53.1. TRFA resource

The Abilis TRFA resource is divided in two section:

The Abilis IP TRFA resource provides the following features:

The Abilis CTI TRFA resource provides the following features:

[Note]Note

The Phone TRFA for DISA service it's only for DISA service MODE:ACD.

Configuring the TRFA resource and the section inside the IP resources are needed to activate the IP Traffic Analyzer.

53.1.1. Activating the TRFA resource

Add the resource to the Abilis system with the following command:

[11:01:39] ABILIS_CPX:a res:trfa

RES:TRFA ALREADY EXISTS

The TRFA resource may already exist in the system, but may not yet be active: set it active with the command:

[11:01:48] ABILIS_CPX:s act res:trfa

COMMAND EXECUTED
[Caution]Caution

After adding or setting the TRFA active, you must restart the Abilis to make the resource running (use the command warm start to reboot the Abilis).

[11:01:39] ABILIS_CPX:s p trfa act:yes

COMMAND EXECUTED

[11:01:39] ABILIS_CPX:d p trfa

RES:Trfa ----------------------------------------------------------------------
Run    DESCR:Traffic_Analyzer
       LOG:DS               ACT:YES              rt-max-clients:20
       WDIR:C:\APP\TRFA\
       - IP section -----------------------------------------------------------
       ACT-IP:YES           max-addresses:1000   max-png:5      
       - CTI section ----------------------------------------------------------
       ACT-CTI:YES        
         - Cti Router ---------------------------------------------------------
         N1:#                              N1-NAME:
         N2:#                              N2-NAME:
         N3:#                              N3-NAME:
         N4:#                              N4-NAME:
         N5:#                              N5-NAME:
         N6:#                              N6-NAME:
         N7:#                              N7-NAME:
         N8:#                              N8-NAME:
         N9:#                              N9-NAME:
         N10:#                             N10-NAME:

53.1.2. TRFA resource parameters

Use the following command to display the parameters of the resource; the d p trfa ? command shows the meaning of parameters.

[17:06:43] ABILIS_CPX:d p trfa

RES:Trfa ----------------------------------------------------------------------
Run    DESCR:Traffic_Analyzer
       LOG:DS               ACT:YES              rt-max-clients:20
       WDIR:C:\APP\TRFA\
       - IP section -----------------------------------------------------------
       ACT-IP:YES           max-addresses:1000   max-png:5      
       - CTI section ----------------------------------------------------------
       ACT-CTI:YES        
         - Cti Router ---------------------------------------------------------
         N1:#                              N1-NAME:
         N2:#                              N2-NAME:
         N3:#                              N3-NAME:
         N4:#                              N4-NAME:
         N5:#                              N5-NAME:
         N6:#                              N6-NAME:
         N7:#                              N7-NAME:
         N8:#                              N8-NAME:
         N9:#                              N9-NAME:
         N10:#                             N10-NAME:

Meaning of the most important parameters:

LOG

Logging functionalities activation/deactivation.

ACT

Operation activation [NO, YES].

rt-max-clients

Number of monitors that can require information from TRFA [1..50]. NOTE: an equal of greater number of HTTP sessions must be available.

WDIR

Directory where traffic data files are stored. Full path with drive letter ['C'..'Z'] terminated by '\'. Max 128 chars. Spaces require double quotes (E.g. "C:\My dir\").

ACT-IP

IP traffic analysis activation [NO, YES].

max-addresses

Maximum number of pair IPP + IP address in the address table [2..8000].

max-png

Maximum number of PNG shell objects that will be used for create PNG files [1..20].

ACT-CTI

CTI traffic analysis activation [NO, YES].

N1..N10

Numbers set. Calls with called number (CD) that matches Nxx are counted in the TRFA statistics of number set with Nxx-NAME. Search for match is performed sequentially from N1 to N10. Max 20 characters, in the range ['0'..'9', '*'] optionally preceded by TON [u, i, n, o, s, h, c] and/or NP [x, e, d, t, l, p] attributes or * or # or the name of an IN/RU/MR list between single quotes (e.g. 'listname' or # or ux123* or 555 or *). The '*' is allowed only alone or as the last character. See also HELP ISDN ATTRIBUTES.

N1-NAME..N10-NAME

Numbers set name. Max 16 characters. Space not allowed. If name is cleared, the numbers set statistics are cleared.

The following command allows the administrator to change the configuration of the resource:

s p trfa parameter:value...

[Caution]Caution

To activate the changes made on the upper case parameters, execute the initialization command init trfa; while to set act the changes made on the lowercase parameters a save conf and an Abilis restart are required (i.e. With warm start command).

