The QPRIX is a stand-alone card, it has 4 primary interfaces (ISDN-PRI) and supports up to 16 DSP for 64 compressed calls. Besides echo canceller (EC) is available up to 32 ms but it can raise up to 128 ms in the version with the additional Octasic chip (EEC).

Through H.100 bus it can also be connected to other cards of the CTI category.

	Note
	The QPRIX is supported starting from Abilis firmware version 6.3.

Figure 2.25. QPRIX

For the ISDN-PRI (S2M) interfaces no standard physical port is specified. The Abilis QPRIX use RJ45 sockets with the same signal arrangement as the one used to access to BRI NT:

Each interface presents a 120 ohm balanced impedance. Each port can be configured as NT (Network Termination) or TE (Terminal Equipment).

The PB22X is a stand-alone card, it has 2X ISDN Primary Ports (ISDN30) and 2X ISDN Basic Ports (ISDN2).

Through H.100 bus it can also be connected to other cards of the CTI category.

Figure 2.26. PB22

The Abilis PB22 use RJ45 plugs with the following pinout for ISDN-PRI (S2M):

The Abilis PB22 use RJ45 plugs with the following pinout for ISDN-BRI:

The PB44X card has 4 primary interfaces (ISDN-PRI) and, by means of a daughterboard (BRI4ADD, see photo), 4 ISDN Basic Rate (ISDN-BRI) interfaces. All interfaces are freely configurable as NT / TE.

It supports up to 16 DSP for 64 compressed calls and can be connected to other CTI cards through the H.100 bus.

	Note
	The PB44X is supported starting from Abilis firmware version 6.3.

	Tip
	For information about the connection between Abilis and ISDN Basic Rate Interface (BRI) lines refer to Section 3.2, “ISDN Basic Rate Interface (BRI) connection”.

Figure 2.27. PB44X

The PB44X cards use RJ45 plugs with the following pinout, either on the main board (4 PRI ports) or on the extension (4 BRI ports).

Each PRI interface presents a 120 ohm balanced impedance. Each port can be configured as NT (Network Termination) or TE (Terminal Equipment). The BRI ports have to use an impedance matching adapter.

	Warning
	Although only one PCI slot is used for the electrical connection on the external part of the cabinet, the additional 4 BRI ports occupy an additional slot (for mechanical connection only).

The PB44 card has 4 primary interfaces (ISDN-PRI) and, by means of a daughterboard (BRI4ADD, see photo), 4 ISDN Basic Rate (ISDN-BRI) interfaces. All interfaces are freely configurable as NT / TE.

It supports up to 6 DSP for 24 compressed calls and can be connected to other CTI cards through the H.100 bus.

	Tip
	For information about the connection between Abilis and ISDN Basic Rate Interface (BRI) lines refer to Section 3.2, “ISDN Basic Rate Interface (BRI) connection”.

Figure 2.28. PB44

The PB44 cards use RJ45 plugs with the following pinout, either on the main board (4 PRI ports) or on the extension (4 BRI ports).

Each PRI interface presents a 120 ohm balanced impedance. Each port can be configured as NT (Network Termination) or TE (Terminal Equipment). The BRI ports have to use an impedance matching adapter.

	Warning
	Although only one PCI slot is used for the electrical connection on the external part of the cabinet, the additional 4 BRI ports occupy an additional slot (for mechanical connection only).

The BRI-HFC3-LP card does the same work as a composite system made with: CTI board + BRI-4 (or BRI-8) module + DSP, but its cost is lower. It supports one/two DSP to manage four or eight simultaneous VoIP calls.

The DSPs now supports g.729 codec; besides all BRI-HFC cards are equipped with H100 bus.

	Note
	The BRI-HFC3-LP is supported starting from Abilis firmware version 7.7.

	Tip
	For information about the connection between Abilis and ISDN Basic Rate Interface (BRI) refer to Section 3.2, “ISDN Basic Rate Interface (BRI) connection”.

Figure 2.29. BRI-HFC3-LP

The BRI-HFC3-LP cards use RJ45 plugs with the following pinout:

Each is freely configurable (at the logical level) like NT (Network Termination) or TE (Terminal Equipment). The BRI ports require an impedance matching adapter.

	Tip
	Interesting chapter: Section 80.9, “How to know which kind of hardware is mounted on Abilis”.

The POTS cards belong to the CTI family and are used to connect analog telephones to the Abilis system. POTS are available with 4, 8 or 16 FXS (BCA) interfaces. Through the H.100 bus, when installed on the same Abilis, several POTS cards behave like a single module (it works also with CTI or BRI-HFC cards). In this way, Abilis becomes a powerful PBX system.

Figure 2.32. POTS

POTS cards have four RJ45 sockets. Each socket is to be used with an octopus cable (one RJ45 plug <-> four RJ11 plugs). Each RJ11 is for one telephone.

Figure 2.33. “Octopus” POTS Cable

The octopus for POTS uses the following pinout.

Figure 2.34. “paraOctopus” POTS Cable pinout

	Note
	A variable delay to the start of ring signals is used to prevent a current overload in case of multicast groups with large numbers of Pots ports. The delay is in the range of 20 to 140 msec.

	Tip
	Interesting chapters: Section 80.9.1, “How to recognize PCI cards model”; Chapter 56, CTI System; Section 82.2, “How to configure FXS (POTS) ports for analog telephones or FAX machines”.

This device allows protecting POTS ports from external overvoltages and overcurrents such as the ones generated from lightning.

It's equipped with:

Figure 2.35. POTS protection

	Tip
	Interesting chapters: Section 3.8, “POTS protection connection”; Section 2.11.7, “POTS 4/8/16”; Chapter 56, CTI System; Section 82.2, “How to configure FXS (POTS) ports for analog telephones or FAX machines”.

The POTSHUB is a PCI card equipped with 1xH.100 connector (internal) and 4xRJ45 connectors (external) for Abilis proprietary ELTI (External LVDS TDM interface) interface. The ELTI interface is used to connect the POTSBOX chassis which offers up to 32 POTS interfaces. Up to 4 POTSBOX can be connected to a POTSHUB card, and up to 3 POTSHUB card can be installed for a maximal of 384 POTS ports.

Figure 2.42. POTSHUB

	Note
	The POTSHUB is supported starting from Abilis firmware version 7.2.

	Tip
	Interesting chapters: Section 3.11, “POTSBOX connection”; Section 12.1, “POTSBOX device activation”.

The Ethernet card provides a Fast Ethernet interface with Auto-Mode (10–100 Mbps) and Auto-TP (signal polarity) features. Several Ethernet cards can be installed into the same CPX.

Figure 2.43. Ethernet card

	Tip
	Interesting chapters: Section 25.3, “IP Resources”; Section 81.2, “How to activate a new Ethernet port”.

The GigaEthernet card provides a Gigabit Ethernet interface with Auto-Mode (10/100/1000 Mbps) and Auto-TP (signal polarity) features. Several GigaEthernet cards can be installed into the same CPX.

Figure 2.44. Gigabit Ethernet

	Tip
	Interesting chapters: Section 25.3, “IP Resources”; Section 81.2, “How to activate a new Ethernet port”.

The QUAD-Ethernet card provides a 4 Fast Ethernet interface with Auto-Mode (10–100 Mbps) and Auto-TP (signal polarity) features. Several QUAD-Ethernet cards can be installed into the same CPX.

Figure 2.45. Quad-Ethernet

Figure 2.46. Quad-Ethernet PCI Express

	Tip
	Interesting chapters: Section 25.3, “IP Resources”; Section 81.2, “How to activate a new Ethernet port”.