RETAIN)]. 'xxxx' and 'yyyy' are transmission and reception speeds.
00388	INFO	I: Tftp-1 ST:ssss	Diagnostic information about TFTP resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE)].
00389	INFO	I: Alarm-1 ST:ssss	Diagnostic information about Alarm resource. 'ssss' is the resource state [RD (READY), in (INACTIVE)].
00390	INFO	I: CtiVm-1 ST:ssss	Diagnostic information about CtiVm resource. 'ssss' is the resource state [RD (READY), in (INACTIVE)].
00391	INFO	I: CtiVr-1 ST:ssss	Diagnostic information about CtiVr resource. 'ssss' is the resource state [RD (READY), in (INACTIVE)].
00392	INFO	I: IpSh-1 ST:ssss	Diagnostic information about IpSh resource. 'ssss' is the resource state [dn (DOWN), RD (READY)].
00393	ERROR	E: USB EXIT THREAD: nnn	USB fatal thread: 'nnn' is the thread active at the moment of the problem.
00394	INFO	I: DEBUG SIMULATE WDG RESET	The DEBUG SIMULATE EVENT:wdgreset command has been executed.
00395	INFO	I: WDG RESET INEFFECTIVE	The DEBUG SIMULATE EVENT:wdgreset command has been executed but the WDG reset hadn't effect.
00396	INFO	I: Vrrp-1 Router ID:nnn I-ST:sss1 ST:sss2	Vrrp Router state report.
00397	ERROR	E: POTS32-nnn failure. V-Maillbox unable to reset	V-Mailbox blocked (busy after two resets)
00398	INFO	I: ABILIS CPX Ver. nnnn - Build mmmm	Running Abilis CPX version/build.
00399	INFO	I: CtiP-nnn VOICE-ST:sss1 CITO:sss2 AUDIO:sss3	Diagnostic information about CTI port belonging to CITO card.
00400	WARNING	W: '<file-name>' '<error>'	The reported '<error>' occurred during the '<file-name>' file treatment. Please report the event to the Abilis CPX Help desk.
00401	INFO	I: Ldap-1 ST:ssss	Diagnostic information about LDAP resource. 'ssss' is the resource state [RD (READY), in (INACTIVE)].
00402	INFO	I: DEBUG SIMULATE LOOP 'nnn' msec	The DEBUG SIMULATE EVENT:loop command has been executed.
00403	ERROR	W: cccc-nnn C64xx IQ reset successful	QPRIX error, interrupt queue reset successful. 'cccc' is the type of the card and 'nnn' is the card identifier.
00404	ERROR	W: cccc-nnn C64xx IQ reset unsuccessful	QPRIX error, interrupt queue reset unsuccessful. 'cccc' is the type of the card and 'nnn' is the card identifier.
00405	WARNING	W: '<file-name>' '<error>' [nn] - ssss	The reported '<error>' occurred during the '<file-name>' file treatment. The number 'nn' is the occurred File System error code and 'ssss' is the related description. Please report the event to the Abilis CPX Help desk.
00406	INFO	I: Trfa-1 ST:ssss	Diagnostic information about Trfa resource. 'ssss' is the resource state [RD (READY), in (INACTIVE)].
00407	INFO	I: Rip-1 ST:ssss	Diagnostic information about Rip resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE)].
00408	INFO	I: Dns-1 ST:ssss	Diagnostic information about Dns resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE)].
00409	INFO	I: X509-1 ST:ssss	Diagnostic information about X509 resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE), ig (INIT)].
00410	INFO	I: Ssl-1 ST:ssss	Diagnostic information about Ssl resource. 'ssss' is the resource state [dn (DOWN), RD (READY)].
00411	INFO	I: Nat-1 ST:ssss	Diagnostic information about Nat resource. 'ssss' is the resource state [dn (DOWN), RD (READY)].
00412	INFO	I: Snmp-1 ST:ssss	Diagnostic information about Snmp resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE), dg (DISCONNECTING), hl (HALTED)].
00413	INFO	I: Http-1 ST:ssss	Diagnostic information about Http resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE)].
00414	INFO	I: Acnt-1 ST:ssss	Diagnostic information about Acnt resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE)].
00415	INFO	I: Ospf-1 ST:ssss	Diagnostic information about Ospf resource. 'ssss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE)].
00416	INFO	I: Mail Service filtering FIFO overflow (nn/NN)	Mail Service informations about the mail filtering FIFO overflow. 'nn' is the number of queued mails and 'NN' is the queue size.
00417	WARNING	W: OPC USER:<user> Table OVERFLOW	OPC has an USER table overflow state.
00418	WARNING	W: OPC USER:<user> CALL Table OVERFLOW	OPC has a CALL table overflow state.
00419	WARNING	W: OPC USER:<user> CALL-QUEUE Table OVERFLOW	OPC has a CALL QUEUE table overflow state.
00420	WARNING	W: WATCHDOG INVALID WDR VALUE, 0xHH	Hw interface, WatchDog: invalid WDG register value. Please report the event to the Abilis CPX Help desk.