53.1.3. Activating the IP TRFA

Use the command below to activate the IP Traffic Analyzer:

[17:45:30] ABILIS_CPX:s p trfa act-ip:yes

COMMAND EXECUTED
[Caution]Caution

To activate the changes made, execute the initialization command init trfa. Remember to save the configuration (save conf).

To activate the traffic survey for an IP resource, type:

[17:45:32] ABILIS_CPX:s p ip-1 trfa:yes

COMMAND EXECUTED

[17:45:41] ABILIS_CPX:d p ip-1

RES:Ip-1 - IP over LAN (LAN) --------------------------------------------------
Run    DESCR:LAN
       OPSTATE:UP             LOG:NO                 STATE-DETECT:NORMAL
       LANRES:Eth-1
       IPADD:192.168.029.254  MASK:255.255.255.000   
       REDIS:EXT     HIDE:NO         RP:NONE            IPSEC:NO       VRRP:NO
       NAT:INSIDE    UPNP:NO         DIFFSERV:NO        DDNS:NO
       OUTBUF:100    OUTQUEUE:FAIR   MTU:1500          
       OUTSPL:NO     
       INBUF:0                       mru:1500           SRCV:NO
       - TRFA section ---------------------------------------------------------
       TRFA:YES     TRFA-MODE:TOTALS       
       - Lan ------------------------------------------------------------------
       LLOG:NO       arpcache:200    CACHETIMER:120     rxbuf:4     txbuf:14
       VLAN-ID:UNTAG 
RES:Eth-1 ---------------------------------------------------------------------
Run    DESCR:
       LOG:DS            MODE:AUTO         DUPLEX:HALF
       MAC-ADDR:FACTORY (00-E0-C5-54-A2-78) 
       dma-rxbuf:250     dma-txbuf:25      max-vlans:0
       ip-rxbuf:25       arp-rxbuf:5       pppoed-rxbuf:5    pppoes-rxbuf:25 
[Caution]Caution

To activate the changes made, execute the initialization command init res:ip-1. Remember to save the configuration (save conf).

In the “TRFA Section” the following parameters will appear:

TRFA

Enables/disables traffic analysis.

TRFA-MODE

Select traffic analysis mode [TOTALS: saves the total global traffic; PROT: subdivides the registration for the main protocol models; IP: saves the totals for every single IP address; IP-PROT: subdivides the traffic by protocol, for every single crossing IP address];

IP-RESERVE

Reserves records in the traffic analysis data base: it represents the maximum IP number trace.

TRFA-SIDE

Selects IP address type [LOCAL: analyse destination IP address in output packets and source IP in input packets; REMOTE: analyse source IP address in output packets and destination IP address in input packets, applying address translation if packets have been natted to/from the remote IP resource].

TRFA-IPADD

IP address filter:

- '*': any IP address.

- 'LOCALNET': allowed only for TRFA-SIDE:LOCAL.

- a single IP address or two IP addresses separated by ':' (colon) [1.0.0.0-126.255.255.255, 128.0.0.0-223.255.255.255].

- the name of an IP/IR list between single quotes (E.g.: * or LOCALNET or 150.1.1.1 or 192.1.0.0:192.1.0.9 or 'List').

53.1.4. Activating the CTI TRFA

Use the command below to activate the Phone Traffic Analyzer:

[17:45:32] ABILIS_CPX:s p trfa act-cti:yes

COMMAND EXECUTED
[Caution]Caution

To activate the changes made, execute the initialization command init trfa. Remember to save the configuration (save conf).

53.1.4.1. Activating the CTI TRFA for DISA service

To activate the traffic survey for an DISA service, type:

