| What's new | ||
|---|---|---|
 |  | |
| What's new | ||
|---|---|---|
| | | |
![[Important]](../images/important.png) | Important |
|---|---|
Remember from release 8.0:
|
New features of the release 8.7:
CF:
Introduced "System CF" classification and handling. Reserved letter D: for a "System CF".
System CF are those CF where Abilis system is installed and that are suitable to boot Abilis. They must satisfy the size requisite >= 100 Mbytes and <= 16 GBytes.
![[Note]](../images/note.png) | Note |
|---|---|
If there was an Hard Disk for Videosurveillance on D: it will be moved to E: |
Double CF handling
with modes NORMAL, NORMAL with
MIRROR, SAFE, SAFE with
MIRROR.
System General:
Reorganised and extended the "System General" configuration (D G, S G) to be better readable and to accommodate new services and features.
Added "Mail Defaults" section.
Added "Compact Flash" section.
Provisioning:
Configuration and licence provisioning, client and server.
LAN monitor:
monitoring of devices connected to a local LAN using ARP packets, with
web pages for configuration and monitor.
Web:
"VPN status": pages for monitoring of AIPT2 VPNs.
Summarized traffic analysis of "line
load" and "top10" for
classified IP interfaces (LAN,
WAN, VPN,
VPNW).
IP router:
Extended IPRES range from 1..250 to 1..999.
Extended IPLB from 8 to 50 IPRES/GW for each IPLB.
DHCP: server
with "per network" server or relay configuration. Modified dhcp server
service so that each subnet can be independently configured for SERVER
or RELAY mode.
DNS: extended with whitelist.
Automation:
Added support for a new set of RIO devices.
Simplified RIO/RVS configuration.
Now the Netmask and the Gateway are automatically loaded from the IPRES where the device has been discovered, and can't be modified.
Communication between Abilis and RIO/RVS are now enforced using the MAC address of the RIO/RVS stored in configuration.
In this way if another device with same IP address of RIO/RVS is connected to the network the communication between the Abilis and the RIO/RVS will not be disturbed.
LCS: added "CALL-BACK"
option for removal or LCS entry.
USB: by default the UHCI and OHCI controllers
(USB 1.1) are not enabled.
| Note |
|---|---|
To enable the UHCI and OHCI controllers, please insert this command: s p usb uhci-ohci:enabled. [09:16:42] ABILIS_CPX: |
![[Tip]](../images/tip.png) | Tip |
|---|---|
For more details, please refer to: Section 6.5.1.2, “D USBDEV (Display USB Devices)”. |
LTE CellKey: added support for HUAWEI E3372
LTE device.
| Note |
|---|---|
A licence for CELLKEY4G is required. |
AIPT2:
Added PATHSMODE
parameter.
It allows a quick setting of paths for "ALL REDUNDANT" and
"ALL BALANCED" paths, and of course also the default
"MIXED" mode.
Added LOCATION
parameter.
Used to insert geographical coordinates of the other side of the tunnel (lat,long). It is used to show place holders in the AIPT2 monitoring map.
TRFA CTI: improved with retries in case of
file occupied, this prevents possible data loss.
TRFA IP:
The data storage of traffic analyser of IP data has been heavily revised:
File names and data structures have been changed.
Files are written much more effectively. In previous versions whole file was rewritten at each interval, now only the new data is written, eventually overwriting too old data.
Files are CONVERTED on first run, more precisely if NEW file is missing and OLD file is present. After the conversion the OLD file is DELETED.
Added HTTP/XML interface for querying and retrieving IP traffic data. The interface is documented and made available for third party use.
ISDN: added for NT the option to provide
date/time in SETUP and CONNECT messages.
A new section "ISDN defaults" has been added in CTISYS to enable it for all NT ports.
Snmp: Updated SNMP MIB to support all new
features in 8.7.0.
