Chapter 80. HowTo - Networking
Part VI. HowTo
HowTo - Networking
Table of Contents
80.1. How to configure LAN settings
80.2. How to activate a new Ethernet port
80.3. How to activate a new USB Ethernet port
80.4. How to assign several IP addresses to the same LAN port
80.5. How to assign a VLAN for Ethernet interface
80.5.1. How to assign multiple VLANs to the same Ethernet interface
80.6. How to change the MAC address of the Ethernet or EthernetUSB interface
80.7. How to configure ADSL connections using USB modems
80.7.1. How to configure a RFC 1483 connection
80.7.2. How to configure a PPPoA (RFC 2364) connection
80.7.3. How to configure a PPPoE connection
80.7.4. How to configure a IPoE connection with static IP
80.7.5. How to configure a IPoE connection with dynamic IP
80.8. How to configure ADSL/VDSL connections using Ethernet modems
80.8.1. Ethernet: How to configure a PPPoE connection
80.8.2. Ethernet: How to configure a IPoE connection with static IP
80.9. How to configure VDSL connections using USB modems
80.9.1. VDSL: How to configure a PPPoE connection
80.9.2. VDSL: How to configure a IPoE connection with static IP
80.10. How to configure UMTS-BOX or LTE-BOX as gateway for the Internet
80.11. How to configure UMTS-BOX or LTE-BOX as backup for the Internet
80.12. How to configure the default IP route
80.12.1. How to configure the default IP route in case Abilis is connected to an ADSL USB or V.35/G.703 modem
80.12.2. How to configure the default IP route in case Abilis is connected to an Ethernet ADSL router
80.12.3. How to configure an alternative default IP route
80.13. How to configure the Network Address Translation (NAT)
80.14. How to share a single Internet connection among multiple computers
80.15. How to access IP hosts and services which are behind a NAT manager (port forwarding)
80.16. How to configure the NAT loopback
80.17. How to redirect DNS requests to Abilis
80.18. How to setup DDNS service on Abilis
80.18.1. How to setup DDNS service using dyndns.org
80.18.2. How to setup DDNS service on Abilis
80.19. How to configure a Remote Access Server (RAS)
80.19.1. How to configure a RAS using IPSEC VPN server
80.19.2. How to configure a RAS using IPSEC VPN server with iPhone/iPad or Mac
80.19.3. How to configure a RAS using PPPoE connections with an Ethernet/WiFi network
80.19.4. How to configure a RAS using ISDN network
80.20. How to configure an ISDN PPP Dial-UP connection
80.21. How to configure a VPN tunnel between two Abilis
80.21.1. How to configure a VPN tunnel where both Abilis have a static public IP address
80.21.2. How to configure a VPN tunnel where one Abilis has a dynamic public IP address or is placed behind a router doing NAT/PAT
80.21.3. How to configure a VPN tunnel with the “
backup over ISDN
” option
80.21.4. How to configure a VPN tunnel with the “
double path
” option
80.22. How to configure more VPN tunnels into IP Load Balancing (IPLB)
80.23. How to configure a voice tunnel between two Abilis
80.23.1. How to configure a voice tunnel where both Abilis have a static public IP address
80.23.2. How to configure a voice tunnel where one Abilis has a dynamic public IP address or is placed behind a router doing NAT/PAT
80.23.3. How to configure a voice tunnel with the “
backup over ISDN
” option
80.23.4. How to configure a voice tunnel with the “
double-path
” option
80.24. How to activate the DHCP resource
80.24.1. How to activate the DHCP in relay mode
80.24.2. How to activate the DHCP in server mode
80.24.3. How to activate the DHCP in client mode
80.25. How to activate the IP TRFA resource
80.26. How to use state detection of IP interfaces
80.27. How to activate the SNTP resource
80.27.1. How to activate the SNTP client
80.27.2. How to activate the SNTP server
80.28. How to activate the SNMP agent
80.29. How to publish the users on the Abilis LDAP server