00421	WARNING	W: CHKDSK <drive> ABORTED	The execution of integrity check of the disk <drive> exceeded the timed-out of 5 sec. has beeen aborted.
00422	WARNING	W: CHKDSK <drive> ERROR [nn] - ssss	An error occurred during the execution of integrity check of the disk <drive>. The number 'nn' is the occurred error code and 'ssss' is the related description. Please report the event to the Abilis CPX Help desk.
00423	INFO	W: LICENCE, SWAC CHANs NUMBER CHANGED	The CTISYS parameter 'swac-chans' value has been changed: it has been set equal to SWAC (Software Audio Compressor) licence value.
00424	INFO	I: Tcp-nnn ST:ssss	Diagnostic information about Tcp resource. 'ssss' is the resource state [dn (DOWN), RD (READY)].
00425	INFO	I: Udp-nnn ST:ssss	Diagnostic information about Udp resource. 'ssss' is the resource state [dn (DOWN), RD (READY)].
00426	INFO	I: Telnet-nnn ST:ssss	Diagnostic information about Telnet resource. 'ssss' is the resource state [dn (DOWN), RD (READY)].
00427	INFO	I: Ssh-nnn ST:ssss	Diagnostic information about SSh resource. 'ssss' is the resource state [dn (DOWN), RD (READY)].
00428	INFO	I: MFIo-nnn ST:ssss	Diagnostic information about MfIo resource. 'ssss' is the resource state [in (INACTIVE), RD (ACTIVE)].
00429	WARNING	W: LDAP - <file-name> version update required, from v. xxx to v. yyy	LDAP service need to update db file <file-name>.
00430	WARNING	W: LDAP - <file-name-1> v. xxx being saved in <file-name-2>	LDAP service, db file <file-name> save is in progress.
00431	WARNING	W: LDAP - <file-name-1> v. xxx saved in <file-name-2>	LDAP service, db file <file-name> successfully saved.
00432	WARNING	W: LDAP - Error nn (ssss) saving <file-name>.	LDAP service, db file <file-name> unsuccessful save. The number 'nn' is the occurred error code and 'ssss' is the related description. Please report the event to the Abilis CPX Help desk.
00433	WARNING	W: LDAP - <file-name> being updated to v. xxx	LDAP service, db file <file-name> version update is in progress.
00434	WARNING	W: LDAP - <file-name> successfully updated to v. xxx	LDAP service, db file <file-name> successfully updated.
00435	WARNING	W: LDAP - Error nn (ssss) updating <file-name>	LDAP service, db file <file-name> unsuccessful update. The number 'nn' is the occurred error code and 'ssss' is the related description. Please report the event to the Abilis CPX Help desk.
00436	INFO	I: MfTemp-nnn ST:ssss	Diagnostic information about MfTemp resource. 'ssss' is the resource state [in (INACTIVE), RD (ACTIVE)].
00437	INFO	I: SysCtl-nnn ST:ssss	Diagnostic information about SysCtl resource. 'ssss' is the resource state [in (INACTIVE), RD (ACTIVE)].
00438	WARNING	W: MAIL SERVICE SMTP ERROR [nn] - ssss	Mail Service: mail not sent because of SMTP driver error. The number 'nn' is the occurred error code and 'ssss' is the related description. Please report the event to the Abilis CPX Help desk.
00439	WARNING	W: MAIL SERVICE ERROR [nn] - ssss	Mail Service: mail not sent because of service internal error. The number 'nn' is the occurred error code and 'ssss' is the related description. Please report the event to the Abilis CPX Help desk.
00440	WARNING	W: DSL-nnn STH Unsupported FW version	DSL (STH) modem - unsupported FW version. 'nnn' is the resource identifier.
