13.2. CITO CTI port configuration

13.2. CITO CTI port configuration
	Chapter 13. CITO-ADAPTER

When a POTS device (POTS, BSE, POTSBOX …) is added in the configuration also its related CTI ports are activated (for further information refer to Section 6.5, “Devices”).

The following command modifies the parameters of a CTI port:

s p ctip:<port_number> <parameter>:<value>

Here is an example of configuration of a POTS port for CITO-ADAPTER:

[20:47:01] ABILIS_CPX:s p ctip:101 num:11 descr:citophone_1 device:cito cdo:33 ring:cito1

COMMAND EXECUTED

The d p ctip ? or d p ctipe ? commands show all available parameters.

[20:47:01] ABILIS_CPX:d p ctip:101

CTIP:101 - Not Saved (SAVE CONF), Not Refreshed (INIT) ------------------------
Act     DESCR:citophone_1
Run     card:BSE-1<9>                   USER:#
        OPSTATE:UP        LOG:NO                               TYPE:USER
        signalling:POTS                                        SS:YES
        DEVICE:CITO       RING:CITO1
        NUM:11                          ADDRBOOK-NUM:NUM
        CDO:33                       

[20:47:59] ABILIS_CPX:d p ctipe:101

CTIP:101 - Not Saved (SAVE CONF), Not Refreshed (INIT) ------------------------
Act     DESCR:citophone_1
Run     card:BSE-1<9>                   USER:#
        OPSTATE:UP        LOG:NO                               TYPE:USER
        signalling:POTS                                        SS:YES
        DEVICE:CITO       RING:CITO1
        NUM:11                          ADDRBOOK-NUM:NUM
        CDO:33                       
        LOOP:NO         TEST:NO           
        CLIP:SYS        CLIP-STD:SYS      CLIP-TAS:SYS    CLIP-LEVEL:SYS
        SENSING:SYS     ABF:SYS  HPF:SYS  DEBOUNCE:SYS    MIN-FLASH:SYS   
        COUNTRY:SYS                                       MAX-FLASH:SYS   
        DIALT:5         IN-GAIN-ADJ:SYS                   OUT-GAIN-ADJ:SYS
        AT:SYS          AT-CODE:SYS     AT-DURATION:SYS   BC:SYS
        DT:SYS          DT-CODE:SYS     DT-DURATION:SYS   OUTDIAL-TONE:SYS
        SS-PICKUP:GROUPS                SS-PRES-CG:YES    NPOO-CT:SYS
        SS-CF-DND:NO                    SS-VM:YES

Meaning of the most important parameters:

LOG

State changes log and alarm generation [NO, D, S, A, L, T, ALL] [+E] (D: Debug Log; S: System Log; A: Alarm view; L: Local audible alarm; T: SNMP traps; +E: Extended Log of state changes).

USER

Name of the user assigned to this port. From 1 up to 32 ASCII characters or "#". The user must be present and it must not be already assigned to another port.

NUM

Phone number assigned to CTI port. The available values are:

*: the Calling Number offered by CTIR is passed transparently to the device;
#: the Calling Number isn't passed to the device;
##: enforces the presentation restricted: the Calling Number isn't passed to the device;
nnnn: exactly this number is passed as Calling Number to the device;
nnnn*: the Calling Number received from CTIR is modified by replacing first four digits with nnnn;
nnnn??: similar to nnnn* with the difference that only an exact number of digits as many ? is passed after nnnn;
????: only an exact number of digits as many ? is passed after the nnnn.

DEVICE

Device mode [PHONE, HEADSET, CITO, HOTEL-PHONE]. HOTEL-PHONE is used to generate an alarm when ground start is made.

RING

Ringining pattern used when calling another POTS port of this Abilis. [CITO1, CITO2, CITO3, EXT, INT].

	Important
	Only for `DEVICE`:`CITO`.

CDO

Number to be called on Auto-connect. # or max 20 digits ['0'..'9'], optionally preceded by TON [u, i, n, o, s, h, k] and/or NP [x, e, d, t, l, p] attributes. See also HELP ISDN ATTRIBUTES.

	Important
	Only for `DEVICE`:`CITO`.

	Caution
	To activate the changes made on the upper case parameters, execute the initialization command init ctisys; while to set act the changes made on the lowercase parameters a save conf and an Abilis restart are required (i.e. With warm start command).


13.1. CITO-ADAPTER		13.3. CTI routing configuration