[17:45:32] ABILIS_CPX:s ctidisa service:test trfa:normal

COMMAND EXECUTED

[17:45:41] ABILIS_CPX:d ctidisa service:test

Total number of services:2

-------------------------------------------------------------------------------
SERVICE:test               DESCR:
  MODE:        ACD                    |INTRO-STATE:   CREQ  |INTRO:    
  ROUTING:     PREFIX                 |CONN-DELAY:    0     |WELCOME:  
  MAX-CALLS:   NOMAX                  |PC-OFFER:      *     |INITDIAL: test
  BC:          Speech                 |TRANSFER:      NO    |AFTERPIN: #
  CB:          NO                     |ACD-INTERVAL:  15    |LOOPDIAL: 
  CB-DELAY:    5                      |DIAL-TOUT:     30    |IDENFAIL: 
  CB-NRTY:     1                      |PIN-TOUT:      15    |CALLNA:   
  CB-UNK-CDO:  'CGI'                  |NUM-TOUT:      15    |ALERT:    test
  CB-NAT-CDO:  0'CGI'                 |BUSYDISC:      4     |BUSY:     
  CB-INT-CDO:  00'CGI'                |LOOP-BUSY:     YES   |NOANSWER: 
  CB-CGO:      #                      |LOOP-NOANSWER: YES   |DISC:     
  CTIP-TYPE-O: *                      |LOOP-DENIED:   YES   |HOLD:     
  AUTO-CDO:    9999                   |LOOP-OTHER:    YES   |BYE:      #
  TOUT-CDO:    #                      |MAX-LOOPS:     99 
  END-CDO:     #                      |MAX-LOOPS-CDO: #  
  PERMIT:      *                      |TRFA:          NORMAL                    
  CDI:         777                    
  CGI:         #
  SUB-SERVICE: #
-------------------------------------------------------------------------------
[Caution]Caution

To activate the changes made, execute the initialization command init res:ctidisa. Remember to save the configuration (save conf).

[Note]Note

The Phone TRFA it's possible to activate only for DISA service MODE:ACD.

53.1.4.2. Activating the Phone TRFA for a specific called number

To activate the traffic survey for a specific called number (222), type:

[17:45:32] ABILIS_CPX:s p trfa n1:222 n1-name:sip_phone

COMMAND EXECUTED

[17:45:41] ABILIS_CPX:d p trfa

RES:Trfa - Not Saved (SAVE CONF), Not Refreshed (INIT) ------------------------
       ------------------------------------------------------------------------
Run    DESCR:Traffic_Analyzer
       LOG:DS               ACT:YES              rt-max-clients:20
       WDIR:C:\APP\TRFA\
       - IP section -----------------------------------------------------------
       ACT-IP:YES           max-addresses:1000   max-png:5      
       - CTI section ----------------------------------------------------------
       ACT-CTI:YES        
         - Cti Router ---------------------------------------------------------
         N1:222                            N1-NAME:sip_phone
         N2:#                              N2-NAME:
         N3:#                              N3-NAME:
         N4:#                              N4-NAME:
         N5:#                              N5-NAME:
         N6:#                              N6-NAME:
         N7:#                              N7-NAME:
         N8:#                              N8-NAME:
         N9:#                              N9-NAME:
         N10:#                             N10-NAME:
[Caution]Caution

To activate the changes made, execute the initialization command init trfa. Remember to save the configuration (save conf).

53.1.4.3. Activating the Phone TRFA for a specific user

To activate the traffic survey for a specific user, type:

[14:53:20] ABILIS_CPX:s pref user:test cti-trfa:yes

COMMAND EXECUTED

[14:53:28] ABILIS_CPX:d pref user:test

Parameter:          | Value:
--------------------+----------------------------------------------------------
USER:                 test
ID:                   8                                             <Read Only>
LAST-CHANGE:          03/10/2015 15:02:30 CET                       <Read Only>
PWD:                  ***
- CTIP not active --
- CLUS not active --
- IAX not active ---
--------------------
SIP-CLIP:             TRANSP
SIP-ACTION:           ADVANCED (No rules)
SIP-CF-RULE:          ALWAYS
SIP-CF-TOUT:          15
SIP-CF-DLY:           10
SIP-CF-FORK-TYPE:     STD
SIP-CF-CDO:           #
SIP-CF-CGO:           *
SIP-VM:               NO
SIP-VM-RULE:          NOANS,OTHERS
SIP-VM-TOUT:          15
SIP-PC-OFFER:         4
SIP-MAIL-FAIL:        NO
SIP-MAIL-FWD:         NO
SIP-MAIL-SEIZED:      NO
- VO not active ----
--------------------
VM-MAIL-TO-LIST:      #
VM-MAIL-TO:              
VM-OGM-MSG:           Message
VM-END-MSG:           SYS
--------------------
MAIL-BODY:            SYS
MAIL-TO-LIST:         #
MAIL-TO-DFT:        
--------------------
CTI-CALLS-LOG:        YES
CTI-CALLS-LOG-IN:     200
CTI-CALLS-LOG-OUT:    200
--------------------
CTI-TRFA:             YES
--------------------
CALLTRY-TOUT:         SYS
CALLTRY-NRTY:         SYS
--------------------
TON-TO-PREFIX:        SYS
--------------------
ON-DEMAND-VR:         NO
ON-DEMAND-VR-MAIL-TO:    
--------------------
OPC-MAIN-INTERFACE:   SIP
-------------------------------------------------------------------------------
[Caution]Caution

Remember to save the configuration (save conf).