00441	WARNING		DSL modem reset command sent at system start up failed.
00442	INFO	I: VS ST:ss	Vs resource state report. 'ss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE)].
00443	INFO	I: CtiMix-1 ST:ss	CtiMix resource state report. 'ss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE)].
00444	WARNING		Some ABILISPHONE users have been disabled due to licence restrictions.
00445	ERROR		Cannot create new threads, table is ful.
00446	ERROR		Internal system message.
00447	WARNING	W: LICENCE, xx PC-PHONEs NOT ACTIVATED	Some PC-PHONEs not activated due to licence restrictions.
00448	WARNING		Ethernet MAC address has not been properly detected even after 3 attempt of reload from EEPROM.
00449	WARNING		OPC entered USER table overflow state.
00450	WARNING		OPC entered CALL table overflow state.
00451	WARNING		OPC entered CALL QUEUE table overflow state.
00452	ERROR	HF:xxxxxxx	Memory information summary report message: free heap.
00453	WARNING		Required CPU instructions are unavailable.
00454	INFO		VPots CTI port state report.
00455	WARNING		CTIIAX Numbers table reached the overflow state.
00456	WARNING		CTIIAX Numbers table exited the overflow state.
00457	WARNING		CTISIP Numbers table reached the overflow state.
00458	WARNING		CTISIP Numbers table exited the overflow state.
00459	INFO	I: ABILIS-ID:xxxxxx	Abilis CPX serial number.
00460	WARNING		Abilis CPX automatic list's filling has been broken because the Items table is full.
00461	INFO	I: NPv-n ST:ssss	NPv resource state report. 'ssss' is the resource state [UP, DOWN].
00462	INFO	I: NPvl-n P1:ssss P2:- B:- B-C:-	NPV links state report. 'ssss' is the resource state [UP, DOWN].
00463	WARNING		Some CHAT (XMPP) users were not activated due to licence restrictions.
00464	INFO	I: CtiVo ST:ssss	CtiVo resource state report. 'ssss' is the resource state [UP, DOWN].
00465	WARNING		Some VO users were not activated or activated with less channels due to licence restrictions.
00466	WARNING		Some VO users were not activated due to licence restrictions.
00467	INFO	I: TRFA DISA SERVICE xxxxxx DELETED	All TRFA files related to specified DISA service are deleted.
00468	INFO	I: TRFA USER xxxxx DELETED	All TRFA files related to specified USER name are deleted.
00469	INFO	SCHEDULED WARM START (SYSRBCOND)	Conditioned system reboot.
00470	INFO	SCHEDULED WARM START (SYSRBDELAY)	Delayed system reboot.
00471	INFO		System reboot caused by severe RTUSB error.
00472	WARNING		Communication with WDG interrupted: the WDG doesn't respond anymore.
00473	WARNING		Communication with WDG restored after a period of malfunctioning.
00474	INFO	I: CPU clock xxxx MHz	Event reporting the speed of the CPU.
00475	WARNING		Event reporting the CPU speed was calculated on unreliable samples.
00476	WARNING		Event reporting the speed change of the CPU.
00477	INFO	I: DEBUG SIMULATE LOOP (without time limit)	The command DEBUG SIMULATE EVENT:LOOP (without time limit) has been executed.
00478	INFO	I: DEBUG SIMULATE IRQLOOP	The command DEBUG SIMULATE EVENT:IRQLOOP has been executed.
00479	WARNING		System was abnormal rebooted, LIVE state was detected during boot phase, but the current state is not valid.
00480	WARNING		System was rebooted because INTERRUPT MONITOR detected a deadlock.
00481	WARNING		Exception/Warm Start/Restart system/... timed-out report message.
00482	INFO		Default configuration file successfully created at system start-up.
00483	INFO		Default configuration file creation failure at system start-up.
00484	INFO		Event reporting the speed of the CPU (fixed).
00485	INFO		Event reporting the speed of the CPU (unable to fix).
00486	WARNING		Invalid/corrupted Incoming Call log as been renamed to *.bad.
00487	WARNING		Invalid/corrupted Outgoing Call log as been renamed to *.bad.
00488	WARNING		RealTek Ethernet port recovered by AUTO INIT because of serious troubles in RX ring buffer.
00489	INFO	I: Script-1 ST:ss	Script resource state report. 'ss' is the resource state [dn (DOWN), RD (READY), in (INACTIVE)].
00490	WARNING		Licence not activated because max Abilis version is lower then the running Abilis version.
00491	WARNING		Licence not activated because it is missing or not-valid: the new Abilis version run cannot proceed. System is restarted.
00492	WARNING		Some VO users were activated with less channels due to licence restrictions.
00493	WARNING		UPS message that signals forced shutdown event.
00494	WARNING		UPS message that signals unexpected shutdown indication.
00495	WARNING		UPS message that signals battery low condition.
00496	WARNING		UPS message that signals battery good condition.
00497	INFO	I: Ups-n USB-ST:ss	Ups resource state report. 'ss' is the USB state [ ds (DISCONNECTED), CN (CONNECTED)].
00498	INFO	I: Ups-n POWER:s1 BATT:s2	Ups resource report with indication of POWER source and BATTERY state. 's1' is the POWER state [dn (down), UP, NA (Not Available)]. 's2' is the BATTERY state [dn (down), UP, NA (Not Available)].
00499	INFO		System shutdown, requested by UPS.
00500	WARNING		UPS - unsupported FW version.
00501	WARNING		UPS - unsupported PCB version.
00502	WARNING		Event reporting the videosurveillance storage occupation is above the threshold.
00503	INFO		AsyncU resource state report
00504	INFO		IpoE resource state report.
00505	INFO		The command DEBUG SIMULATE EVENT:BLOCKAGE <msec> has been executed.
00506	INFO		Task hook started at boot, with the specified threshold (in ms).
00507	WARNING		Task hook failed to start at boot.